Installation Guide for ZKTeco models including: U1000E, U1000F, U2000E, U2000F, U1000E Long Distance RFID Access Control, U1000E, Long Distance RFID Access Control, Distance RFID Access Control, RFID Access Control, Access Control, Control
ZKTeco U1000E Long distance RFID Access Control - The Security Mill
Installation Guide UHF RFID Integrated Machine: U1000E, U1000F, U2000E, U2000F Version: 1.0 Date: 2017.09
Installation Guide UHF RFID Integrated Machine: U1000E, U1000F, U2000E, U2000F Version: 1.0 Date: 2017.09 1. Overview Front View Antenna Working Frequency: 902MHz 928MHz 865MHz 868MHz Read Range: U1000E/F (0-6 meters) U2000E/F (0-12 meters) Dimension 250mm*250mm*70mm (U1000E, U1000F) 445mm*445mm*70mm (U2000E, U2000F) Lateral View and Interface Mounting Bracket Cables Cables Cable Definition: 6PIN Green 6PIN Black 4PIN Green 2PIN 4PIN Green 4PIN Black RJ45 6PIN Green 6PIN Black USB 4PIN Black 1 2. Install the Integrated Machine 1) Hang Mounting Please install the integrated machine according to the following chart. The machine is installed on the fixed column, and the angle and height is adjusted according to the actual effect of swing card. Method A: Method B: Note: To get better reading performance, driving direction of vehicle should face to the UHF integrated machine. 2) Ceiling Mounting Please install the integrated machine vertically on the ceiling. We recommend the installation height from the ground is no more than 4 meters in order to better identify effect. 2 Note: 1) Avoid installing the integrated machine against to another. 2) The integrated machine detection distance may vary depending on rain, snow or wind. 3) The device should be away from strong magnetic field when working. 3. Install the UHF Card 1) Tag1, DF01Card, DF02Card UHF1-Tag1, DF01Card and DF02 Card are generally used in long distance access control management and long distance pedestrian crossing control management. 3 2) Tag2 Card UHF1-Tag2 is generally used in long distance pedestrian crossing control management, such as long distance single channel access management in construction site. 3) Tag3 Card UHF1-Tag3 is generally used in long distance fixed vehicle access management. It is installed on the upper or lower edges of the license plate. As is shown below: 4) Tag4 Card UHF1-Tag4 is also generally used in long distance fixed vehicle access management. It is pasted on the interior windshield of car. The distance between the UHF tag and the metal frame shall be 80 mm at least. 4 The position of the tag/card in the vehicle is as follows: Note: If there is a metal explosion-proof film above the windshield, you have to cut a small piece off it or roll down the window to read the tag. (The cut area is at least one time the tag's) 4. Structure Function UHF Tag 5 (1)If a registered user verified, the device will export the signal to unlock the door. (2)Door sensor will detect the on-off state. (3) External exit button is supported; it is convenient to open the door inside. (4) External card reader is supported. (5) Connect the USB port of the integrated machine to the USB port of the computer to set the working parameters of the integrated machine. (6) Supports TCP/IP modes to connect with PC. 5. Lock Connection 1) Shares power with the lock: ULOCK=12V, I IDevice + ILock (The maximum operating current of device is 100mA, and the rated current is 60mA); and the lock is near to the device. 2) Does not share power with the lock: When ULOCK=12V, I < IDevice + ILock (The maximum operating current of device is 100mA, and the rated current is 60mA); When ULOCK12V; When the lock is far from the device. 6 (1) The system supports NO LOCK and NC LOCK. The NO LOCK (normally open by power on) is connected with NO terminal, and the NC LOCK is connected with NC terminal. (2) To prevent the generation of self-inductance EMF which would affect the system, when the electrical lock is linked to the Access Control System, it is required to connect one FR107 diode (equipped in the package, do not reverse the polarities) in parallel in order to release the self-inductance EMF. 6. Barrier Connection 7. Connected with other parts 7 8. Connected with Power 9. Wiegand Output & Input 1) Wiegand Output Input DC12V, 110mA (80mA standby) Positive is connected with +12V, negative is connected with GND (do not reverse the polarities). The device supports standard Wiegand 26/34 output, as a reader device it has a very good compatibility. 2) Wiegand Input The device has the function of Wiegand signal input. It supports to connect with an independent card reader. They are installed each side of the door, to control the lock and access together. Note: (1) Please keep the distance between the device and Access Control or Card Reader less than 90 meters (Please use Wiegand signal extender in long distance or interference environment). (2) To keep the stability of Wiegand signal, connect the device and the Access Control or Card Reader in same `GND' in any case. 8 10. Connected with Computer 1) USB Connection Integrated Machine Connect the USB port of the integrated machine to the USB port of the computer. Set the working parameters of the integrated machine using DEMO software. 2) RJ45 Connection Connect the RJ45 port of the integrated machine to the Ethernet port of the computer. The machine supports access to ZKAccess 3.5 and ZKBioSecurity 3.0. 9 10GPL Ghostscript 9.55.0