IPEVO AI WIRELESS MIC DUO
User Guide and Product Information
Transmitter
Introduction
The transmitter is a key component for audio pickup. It features:
- Back clip: For attaching the transmitter.
- Status indicator: Shows connection and battery status.
- Pickup microphone: Captures audio.
- Power switch: Turns the device on/off.
- Noise reduction switch: Activates/deactivates AI noise reduction.
- Three-level adjustment of pickup volume: Controls audio input sensitivity.
- 3.5mm audio output port: For connecting to other devices.
- USB-C charging port: For charging the device.
Transmitter Status Indicator
- Green light on: Wirelessly connected to the receiver.
- Flashing green light: Wireless connection with the receiver has been disconnected.
- Flashing red light: Low battery prompt during use.
- Red light on: Charging when turned off.
- Red light goes out: Charging complete when shut down.
Receiver
Introduction
The receiver processes the audio signal and connects to recording devices. It features:
- Display: Shows status and settings.
- USB-C data port: For connecting to computers or other devices.
- Power switch: Turns the device on/off.
Receiver Display
The receiver display provides information on:
- No. 1 transmitter display area.
- Receiver battery three-level power display.
- AI noise reduction status for transmitter No. 2 (displayed when on).
- Three-level display of pickup volume for transmitter No. 2.
- Four levels of real-time volume display for transmitter No. 2.
- Three levels of battery power display for transmitter No. 2.
Charging and Power
It is recommended to fully charge the device before use. A full charge can last up to 18 hours, depending on usage.
When the battery is low, the receiver will show one bar of power remaining, and the transmitter's red light will flash. Please charge the device promptly.
Charging requires a USB-A interface 5V/1A power supply that complies with safety certification. Standard accessories include USB-A to three USB-C charging cables.
Connections
Connecting to a Computer
Connect the receiver to a PC using a USB-A to Type-C female connector.
Connecting to a Mobile Phone
For Android phones, use a standard Type-C data cable. For iPhones, use a Type-C data cable along with a Type-C female to Lightning adapter.
Connecting to a Camera
Connect the receiver to a camera using a three-pole 3.5mm dual-plug audio cable. The receiver clip can be mounted on the camera's hot shoe mount.
Wireless Connection and Operation
Pairing and Powering On
To power on, long press the power button on the transmitter. The screen will display. To power on the receiver, long press its power button; the indicator light will turn green when wirelessly connected.
Transmitter Functions
- Status Indicator: Green light indicates a wireless connection to the receiver.
- Noise Reduction: Short press the noise reduction button to turn the AI noise reduction function on or off.
- Pickup Volume: Short press the pickup volume button to cycle through three levels of audio pickup volume.
Usage Scenarios
The system captures audio via the transmitter and wirelessly transmits it to the receiver. The receiver outputs analog audio signals through its 3.5mm audio interface to mobile phones, cameras, and other live broadcasting and recording equipment. It functions as an external wireless microphone for high-definition sound quality.
For outdoor live broadcasts where wind noise and other ambient sounds can affect pickup quality, it is recommended to install the included windproof cover and enable the AI noise reduction function to improve voice clarity. For indoor use, or when playing music, it is recommended to turn off the AI noise reduction function to enhance the range of audio collection.
Regulatory Compliance
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
ISED Statement (Canada)
English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
French: This device contains license-exempt transmitters/receivers that comply with Innovation, Science and Economic Development Canada's license-exempt CNR(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
This device meets the exemption from the routine evaluation limits in section 2.5 of CNR 102 and compliance with RSS 102 RF exposure; users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits for an uncontrolled environment. This equipment should be installed and used with a minimum distance of 0 cm between the radiator and your body.
