boAt Airdopes 402

Introduction

Welcome to the boAt Airdopes 402. This manual serves as your guide to understanding and operating your new wireless earbuds. Familiarity with Bluetooth and device connection is key to enjoying your audio experience. We strongly advise that this manual is thoroughly read before beginning use, and referred to when in times of difficulty. Let's get ready to Plug Into Nirvana!

In the Box

• 1x boAt Airdopes 402
• 1x Charging Case
• 1x USB charging cable
• 2x pairs of additional earmuffs (Small & Large)
• 1x User Manual

Product Overview

Key Components:

• 1. Capacitive Touch Control (CTC): Touch-sensitive area on the earbuds for controls.
• 2. Indicator Light: LED on the earbud showing status.
• 3. Charging Contact Point: Connects to the charging case.
• 4. Charging Case Indicator: LEDs on the case showing battery status.
• 5. Micro USB Charging Port: Port on the case for charging.

Power ON

Automatic Power ON:

1. Take both earbuds out of the Charging Case.
2. Wait for the earbuds to automatically pair with each other. They enter connection mode, indicated by alternate Blue/Red LEDs.

Manual Power ON:

If earbuds do not power on automatically, long-press the CTC on either earbud for 3 seconds. Blue/Red LEDs will blink.

Note: Both earbuds are master earbuds. Pairing mode lasts for 5 minutes. If missed, reconnect and repeat the procedure. Airdopes 402 remembers previously connected devices and reconnects automatically.

Connection Mode

1. Turn on Bluetooth on your device and scan for devices.
2. Search for 'Airdopes 402' and pair. Enter '0000' as the passkey if prompted.
3. Congratulations! Your Airdopes 402 is now connected and ready for use.

Note: Bluetooth version V5.0.

LED Indicators

Earbud LEDs:

• Voice Assistant: Long press CTC for 2 seconds.
• Manual Power ON: Long press CTC for 3 seconds (Blue/Red LEDs blink).
• Manual Power OFF: Long press CTC for 5 seconds (Red LED).
• Factory Reset: When powered off and in case, long press CTC on both earbuds for 8 seconds (Red and Blue LEDs).

Single Earbud Use

To use a single earbud:

1. Ensure both earbuds are in stereo mode and connected to your device.
2. Remove either the left or right earbud from your ear.
3. Place the removed earbud back into the Charging Case.
4. You are now using the remaining earbud in mono/solo mode.

Note: Both earbuds are master earbuds, allowing single earbud use with either. To switch back to stereo, simply take out the earbud kept in the case; it will automatically power on and pair.

Basic Functions

• Voice Assistant: Long press CTC for 2 seconds to activate Google/Siri.
• Answer/Hang up call: Tap CTC once.
• Reject call: Long press CTC for 1.5 seconds.
• Play/Pause: Tap CTC on either earbud.
• Next Track: Double tap the right earbud's CTC.
• Previous Track: Double tap the left earbud's CTC.

Note: Volume cannot be controlled via earbuds; adjust volume on your device.

Charge The Earbuds

• Place the earbuds into the charging case in their correct orientation.
• A red light on the earbuds indicates charging.
• A blue light indicates full charge; this light will turn off once fully charged.
• The charging case powers off automatically to save power when earbuds are fully charged.

Charge The Case

Warning: Do not charge the carrying case with "9V" or "12V" output adapters, as this may cause damage. Charge only according to specified norms (not more than 5V 2A).

• Connect the provided USB cable to any USB port (e.g., wall adapter, computer) to charge the case.
• The 4 horizontal LEDs on the case indicate the charge/battery status.
• The case is fully charged when all 4 lights are illuminated.

Smart Power Off

After use, remove earbuds from ears, place them back inside the case in the correct orientation, and close the lid to power them off. The LED will indicate charging.

Manual Power Off

When in standby state, long-press the CTC on either earbud for 5 seconds to manually power off both earbuds. Place them back into the charging case to charge.

Factory Reset / Troubleshooting

Perform these steps if you encounter difficulties with your Airdopes 402.

Performing a Reset:

1. Place both earbuds inside the charging case in their correct orientation.
2. Long-press the CTC on both earbuds for up to 8 seconds. Alternate red and blue LED flashes indicate the reset is complete.
3. Close and then reopen the case lid.
4. Take the earbuds out; they will restart automatically.

Common Problems & Solutions:

Specifications

Cautions

• Avoid contact with sharp edges, uneven surfaces, and metal parts to prevent damage.
• Do not dismantle the product; this can lead to fire, electrical breakdown, or damage. Servicing should only be done by qualified providers.
• Do not remove the battery yourself. Replacement by a service provider/manufacturer is recommended to avoid fire or electrical hazards.
• Clean earbuds with a damp, soft cloth only. Avoid oily volatile liquids and extreme temperatures.
• To protect hearing, use an appropriate volume level. Gradually increase volume to a comfortable level. Exposure to noise above 85 dB can cause hearing loss.
• Damage not caused by manufacturing defects will void the warranty. Handle earbuds with care.
• Do not use earbuds when unsafe, such as while operating a vehicle or crossing streets, where full awareness of surroundings is required.

Charging Norms & Precautionary Guidelines

Recommended Specifications:

• Charger/Brick/Adapter: 5V 2A
• Cable/Wire: Standard Cable (35 strands @0.10mm diameter/strand)

Any other accessory can be paired if its specifications meet the above norms.