Product Overview
This manual provides detailed instructions for the Lemokey G1 Wireless Mouse, equipped with a PixArt 3950 sensor. It covers setup, connectivity options, indicator lights, and operational features.
Parts Identification
An illustration shows the top and bottom views of the Lemokey G1 mouse, along with the 2.4GHz receiver. Numbered labels point to the following components:
- 1. Left button
- 2. Right button
- 3. Middle wheel button
- 4. Forward button
- 5. Backward button
- 6. Mouse indicator light
- 7. DPI button
- 8. Modes toggle switch (Labeled B/OFF/G)
- 9. 2.4GHz Type-A receiver
- 10. Receiver compartment (located on the bottom of the mouse)
3 Modes of Connection
Wired Mode:
1. When the mode switch is in the "OFF" position, the mouse will not respond if the cable is not connected.
2. Connect the cable to the Type-C port of the mouse and the USB port on your device. The mouse is ready to use once the indicator light turns on.
* When connected by cable, the mode will default to wired mode even if the toggle is set to Bluetooth or 2.4GHz mode.
Diagram description: Illustrations show a laptop, two USB Type-C cables, and the mouse, connected with plus signs indicating assembly.
2.4GHz Mode:
1. Switch the mode toggle to "G" (2.4GHz mode). The mouse will automatically enter 2.4GHz pairing mode, and the mouse indicator will slowly flash green.
2. Connect the 2.4GHz receiver to your device's USB port. Once successfully connected, the mouse indicator will turn solid green for 3 seconds before dimming off. The mouse is now ready for use.
3. In 2.4GHz pairing mode, the mouse indicator will slowly blink green for 3 minutes. If the mouse is not connected within 3 minutes, the indicator will turn off. To reconnect, hold both the "Left button + Middle Wheel + Right button" for 4 seconds to re-enter pairing mode.
* If you need to repair the connection in 2.4GHz mode, please unplug the 2.4GHz receiver first. Then, hold both the "Left button + Middle Wheel + Right button" for 4 seconds, wait for the green light indicator to start flashing, and plug the 2.4GHz receiver back in to complete the pairing process.
Diagram description: Shows the mode toggle switch set to 'G' (2.4GHz mode). Another diagram shows holding the Left, Middle Wheel, and Right buttons simultaneously for 4 seconds to enter forced pairing mode. A final diagram illustrates connecting the Type-C cable, adapter, and 2.4GHz receiver to a laptop.
Note: It is recommended that when pairing the G1 in 2.4GHz mode, the mouse should be within 20cm of the receiver.
Note: For the best wireless experience, Lemokey recommends using the cable and placing the 2.4GHz receiver somewhere on your desk close to your mouse for a lower rate of latency and fewer signal interferences.
Bluetooth Mode:
1. Switch the mode toggle to "B" (Bluetooth mode). The mouse will automatically turn on Bluetooth pairing mode, and the mouse indicator will slowly flash blue.
2. Open your device's Bluetooth settings, search for a device named "Lemokey G1", then click "connect" to complete pairing.
3. When in Bluetooth pairing mode, the mouse indicator will slowly blink blue for 3 minutes. If it's not connected within 3 minutes, the mouse indicator will turn off. To reconnect, hold the "Left button + Middle Wheel + Right button" for 4 seconds to re-enter pairing mode. The indicator will slowly blink blue.
4. If the G1 is in Bluetooth mode and needs to pair with a new device, hold both the "Left button + Middle Wheel + Right button" for 4 seconds and wait for the blue light to flash on. At this point, Bluetooth has re-entered pairing mode, and you can connect the new device to the G1.
Diagram description: Shows the mode toggle switch set to 'B' (Bluetooth mode). An illustration depicts a laptop with Bluetooth enabled, searching for and connecting to 'Lemokey G1'. A separate illustration shows holding the Left, Middle Wheel, and Right buttons simultaneously for 4 seconds to re-enter pairing mode.
Indicator Lights
Status Indicator
| Mode | Indicator Behavior |
|---|---|
| 2.4GHz Mode | *The mouse indicator slowly blinks green - Ready to be paired. *The mouse indicator quickly blinks green - Pairing with the previous device. |
| Bluetooth Mode | *The mouse indicator slowly blinks blue - Ready to be paired. *The mouse indicator quickly blinks blue - Pairing with the previous device. |
| Low Power | The mouse indicator will slowly blink red. |
DPI Indicator
| Light Color | DPI Value |
|---|---|
| White light | 400 DPI |
| Green light | 800 DPI |
| Blue light | 1600 DPI (default) |
| Yellow light | 3200 DPI |
| Red light | 5000 DPI |
Report Rate Indicator
| Indicator Color | Report Rate / Hz | Available Modes |
|---|---|---|
| White | 125 | 2.4G / BT / Wired |
| Green | 500 | 2.4G / Wired |
| Blue | 1000 | 2.4G / Wired (default) |
| Yellow | 2000 | 2.4G / Wired |
| Red | 4000 | 2.4G / Wired |
| Purple | 8000 | 2.4G / Wired |
*Please adjust the report rate in the driver software.
Software and Maintenance
Driver Software
The Lemokey G1 mouse driver can be selected on launcher.lemokey.com. If the driver software can't connect to the mouse, please contact Lemokey for technical support.
Auto-Sleep Mode
Auto-Sleep mode will not be activated when in wired mode. When in Bluetooth mode or 2.4GHz mode, the mouse will go to Auto-Sleep mode after 10 minutes of sitting idle to save the battery. Move or click the mouse to wake it up.
How to Factory Reset
Hold down both the "DPI" button and "Middle Wheel" button for 4 seconds. All LED lights on the mouse will blink, and then blink three times to indicate that the factory reset is successful.
Diagram description: Illustrations show the bottom of the mouse with the DPI button and Middle Wheel button highlighted, and a hand pressing them simultaneously for 4 seconds to start the factory reset.
Charging Indicator Explanation
| Status | Indicator Behavior |
|---|---|
| Fully Charged | The mouse indicator will stay GREEN. |
| Low Power | The mouse indicator will slowly blink RED. |
* The mouse is compatible with all USB ports. For the best signal and charging speed, connecting to the USB3.0 port is recommended when charging or in use.
* If the mouse is connected by the USB Type-C cable when charging but not paired with any devices:
- The mouse indicator will stay RED when charging.
- The mouse indicator will stay GREEN when fully charged.
Note: The product supports up to 5V charging voltage and 300 mA charging current. Lemokey is not responsible for any problems caused by improper recharging.
Package Contents and Specifications
What's in the Box
- Mouse x 1
- Extension adapter x 1
- User manual x 1
- Type-C cable x 1
- Type-A receiver x 1
- Type-A to Type-C adapter x 1
Mouse Specification
| Feature | Details |
|---|---|
| Size | 116.8*59.5*39.4mm |
| Weight | 55 ± 3g |
| Report Rate (polling rate) | 125(White) - 500(Green) - 1000(Blue) - 2000(Yellow) - 4000(Red) - 8000(Purple) |
| Sensor | PixArt 3950 |
| Resolution | 100 - 30000 DPI |
| Mouse micro switches | Huano Micro Switch (80 million clicks life time) |
| 2.4GHz / Bluetooth connection range | Approx 10m of open space |
| Battery capacity | 600mAh |
| Usage duration | 140 Hours (Bluetooth mode) 120 Hours (1000hz) 45 Hours (4000hz) 40 Hours (8000hz) |
| Recharge time | 2.5 Hours |
| Charging port | USB Type-C |
| Connection mode | 2.4GHz - Bluetooth - Wired |
| Device name | Lemokey G1 |
Contact Information
Find us at:
- https://www.lemokey.com
- Support@lemokey.com
- Facebook: @lemokey
- Instagram: @lemokey.keyboard
- X (Twitter): @lemokey_com
Designed by Lemokey
Made in China
