Inventor Air Conditioning Systems

USER'S MANUAL

This manual provides instructions for the remote controller of Inventor air conditioning systems. It covers specifications, handling, buttons and functions, screen indicators, basic and advanced functions.

Remote Controller Specifications

Model: RG081A3(2S)/BGEF, RG081A3(2S)/BGEFL

Rated Voltage: 3.0V (Dry batteries R03/LR03×2)

Signal Receiving Range: 8m

Environment: -5°C~60°C (23°F~140°F)

Quick Start Guide

1. FIT BATTERIES: Slide the back cover down, insert batteries matching (+) and (-) ends, slide cover back.
2. SELECT MODE: Use the 'M' button to cycle through Auto, Cool, Dry, Heat, Fan modes.
3. SELECT TEMPERATURE: Use the '+' and '-' TEMP buttons to adjust the temperature.
4. SELECT FAN SPEED: Use the 'FAN' buttons (up and down arrows) to adjust fan speed.
5. POINT REMOTE TOWARD UNIT: Ensure a clear line of sight.
6. PRESS POWER BUTTON: Press the power button to turn the unit on or off.

Special Note: Button designs may vary. If a function is not available on the indoor unit, the corresponding button will have no effect. In case of discrepancies between manuals, the "USER'S MANUAL" description prevails.

Handling the Remote Controller

Inserting and Replacing Batteries

To insert or replace batteries:

1. Slide the back cover downwards to expose the battery compartment.
2. Insert batteries, ensuring correct polarity (+/-).
3. Slide the battery cover back into place.

Remote Control

• Direct sunlight can interfere with the infrared signal receiver.
• Maintain a clear line of sight between the remote and the appliance.
• If the remote controls another appliance, move the appliance or contact customer service.

Battery Disposal

• Do not dispose of batteries as unsorted municipal waste. Follow local laws for proper disposal.
• Batteries may contain chemical symbols indicating heavy metals (e.g., Pb for Lead).
• Dispose of appliances and used batteries at specialized facilities for reuse, recycling, and recovery to avoid negative environmental and health impacts.

Battery Performance

• For optimal performance, do not mix old and new batteries or batteries of different brands.
• Remove batteries if the device will not be used for more than 2 months.

Notes for Using Remote Control

This device complies with national regulations. In Canada, it complies with CAN ICES-3(B)/NMB-3(B). In the USA, it complies with Part 15 of the FCC Rules, subject to conditions that it does not cause harmful interference and accepts any interference received.

This equipment has been tested and found to comply with Class B digital device limits per FCC Rules, designed to provide reasonable protection against harmful interference in residential installations. It generates, uses, and can radiate radio frequency energy. If not installed and used per instructions, it may cause harmful interference to radio communications. If interference occurs, try the following:

• Reorient or relocate the receiving antenna.
• Increase separation between equipment and receiver.
• Connect equipment to a different circuit.
• Consult the dealer or an experienced radio/TV technician.
• Unauthorized modifications may void the user's authority to operate the equipment.

Buttons and Functions

Familiarize yourself with the remote controller before use. Refer to the "How to Use Basic Functions" section for detailed operation instructions.

Models: RG081A3(2S)/BGEF, RG081A3(2S)/BGEFL (Fresh feature not available for some models)

Remote Screen Indicators

Information displayed when the remote controller is powered on:

• Breeze away: For directing airflow away from the user.
• Not available for this unit: Indicates a feature not supported by the specific model.
• Sleep mode: For comfortable sleep environment.
• Follow me: Remote measures ambient temperature.
• Active Clean: For purifying air.
• Fresh mode: For air purification.
• Gear: Energy saving mode.
• Wireless control: For Wi-Fi connectivity.
• Low battery (flashes): Indicates low battery.

Temperature/Timer/Fan speed display: Shows set temperature, fan speed, or timer settings.

FAN SPEED indicators show levels from 1-10% to 91-100%. Fan speed cannot be adjusted in AUTO or DRY mode.

Other Indicators:

• Transmission Indicator: Signal strength.
• ECO feature: Energy saving.
• Silent feature: Quiet operation.
• Turbo feature: High fan speed.
• INVALID: Indicates an invalid operation.
• Timer ON/OFF: Timer settings.
• Vertical louver swing: Controls louver movement.
• Not available for this unit: Feature not supported.

MODE display: Shows the current mode (AUTO, COOL, DRY, HEAT, FAN).

Note: Only relevant function indicators are shown during operation.

How to Use Basic Functions

NOTE: Ensure the unit is plugged in and has power before operation.

AUTO mode

1. Select AUTO mode.
2. Set desired temperature.
3. Turn on the air conditioner.

Note: In AUTO mode, the unit automatically selects COOL, FAN, or HEAT based on temperature. Fan speed cannot be set in AUTO mode.

COOL or HEAT mode

1. Select COOL/HEAT mode.
2. Set the temperature.
3. Set the FAN speed.
4. Turn on the air conditioner.

DRY mode

1. Select DRY mode.
2. Set the desired temperature.
3. Turn on the air conditioner.

Note: Fan speed is automatically controlled in DRY mode and cannot be set manually.

FAN mode

1. Select FAN mode.
2. Set the FAN speed.
3. Turn on the air conditioner.

Note: Temperature cannot be set in FAN mode, so it is not displayed on the remote's screen.

Setting the TIMER

TIMER ON/OFF

Set the time for the unit to automatically turn on/off.

TIMER ON setting

1. Press the TIMER button to initiate the ON sequence.
2. Use TEMP +/- or FAN +/- buttons to set the desired ON time.
3. Press OK to confirm and activate the timer.

TIMER OFF setting

1. Press the TIMER button to initiate the OFF sequence.
2. Use TEMP +/- or FAN +/- buttons to set the desired OFF time.
3. Press OK to confirm and activate the timer.

Note:

• Time increments are 30 minutes up to 10 hours, then 1-hour increments up to 24:00. The timer resets to 0:00 after 24:00.
• Cancel timer function by setting the time to 0:00h.

TIMER ON & OFF setting (example)

Set time periods refer to hours after the current time.

Example: If current time is 1:00 PM, setting the timer for 2.5 hours ON and 5 hours OFF means the unit will turn on at 3:30 PM and turn off at 6:00 PM.

How to Use Advanced Functions

Swing function

Vertical louver movement:

• Press SWING button repeatedly (within 3 seconds) for: Stop swing > Start swing > Louver angle 1-5.
• Press SWING button repeatedly (more than 3 seconds) for: Fixed angle > Start swing > Stop swing.

SLEEP function

Note: SLEEP function is not available in FAN and DRY modes.

The SLEEP function creates a more comfortable sleeping environment. Fan speed is adjustable in COOL/HEAT modes. In AUTO mode, fan speed is fixed.

• COOL mode: Temperature increases by 1°C (2°F) after 1 hour, and another 1°C (2°F) after the second hour.
• HEAT mode: Temperature decreases by 1°C (2°F) after 1 hour, and another 1°C (2°F) after the second hour.
• After two hours, the temperature remains constant. The sleep function ends automatically after eight hours.

Silent function

Press and hold the FAN button for more than 2 seconds to activate/disable Silent function. This may result in reduced cooling/heating capacity due to low-frequency compressor operation.

FP function

In HEAT mode, set temperature to 16°C/60°F. Press the button twice within one second to activate FP function. The unit will operate at high fan speed with temperature automatically set to 8°C/46°F. Pressing ON/OFF, Mode, Fan, or Temp buttons cancels this function.

LED display

• Press the LED button to turn the indoor unit's display and buzzer on/off.
• Press and hold the LED button for more than 5 seconds (some units) to display the actual room temperature. Pressing again for more than 5 seconds reverts to the set temperature display.

Eco/Gear function

Press the button to cycle through energy-saving modes: ECO → GEAR (75%) → GEAR (50%) → ECO...

Note: This function is available only in COOL mode.

ECO operation

In COOL mode, the temperature is automatically set to 24°C/75°F with AUTO fan speed for energy saving. If the set temperature is above 24°C/75°F, fan speed changes to AUTO, and the set temperature remains unchanged.

NOTE: ECO operation stops if you press the ECO/GEAR button again, change the mode, or set the temperature below 24°C/75°F. For insufficient cooling, ensure the set temperature is 24°C/75°F or above.

GEAR operation

Select GEAR operation: 75% (up to 75% energy consumption) → 50% (up to 50% energy consumption) → Previous setting.

The set temperature will revert to normal after 3 seconds.

Turbo function

In COOL mode, Turbo provides the strongest fan speed for rapid cooling.

In HEAT mode, Turbo provides the strongest fan speed for rapid heating.

SET function

Press SET to enter the function menu, then press SET again to select a function. The selected symbol will flash; press OK to confirm.

To cancel, repeat the same steps.

Functions cycle as: Fresh/UV lamp → Breeze Away → Follow Me → Active Clean → AP mode.

Fresh/UV lamp function

Activates the FRESH function, which includes an ionizer and/or UVC lamp for air purification.

Breeze Away function

This feature directs airflow away from the user for a gentle cooling sensation. Available in Cool, Fan, and Dry modes.

Follow Me function

The remote measures the ambient temperature and sends it to the air conditioner every 3 minutes. This helps optimize room temperature for comfort, especially in AUTO, COOL, or HEAT modes. Press and hold Turbo for 7 seconds to activate/deactivate the memory feature. "On" or "Off" will display for 3 seconds. The Follow Me function remains active through mode changes, power on/off, or power failure.

Active Clean function

This technology removes dust and mold that cause odors. It rapidly freezes and thaws the heat exchanger to clean adhered material. The display shows "CL" when active. The function runs for 20-130 minutes (model dependent) and then automatically turns off.

AP function

Use AP mode for wireless network configuration. For some units, pressing SET may not work. To enter AP mode, press the LED button 7 times within 10 seconds.

Contact Information and Disclaimers

All images are for illustrative purposes only. Actual product may differ slightly in shape, but functions remain the same. The company is not responsible for typographical errors. Design and specifications are subject to change without prior notice for product improvement.

For details, contact the manufacturer at +30 211 300 3300 or the sales agency. Manual updates will be available on the manufacturer's website. Please check for the latest version.

Scan the QR code to download the latest version of this manual.

www.inventorairconditioner.com/media-library