Milesight AI TrueColor Turret Network Camera

1. Package Contents

• Milesight AI TrueColor Turret Network Camera x 1
• Expansion Screw Packet x 1
• Screwdriver x 1
• Water-proof Connector x 1
• Quick Start Guide x 1
• Warranty Card x 1
• Perforation-assisted Sticker x 1

2. Hardware Overview

Smart Hybrid Lights: Mixed IR and White Warm Lights

Lens

Flashing Red Light

Flashing Blue Light

Audio In/Out (Optional)

DC 12V

Ethernet Port (PoE)

Horizontal Limit Screw

Alarm In/Out (Optional)

Microphone

Vertical Limit Screw

3. Dimensions

AI TrueColor Turret Network Camera

Units: mm

Dimensions:

• Height: 108 mm
• Diameter: 84 mm
• Width: 80 mm
• Mounting Hole Diameter: ø4.2 mm
• Base Diameter: 84 mm
• Overall Width: 122 mm
• Mounting Bracket Width: 46 mm

4. Installation

Step 1: Fix the perforation-assisted sticker at the camera's intended installation position, then punch holes as indicated on the sticker.

Step 2: Fix the mounting bracket on the position by using the screws. Available mounting options include Wall Mount (A72 V2 & A71), Junction Box (A84), and Pendant Mount (A76 V2).

Step 3: Pass the tail cable of the device port into the mounting bracket. If there is no hole in the wall, pull the tail cable out from the side before installing the mounting bracket. Remove the plug from the slot and ensure the tail cable is in the side wire trough before tightening the mounting bracket screws.

Step 4: Rotate the camera unit to detach the camera mounting bracket.

Step 5: After attaching the camera to the mounting bracket, tighten the horizontal limit screw.

Step 6: Adjust the camera position by loosening the vertical limit screw and rotating the camera to match the scene. The camera offers adjustable ranges: horizontal pan 0° to 360°, vertical tilt 0° to 90°, and overall rotation 0° to 360°.

Step 7: Finish the installation.

5. How to Connect to Alarm Interface

The General I/O Terminal Block has four pins:

• PIN1: Alarm Output NC/NO 24V DC 1A
• PIN2: Alarm Output NC/NO 24V DC 1A
• PIN3: Alarm Input NC/NO ≤ 12V
• PIN4: Alarm Input NC/NO ≤ 12V

6. How to Connect the Water-proof Connector

Follow these steps to ensure a secure and waterproof connection:

1. Get the network cable through the screw nut, rubber ring, and the screw bolt.
2. Insert the rubber ring into the screw bolt.
3. Connect the screw nut to the screw bolt.
4. Place the O-Ring on the network port connector.
5. Connect the RJ45 to the network port connector and tighten the screw bolt and the connector.

Note: Tightly wrap all cable-out interfaces with adhesive tape at the end to prevent water ingress.

7. Assigning an IP Address by Using Smart Tools

Milesight Smart Tools is a software utility for detecting, configuring IP addresses, and managing firmware upgrades for Milesight network cameras on a LAN. It is recommended for managing multiple cameras.

Steps:

1. Launch Smart Tools and navigate to the IPC Tools page. Enter device information (IP address, MAC address, Port number, Netmask, Gateway) to display compatible Milesight network cameras in the network.
2. Select the camera(s) by MAC address.
3. Click "Activate" to set a password (8-32 characters, including at least one number and one letter) and three security questions for initial use.
4. Enter the username and password, then modify the IP address or other network settings by clicking "Modify".
5. Access the camera via a web browser by double-clicking the selected camera in the tool or by entering its IP address in your browser.

For detailed instructions, refer to the "Smart Tools User Manual".

8. Assigning an IP Address via Browser

If your computer's network segment differs from the camera's, configure your PC with an IP address in the same subnet (e.g., 192.168.5.xx with a subnet mask of 255.255.255.0) to establish access. Refer to the "Milesight Network Camera Quick Start" for more details.

9. Accessing from the Web Browser

The camera is compatible with most standard operating systems and browsers, including Internet Explorer, Firefox, Chrome, and Safari. For information on plugin installation, consult the troubleshooting guides:

• Milesight-Troubleshooting-Plugin Installation on Windows-IPC
• Milesight-Troubleshooting-Plugin Installation on MAC

10. FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.