SolaX EV-Charger 7.2 kW-22 kW Quick Installation Guide

Packing List

• EV-Charger *1
• EV-Charger User Manual 7.2 kW - 22 kW
• Manual *1
• Expansion bolt *3/5 (3 for type S, 5 for type P)
• Self tapping screw *3/5 (3 for type S, 5 for type P)
• Gasket *3/5 (3 for type S, 5 for type P)
• Quick Installation Guide *1
• European terminal *3/5 (3 for single-phase; 5 for three-phase)
• RJ 45 terminal adapter *1
• RFID Card *2
• CT (single-phase) *1
• CT (three-phase) *1
• Cable hook *1 (only for type P)

Installation Steps

1. Remove the screw from the EV-Charger with the cross screwdriver. Then remove the back bracket carefully.
2. Fix the back bracket and the cable hook (only for type P) to the wall.
   
   • Mark the position of the holes.
   • Drill holes with a ⌀ 8 drill.
   • Depth: at least 45 mm.
   • Insert the expansion bolts.
   • Align the bracket and the cable hook (only for type P) with the holes, and screw the self-tapping screws with the cross screwdriver. (Torque: 1.5~2 N·m)
3. Hang the EV-Charger on the wall for trial, then estimate the required length of input cable (three-core for single-phase, five-core for three-phase, outer diameter: 12.5-18 mm) and communication cable. After that, take the EV-Charger down.
4. Unscrew the EV-Charger's rear cover with the cross screwdriver and take it down. Then undo the fastening heads and take the waterproof materials away.
5. Unscrew the countersunk screw of the base plate of the communication board with the cross screwdriver. Then pull the base plate of the communication board out.
6. Insert the prepared communication cable through the waterproof connector in sequence. If the cable is self-made, insert the wires into the RJ45 terminals and then use crimping pliers to press them tightly.
7. Strip the outer sheath of the input cable for a length of 60-70 mm, ensuring all wires reach the terminal blocks with a little excess length. Strip approximately 12 mm of insulation from the end of all colored wires. Crimp the European terminal with the wire crimper.
8. Insert the input cable through the waterproof connector in sequence.
9. Insert the wires into the appropriate holes of the terminal blocks, then secure the terminals with a straight screwdriver.
10. Press the spring upward and push the base plate of the communication board in. Then screw the countersunk screw.
11. Push the rear cover to the appropriate position of the cables and screw the self-tapping screws with the cross screwdriver. Then tighten the waterproof fastening head. (Torque: 2~2.5 N·m)
12. Hang the EV-Charger up carefully and steady the EV-Charger with the self-tapping screw and the cross screwdriver. For type P, connect the charging connector with the EV-Charger and hang the connecting cable on the hook. (Torque: 2~2.5 N·m)

CT & WiFi Connection

CT Connection

Diagram: A diagram shows a PV array connected to an inverter, which connects to an AC distribution box. From the AC distribution box, a CT is connected to an electricity meter and then to the EV-Charger. Another line from the AC distribution box goes to 'other home Load'. A close-up of the CT shows an arrow indicating it must point towards the public grid. The CT is placed on the L line, with the public grid electricity on the other side. Notes indicate not to place the CT on the N or PE wire, on non-insulated wires, or on both N and L wires simultaneously. For three-phase CTs, clip them on the corresponding phases.

WiFi Connection

1. Use your smartphone to scan the QR code or search for "SolaXCloud" in a browser to download the Monitoring App.
2. Create a new account on the Monitoring App.
3. Login and navigate to the Account page in the app. Click "Wi-Fi Connection" and follow the instructions to complete the process.