HUANANZHI X58 DELUXE User Manual

Safety Information

Products can be damaged by electrostatic discharge (ESD). Please observe the following precautions to ensure successful computer assembly:

• To prevent static electricity from damaging the motherboard when handling it, release your static electricity by touching other metal objects before handling the motherboard.
• When picking up the motherboard, hold it by its edges to avoid touching sensitive components.
• When the motherboard is not installed, place it on an antistatic mat or static shielding container.
• Before opening the computer, ensure there are no loose screws or metal components on the motherboard or anywhere else inside the computer case.
• Do not start the computer until the installation is complete. Failure to do so may result in permanent damage to components and injury to the user.
• If you need help during any installation step, please consult professional after-sales customer service staff.
• Before installing or removing any computer components, turn off the power and unplug the power cord from the socket.
• Keep this motherboard away from moisture.
• Keep this User Guide for future reference.
• Before connecting the power supply to an electrical outlet, ensure your outlet provides the same voltage as indicated on the power supply.
• Place the power cord where it will not be stepped on by others and do not place anything on top of it.
• If liquid has penetrated into the computer, the motherboard is exposed to moisture, the motherboard does not work, or you cannot get it to work after following the instructions, the motherboard has been dropped and damaged, or the motherboard has obvious signs of damage, please send the motherboard to maintenance personnel for inspection.

Packaging

Please make sure that the motherboard packaging you purchased is intact. If the packaging is damaged or any accessories are damaged or missing, please contact HUANANZHI as soon as possible.

Package Contents:

• 1 x HUANANZHI X58 DELUXE Motherboard
• 1 x SATA data cable
• 1 x I/O shield back plate
• 1 x User manual
• 1 x Warranty card

Features

• CPU Support: Intel® LGA1366 processor (Intel® Xeon™ / Intel® Core™ i7 1st generation)
• RAM: 3 x DIMM slots, maximum support 48GB DDR3 1600/1333MHz Non-ECC/ECC memory. Triple-channel memory architecture. (Actual memory data rate depends on CPU type and DRAM module.)
• I/O Ports:
  • 6 x SATA2.0 (maximum transfer speed up to 2GB/s)
  • 6 x USB2.0 interface
  • 2 x USB3.0 interface
  • 1 x PS/2 keyboard and mouse port
  • 1 x RJ45 Gigabit LAN interface
• Audio: Realtek Audio Codec, Realtek 5.1 channel high-definition audio. Audio source output: Front output / front speaker output. Audio source input: Mic in, audio in.
• Expansion Slots:
  • 2 x PCIe 2.0 x16
  • 1 x PCIe x1
  • 1 x PCI

Motherboard Diagram

The motherboard features the following key components:

• CPU Socket (LGA1366)
• DDR3 DIMM Slots (3x)
• 8P CPU Power Supply Interface
• 24P Motherboard Power Supply Interface
• PCI-E x16 Interfaces (2x)
• PCI-E x1 Interface (1x)
• PCI Interface (1x)
• SATA2.0 Ports
• 3-Pin Fan Connectors (multiple)
• 4-Pin Fan Connector
• PS/2 Keyboard/Mouse Port
• USB 3.0 Ports
• USB 2.0 Ports
• Gigabit Ethernet Port
• Audio Interface
• Front Panel Connectors (F_PANEL1) including Power SW, Reset SW, HDD LED, Power LED.

Rear I/O Panel

The rear I/O panel includes:

• PS/2 Keyboard/Mouse Port
• USB 2.0 Ports
• USB 2.0 / USB 3.0 Ports
• Gigabit LAN Port
• Audio Ports (Line in, Line out, Microphone in)

LAN Port Status Table

The LAN port has indicator lights:

• Connection/Work Light: Off (Network not connected), Yellow (Network connected), Flashing (Network data in use)
• Speed Light: Off (Transmission rate 10 Mbps), Green (Transmission rate 100 Mbps), Orange (Transmission rate 1 Gbps)

Audio Port Configuration

The audio ports are configured as follows:

• Audio Port (likely Line Out)
• Audio Input (likely Line In)
• Audio Output / Front Speaker Output
• Microphone Input

Installation and Setup

Notice

Please check the motherboard carefully. All pins marked with "1" or thick white lines are Pin 1.

CPU Installation

To correctly place the CPU in the motherboard, align the golden triangle indicator on the LGA1366 CPU with Pin 1 on the socket.

Memory Installation

1. Pull the clips at both ends of the memory slot outwards.
2. Match the protruding position of the memory stick with the slot to determine the installation direction.
3. Align the memory stick with the slot and press it down firmly.
4. The clips at both ends of the slot should pop up automatically, securing the memory.

Graphics Card Installation

1. Use a screwdriver to remove the bezel and screws on the main unit's expansion slot cover.
2. Lift the retention clip of the graphics card slot.
3. Insert the graphics card into the appropriate PCI-E x16 slot.
4. Ensure the card is fully seated; the retention clip should automatically return to its original position.
5. Secure the graphics card to the chassis with screws.
6. Install the power cord to the graphics card if required.

SATA Interface Connection

Connect SATA devices using SATA data cables to the SATA2.0 ports on the motherboard.

Front Panel Connectors (F_PANEL1)

Connect the front panel headers for power button, reset button, HDD LED, and power LED according to the pinout diagram.

Clear CMOS Jumper

Locate the Clear CMOS jumper on the motherboard to reset BIOS settings to default values.

Driver Installation

Ensure you have the correct drivers for your operating system (Windows 7/10).

Driver Listing:

• X58 Chipset Driver: Intel Chipset Information Installation
• X58 Sound Card Driver: Realtek series sound card driver installation
• X58 LAN Driver: Realtek Gigabit LAN Installation

Intel Chip Information Installation:

1. Navigate to Control Panel > System > Hardware > Device Manager.
2. Right-click the hardware device needing a driver update.
3. Select "Update Driver". Choose "Do not connect to the Internet" and then "Manual Installation".
4. Browse to the directory containing the driver files and select "Next".

Audio Driver Installation:

Identify the audio chip model on the motherboard (refer to the manual) and select the corresponding driver.

1. Installation (HD Audio): Run the installer (e.g., WDW-267 for XP, or from the VISTA-WIN7-R267 directory). Follow the on-screen prompts to "Next" and "Finish". The system will restart to complete the installation.
2. Uninstallation (HD Audio): Go to Windows Desktop > Settings > Control Panel > Add/Remove Programs. Select "Realtek High Definition Audio Driver" and click "Add/Remove".

External Graphics Card Driver Installation:

1. Run the setup.exe file from the graphics card driver directory.
2. Follow the prompts: "Next" > "Yes" > "Next" > "Next" > "Finished". The system will automatically detect and install the devices.

Network Card Driver Installation:

1. Run the driver installer from the X58 LAN DRIVER/WIN7 XP directory.
2. Click "Next" > "Install" > "Finished". Restart the computer. The system will automatically detect and install the devices.

BIOS Settings

The CMOS SETUP utility stores motherboard configuration data. To enter the BIOS setup:

• When the computer starts POST (Power On Self Test), press the Delete key.
• The motherboard warm boot key is F7.

Menu Navigation: A triangle indicator (Δ) on the left of a menu item signifies a submenu; selecting it will display the submenu.

Main Menu Functions:

• Main: System Overview (System Information) - Displays current time, hard disk specifications, and display type.
• Advanced: Advanced Settings - Configure special BIOS functions like virus warnings and boot disk priority.
• Chipset: Advanced Chipset Settings - Configure advanced chipset functions.
• Boot: Boot Settings - Configure boot device priority and other boot-related options.
• Security: Security Settings - Set BIOS passwords.
• Save: Save Settings - Save current BIOS configuration.
• Exit: Exit Options - Includes options to load optimized defaults, load fail-safe defaults, discard changes, or exit without saving.

Directory

This manual is organized as follows:

• Safety Precautions
• Packing
• Brief Introduction
• Motherboard Diagram
• Rear I/O Panel
• Installation and Settings
• Drivers Installation
• BIOS Settings