MOES MS-104CZ ZigBee Smart Switch Module: Installation, Features, and Setup Guide
Brand: MOES
Model: MS-104CZ / ZM-104C
Product Description
The MOES MS-104CZ is a ZigBee smart module switch designed for intelligent home automation. It connects to a ZigBee gateway hub and allows for remote control, timing, scene linkage, and voice control via mobile apps and voice assistants like Amazon Alexa and Google Home.
Technical Specifications
| Product Type | Smart Switch Module |
|---|---|
| Voltage | 90-250V AC 50/60Hz |
| Current | Total 10A |
| Wireless Protocol | ZigBee 3.0 |
| Operation Temperature | -10ºC - +40ºC |
| Case Temperature | Tc: +80ºC (Max.) |
| Operation Range | ≤200 m |
| Dimensions (WxDxH) | 52x47x22 mm |
| IP Rating | IP20 |
| Frequency Band | 2.400-2.483GHz |
| Max Radio Transmit Power | <+10dBm |
| RoHS Standard | 2011/65/EU, (EU) 2015/683 |
Installation
Warnings
- Installation must be performed by a qualified electrician according to local regulations.
- This device requires a ZigBee gateway hub.
- Keep the device away from children, water, damp, or hot environments.
- Avoid installing near strong signal sources like microwave ovens to prevent signal interruption.
- Obstructions like concrete walls or metallic materials can reduce the effective range and should be avoided.
- Do not attempt to disassemble, repair, or modify the device.
Wiring Instructions
- Turn off the power supply before any electrical installation work.
- Connect wires according to the wiring diagram.
- Insert the module into the junction box.
- Connect the power supply and follow configuration instructions.
Wiring Configurations
The module can be wired with different types of switches and sockets:
- With one 3-Gang switch: Connect Line (L) and Neutral (N) to the module. Switches S1, S2, S3 connect to the respective loads.
- With 3-Gang 2-Way switches: Similar wiring to the 3-Gang switch, accommodating 2-way switch functionality.
- With wall socket (3 sockets available): The module can control up to three sockets. Connect L and N to the module.
Note: Ensure the power supply is off and verify with an electrical tester before wiring.
Removing the Old Switch
- Turn off the circuit breaker and test for power.
- Remove the old switch's faceplate.
- Carefully remove the old switch and identify Line/Load wires (wire colors may vary).
- Ensure all wires are de-energized before proceeding.
Preparation for Use
1. Download and Install MOES App
Download the MOES App. While compatible with Tuya Smart/Smart Life apps, the MOES App is recommended for enhanced features and Siri integration.
2. Register or Log In
Open the MOES App. Tap "Register" to create an account using your phone number and set a password, or "Log in" if you already have an account.
3. Add Device
Ensure your MOES App is connected to a ZigBee gateway.
Method One: Network Configuration Guide
Scan the QR code provided in the app or documentation to configure the network.
Method Two: Reset and Add
- Ensure your MOES App is connected to a ZigBee gateway.
- Reset the device:
- Push wall switch (Reset switch): Press the switch button 10 times until continuous beeps are heard.
- Rocker light switch: Press the switch button 20 times (ON/OFF cycle 10 times) until continuous beeps are heard.
- Module reset button: Long press the button on the module until "Di-Di" sounds (2 times), then long press again for continuous beeps.
- Enter the gateway interface in the app. Follow the on-screen prompts to "Add sub-device". The LED should blink. Connection typically takes 10-120 seconds.
- Once added successfully, you can edit the device name and click "Done" to enter the device page.
How to Achieve Multi-Control Association
This feature allows multiple switches to control the same light.
- Ensure you have added a smart switch to your Smart Life/Tuya App (or MOES App). If a switch is already added, proceed to the next step.
- Wire only L and N to the new switch; no connection to the light is needed for association.
- In the app, select the main switch.
- Navigate to the multi-control association settings (usually via a '+' icon or similar in the top right corner).
- Choose the switch you want to associate and select the specific button on that switch to control the light.
- Confirm the association. The associated switch should be enabled in the app.
- You can now control the light with multiple switches. Repeat steps for additional switches.
Voice Control
This device is compatible with Amazon Alexa and Google Home. For detailed setup instructions, visit: https://www.moestech.com/blogs/news/smart-device-linked-voice-speaker
Troubleshooting
For installation or operation issues, consult the product data sheet at: https://www.moestech.com/blogs/news/zm-104c
Declaration of Conformity
WENZHOU NOVA NEW ENERGY CO., LTD declares that the radio equipment type ZM-104C complies with EU Directives 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at: https://www.moestech.com/blogs/news/zm-104c
Service and Warranty
MOES offers a two-year worry-free after-sales service. For service or questions, contact the distributor or MOES support. Warranty terms apply, excluding damage from personal reasons or unauthorized modifications.
Recycling Information
Dispose of this product separately from unsorted municipal waste according to the WEEE Directive (2012/19/EU). Contact local authorities or installers for collection point information.
