ILIFE T60s AI Robot Vacuum Cleaner with Self-Sufficient Station

Welcome

Dear Customer,

Thank you for purchasing the ILIFE T60s robotic vacuum cleaner! You've joined millions of people who clean with robots – the smarter way to get it done.

Please take a few moments to read this manual and get acquainted with your robot to achieve the best performance. If you have any problems, do not hesitate to contact customer service or visit our website at www.iliferobot.com for more information.

Stay connected with us on "X" to enjoy exclusive benefits:

• Get support tailored to your specific robot, including answers to questions, maintenance tips, video demos, live chat, and more.
• Get product updates and valuable information, and be among the first to find out about new robots, exclusive discounts, and special promotions.

Connect with us right now at X: https://x.com/ilife_Global

Enjoy a thorough cleaning every day!

Best regards,
ILIFE Innovation

ILIFE Customer Service
support@iliferobot.com

Table of Contents

• Safety Precaution
• Product Composition
• Installation
• APP Connection
• How To Use
• Routine Maintenance
• Product Specification
• Common Problems
• Troubleshooting

Safety Precaution

Use Restrictions

• This product is only for floor cleaning in home environments. Do not use it outdoors, in non-floor, commercial, or industrial environments.
• This product is not intended for use by persons with physical, sensory, or intellectual disabilities, or persons without relevant experience and knowledge, including children, unless under the supervision or guidance of a guardian to ensure their safe use.
• Do not let children use the mopping robot as a toy. Supervise children and pets, and keep them away when the main unit is working.
• If the power cord is damaged, it must be replaced with a dedicated cord or a component purchased from the manufacturer or service department.
• Do not place children, pets, or any objects on the stationary or running robot.
• Do not place the cleaning brush in an area accessible to children.
• Do not lift the LiDAR protective cover directly when moving the robot.
• Do not use it in a suspended environment (such as duplex floors, open balconies, and the top of furniture) without guidance.
• Do not use it in environments higher than 35°C, lower than 0°C, or with any liquid and viscous substances on the ground.
• Do not use to sweep any burning objects.
• Before use, tidy up the ground wire at home. Using it on a power line is dangerous.
• Please put away fragile items and sundries on the ground (such as vases, plastic bags, etc.) to prevent the robot from being blocked or colliding with valuables.
• Do not use mopping mode on carpet. When mopping, set up a virtual wall or restricted area in the carpet area.
• Do not let the robot pick up hard or sharp objects (such as decoration waste, glass, iron nails, etc.).
• Turn off and unplug the main unit and station before cleaning and maintenance.
• Do not place the main unit upside down on the ground for a long time.
• If you need to transport the product, ensure the robot is turned off. Use the original packaging box for packaging protection.
• Do not use a damp cloth or any liquid to wash the main unit and station.
• After daily cleaning of washable parts, dry them thoroughly before installing and using them.
• During the cleaning process, do not move the sweeping robot out of the station to avoid equipment damage.
• Use this product in accordance with the instructions in the manual.
• Any loss and injury caused by improper use shall be borne by the user.
• Do not use in direct sunlight.
• This equipment should be installed and operated with a minimum distance of 20cm between the antenna and your body.
• Frequency bands: Bluetooth 2402-2480 MHz, Wi-Fi 2412-2472 MHz.
• Maximum radio-frequency power transmitted: Bluetooth <10dbm (EIRP), Wi-Fi <20dbm (EIRP).

Battery and charging

• Do not use third-party batteries, power cords, or stations. Only use with stations of model T60s.
• Do not disassemble, repair, or modify the battery or station without permission.
• Do not wipe or clean the battery connector of the station with a damp cloth or wet hands.
• Do not place the station near heat sources (such as radiators, etc.).
• Do not throw away discarded batteries. Hand them over to a professional recycling organization.
• If you do not use it for a long time, turn off the robot after fully charged and store it in a cool, dry place.
• Charge the battery at least every 3 months to avoid damage.

Environmental statement

The chemical substances in the lithium-ion battery may pollute the environment. Have it removed by a professional before scrapping and hand it over to a professional battery recycling station for centralized disposal.

Steps to remove the battery

The following information is applicable only when discarding the mopping robot, not for daily operation:

1. Let the sweeping robot run until the power is low and cannot be cleaned without touching the station.
2. Shut down the sweeping robot.
3. Remove the battery cover at the bottom of the robot.
4. Press the buckle to pull out the connector plug of the battery and take out the battery.

Notice:

• When removing the battery, ensure it is fully charged and operating away from the station.
• Disassemble the entire battery pack together. Do not damage the battery pack casing to avoid short circuits or leakage of dangerous substances.
• If battery fluid comes into contact with skin, rinse with plenty of water and seek medical attention.
• Before discarding the appliance, remove the battery after the power is cut off and dispose of it safely.
• During charging, the battery must be placed in a well-ventilated area.

Accompany each radio equipment

A copy of the Declaration of Conformity (DoC) or a simplified declaration of conformity must accompany each radio equipment. The RED does not prohibit the display of the DoC or simplified DoC when it accompanies the radio equipment, in locations such as the operating manual, a separate sheet, or on the packaging.

Product Composition

List of accessories

Accessories installed on the robot:

• Robot
• Dustbin
• Filter (installed on the dustbin)
• Main brush
• Main brush cover

Accessories installed on the station:

• Self-sufficient station
• Sewage water tank
• Clean water tank
• Cleaning tray
• Dust bag

Other accessories:

• Mopping support*2
• Mop cloth*2
• Movable base
• Cleaning tool
• Power cord
• Side brush
• Cleaning solution
• User manual

Host introduction

Main Unit Components:

• AI visual recognition sensor
• Collision sensor
• Recharge button/Indicator light
• Power button
• LIDAR
• Top cover

Button Functions:

• Power button: Press and hold for 3s to turn on or off. Short press to start or pause cleaning/sweeping.
• Recharge button: Short press when running to enter pause state. Short press when paused to start recharge. Short press when recharging to stop recharging.
• Child lock button: Press and hold for 3s to turn on or off the child lock.

Robot indicator status description:

Robot anatomy

Top View:

• Cliff sensor
• Ultrasonic sensor
• Side brush
• Main brush
• Left/Right wheel
• Universal wheel
• Battery pack
• Main brush cover
• Rotating mop bracket (removable)

Bottom View:

• Charging shrapnel
• Rear recharge sensor
• Main engine water inlet
• Dust inlet

Dustbin

• Dustbin cover
• Dustbin release key
• Air inlet
• Dust inlet
• Filter

Note: The dustbin must be installed in all cleaning modes, otherwise the host will not start.

Self-sufficient station

• Sewage water tank
• Clean water tank
• Dustbin
• Cleaning bracket
• Sewage filter hole
• Hair blade
• Movable base

Note: Hair cutting blade (hidden inside when the function is not running, protruding when the function is running).

Station indicator status description:

Installation

Removal and installation

Remove the anti-collision strips on both sides of the host. Install the mop assembly to the buckle of the shown position, and hear a "click", indicating that the installation is in place.

[Diagram: Robot with bumper strips and mop assembly attached]

Place the station and install the movable base

Place the station against the wall. Before use, align the station mobile base to the position of the station. A "da" sound indicates that the installation is in place.

[Diagram: Self-sufficient station placement with dimensions: 0.36m clearance on sides, 1.97m clearance in front, 0.59m height, 0.82m clearance above]

Tip:

• Do not place items within 5cm of the station and 1.5m in front of it.
• Do not place the station in direct sunlight or block the signal transmission area, otherwise the robot may not return automatically.
• The clean water tank, sewage tank, and cleaning tray must be installed.

Power on and charge

When using for the first time, press and hold the power button for 3 seconds to turn it on. After turning it on, manually place the robot on the station, aligning the charging pole piece with the battery connector. In daily use, press the recharge button to start smart recharge.

[Diagram: Robot on charging station with power interface and power cord storage slot]

Tip:

• Wrap excess power cable around the storage slot. Secure the cable to the bottom slot to prevent the host from dragging it and causing the station to shift or power off.
• For the first charge, fully charge the battery to protect it.
• When the battery is low, place the robot on the station for charging.
• The robot automatically turns on after connecting to the station and cannot be turned off during charging.
• After the host is fully charged for 10 minutes, the host light turns off, and the station light turns on.
• For the first time, complete the quick drawing according to the APP prompts. Follow the host to clean up items that may affect its work.
• Ensure the host starts from the station and remove ground obstacles for accurate drawing.
• If areas may jam the host or scratch furniture, set a restricted area in the mobile APP.

APP Connection

1. Downloading the App

The robot can be controlled by the "ILIFEHOME" app. Scan the QR code to install the app on your iOS or Android device.

[QR Code for ILIFEHOME app on iOS]
[QR Code for ILIFEHOME app on Android]

2. Configure network

Press "U" + "<0xE4><0xBB><0x8B>" and hold for 3 seconds to configure the network.

[Diagram: Robot with buttons indicated for network configuration]

3. Add the machine on the APP interface and enter the Wi-Fi password to connect.

• Android phones are tied to Wi-Fi: Follow the mobile phone screen prompts.
• iOS phones are bound to Wi-Fi: Go to the mobile phone Wi-Fi Settings page, select the product's hot spot, and wait for a successful connection. Return to the APP interface, click next, and follow the prompts to complete the connection.

[Diagram: Mobile phone screen showing Wi-Fi connection settings]

Tip: Only Wi-Fi networks in the 2.4GHz band are supported.

How To Use

Install accessories according to desired cleaning mode

1. Sweeping mode

(Ensure the dustbin is installed on the host)

Open the face cover, put the dustbin into the main engine, and ensure the buckle is firmly stuck.

[Diagram: Robot with dustbin insertion and flap opening]

Tip: Clean the dustbin and filter regularly to maintain cleaning effectiveness.

2. Mop mode

(Installation of dustbin, mop assembly, cleaning tank, sewage tank)

1. Install the mop assembly to the buckle in the shown position. A "click" sound indicates it's installed correctly.
2. Fill the clean water tank to the maximum (MAX) water level.

[Diagram: Mop assembly installation and water tank filling]

Attention:

• Do not inject hot water into the clean water tank or sewage tank to avoid deformation.
• When mopping the floor, set up a virtual wall or restricted area in carpeted areas.
• In stagnant environments, clean up stagnant water before using sweeping or mopping functions.
• After mopping, remove and clean the sewage tank and cleaning tray promptly to avoid odor and mildew.
• New products may have slight water stains from factory testing, which is normal.

3. Install the cleaning solution on the station

1. Remove the front cover.
2. Place the cleaning liquid bottle horizontally and push it into the card slot.

[Diagram: Inserting cleaning solution bottle into the station]

Quick guide

1. Start the host

Press the host key "U" to start cleaning.

[Diagram: Robot with power button highlighted]

2. On/Off

Press and hold the "U" for 3 seconds to turn on. When not charging or suspended, press and hold the "U" for 3 seconds to shut down.

3. Pause

During cleaning or recharging, press any key to pause, then press "U" to continue working.

4. Sleep mode

In a non-charging state, if the host is idle for 10 minutes, it enters sleep mode. It shuts down after 6 hours of sleep. In sleep state, it can be woken up by pressing the button or via the APP.

Tip: The host will not go to sleep when it is on the station.

5. Recharge

When the battery is low during cleaning, it will automatically recharge. When the power is sufficient, it will return to the breakpoint to continue cleaning. In standby mode, press the "U" key to start recharge. During cleaning, press "U" to pause, then press "U" again to recharge. The robot determines whether to clean the mop based on the cleaning mode.

6. Child lock

To enable or disable the child lock function, hold down the "<0xE2><0x9A><0x96>" button on the host for 3 seconds to charge or pause.

Mode/gear selection

In the APP, choose from various cleaning modes and suction gears.

1. Memory map

After quick construction or cleaning is completed and recharge is successful, the host automatically saves and updates the map in the APP. Once the map is drawn, divide and merge areas or customize room names in the APP.

2. Wash mop

During sweeping, the host automatically returns to the station to clean the mop and continues sweeping. After mopping is completed, the host returns to the station to clean the mop, then starts to dry and charge. When the host is on standby, select the cleaning function in the APP to start mop cleaning, drying, and charging.

Tip: Check if the station is powered off, the cleaning water tank is empty, the host has left the station, the sewage tank is full, or the cleaning tray is not installed before cleaning.

3. Breakpoint continuation

This product supports breakpoint continuous scanning. When the power is low during cleaning, the host automatically seeks the station to charge and performs intelligent charging. After reaching the set power level, it returns to the breakpoint to continue cleaning. If cleaning, movement, or operation is manually ended during recharge or charging, the host cancels the breakpoint resuming.

4. Scheduled cleaning

Use the APP to set a scheduled cleaning time. The host automatically starts cleaning at the specified time and returns to the station when finished.

Tip: If "Do Not Disturb" mode is enabled, scheduled cleaning will not be performed during that period.

5. Dust collecting function

After the host completes the cleaning task and recharges, the station automatically collects dust.

Tip:

• The station will not automatically collect dust if the host returns to clean the mop halfway.
• If the automatic dust collection function is turned off in the APP, the station will not collect dust.
• If the dust collection frequency is modified in the APP, the station collects dust according to the set frequency.

6. Virtual wall/Restricted area

Use the APP to set up virtual walls or restricted areas to prohibit the host from entering areas that do not need cleaning.

Tip:

• Save the map in the APP before using this function.
• Moving the host or changing the home environment may cause the original map to fail, and the virtual wall/restricted area may be lost.

7. Global cleaning

If the map is not saved, select global cleaning for the host to clean a 6m x 6m area. After saving the map in the APP, select global cleaning for the host to plan a path to clean room by room and return to the station after cleaning.

8. Zone cleaning

Zone cleaning can be set in the APP, and the host cleans according to the planned area.

Tip: During cleaning, the host may go beyond the designated area. Clear ground obstacles around the designated area. Domain dashing does not serve as security isolation.

9. Do not disturb mode

In this mode, the host does not perform breakpoint continued scanning, scheduled cleaning, or active voice broadcasting. The indicator is off 10 seconds after the host returns to the station. This mode can be turned on or off in the APP.

Tip: For more functions, refer to the APP. Specific situations of each function are subject to the APP.

10. Reset Wi-Fi

Press "U" + "<0xE4><0xBB><0x8B>" and hold for 3 seconds to configure the network.

Tip: Only Wi-Fi networks in the 2.4GHz band are supported.

11. Reset/restore system

Press and hold the recharge button for 5S. After hearing the system reset successfully, the host automatically restarts, and settings like scheduled cleaning and Wi-Fi are restored to factory defaults.

Routine Maintenance

Cleaning tray

Take out the cleaning dish, rinse it fully, and clean dirt with a rag. Wipe the cleaning tray with a dry cloth and put it back.

[Diagram: Station assisted flushing]

Tip: Do not tilt the station during use and cleaning. If there is water on the cleaning tray or its bottom, dry it with a rag.

Sewage water tank

Tips:

• Clean the sewage tank promptly after the cleaning task is completed.
• The floats in the water tank and sewage tank are moving parts. Do not use excessive force during cleaning to avoid affecting functionality.

[Diagram: Sewage water tank removal and cleaning]

Replace dust bag

1. When a new dust bag is needed, open the dust collecting bin cover, pull the dust bag handle, remove the dust bag, and discard it.

Tip: Pulling the dust bag handle seals the bag and prevents dust from falling out.

2. Install the new dust bag according to the figure, insert the dust bag handle into the card slot, and install it in place.
3. Clip the top of the dust collecting bin cover first, then press the bottom until you hear a "click" sound, ensuring the dust collecting bin is completely closed.

[Diagram: Dust bag replacement steps]

Chip box

1. Hold the buttons on both sides of the movable base, press them, and pull out the movable base.
2. Remove the movable base and clean the chip box.
3. After cleaning the chip box of the movable base, align the active base with the connection point of the station fixed base and install it back. A "da" sound indicates it's installed correctly.

[Diagram: Chip box cleaning steps]

Dustbin and filters

1. Open the host cover, press the dustbin release button, and take out the dustbin.
2. Take out the filter, clean the dustbin and filter. If necessary, clean with water, dry, and put back.

[Diagram: Dustbin and filter removal and cleaning]

Tip: It is not recommended to wash the filter frequently. After washing, ensure it is completely dry before installing.

Main brush

1. Turn the machine over, grab the two main brush cover clips, and remove the main brush cover.
2. Take out the main brush, and unplug the main brush sleeve to clean dirt.
3. After cleaning, install the main brush shaft sleeve, main brush, and main brush cover. A "click" sound when installing the cover indicates it's in place.

[Diagram: Main brush removal and installation]

Side brush and universal wheel

1. Turn the main engine over and pull out the side brush and universal wheel upward.
2. Clean hair and dirt on the side brush and universal wheel.
3. Reinstall the edge brush and universal wheel. Align the side brush with the buckle when installing.

[Diagram: Side brush and universal wheel cleaning and reinstallation]

Tip: Clean the side brush and universal wheel every 2 weeks for optimal cleaning effect.

Sensor

Clean the sensors regularly with a soft, dry cloth.

[Diagram: Robot sensors (Cliff sensor, Ultrasonic sensor, AI visual recognition sensor, Collision sensor, LiDAR, Charging pole piece, Rear recharge sensor)]

Note: Do not use chemicals like detergents or sprays to clean the sensors.

Routine maintenance table

To keep the host in good condition, refer to the following table for routine maintenance:

Tip: Replacement frequency is for reference only. If parts are damaged, replace them promptly. If moving or mailing the product, empty the sewage tank and clean the water tank to avoid damage during transportation.

Product Specification

Main unit

Self-empty station

Common Problems

Troubleshooting