Associated RC8 B4.1 Setup Sheet
Event: Slough national | Track: RWMCC
Driver: William Paul | Date: 16-17/8/25 | Qualify: 1 | Main: 1/32a | Finish: 1 | Best Lap Time: 37
Front Suspension
Ride Height: 23mm
| Toe: 1 | Hex: 0 |
| Anti-Roll Bar Size: 2.2 | Gap: 2 |
Ackerman Plate: [Diagram showing a plate with markings 'TOP', '3', '2', '1']
Steering Arm Plate: [Diagram showing a steering arm assembly. Includes fields for Drive Shaft (CVAS [ ]), Universals [ ]) and shows a connection point for the steering linkage.]
Upper Arm Material: [ ]
Lower Arm Material: [ ]
Tower Material (F/R): Ali
Notes: [ ]
Caster Shim: 1mm
Insert: Carbon
Upper Ball Type & Shims: Kit
Steering Block KPI: 8: [ ] 16: [ ]
Washers: +2
Diagram: [Shows a front suspension upright assembly with steering block, ball joints, and drive shaft connection. Includes KPI adjustment points (8, 16) and washer count (+2).]
Lower Ball Type & Shims: Kit
Rear Suspension
Ride Height: 27mm
| Camber: 2 | Hex: 0 |
| Anti-Roll Bar Size: 2.3 | Gap: 0 |
Drive Shaft: CVAS [ ], Universals [ ]
Chassis Brace: [ ]
Pivot Type: Kit
Insert Type: Kit
Rear Arm/Hub Material: Kit
Notes: [ ]
Hub Tower: Std [x] High/Low: [ ]
Swaybar Ball Leverage: Wide [ ], Narrow: [ ]
Diagram: [Shows a rear suspension assembly including hub carrier, lower arm, and swaybar connection points. Features adjustable mounting points for the arm (Mount C, Mount D) with multiple hole positions.]
Hub Shim: 0
Diagram: [Shows a rear hub carrier assembly with labels 'CBA', 'FED'.]
Diagram: [Shows a rear hub carrier assembly with label 'CBA'.]
Wheelbase Shim: 0
Insert: None
Diagram: [Shows a wing mount assembly with numbered positions 5, 4, 3, 2, 1 and Wing Height options: High [ ], Low [ ].]
Electronics and Engine
| Radio: [ ] | Receiver: [ ] | |
| Throttle Servo: Speed: 0.05 | Steering Servo: Speed: 0.07 | |
| EPA: Throttle: 55 | Brake: [ ] | Steering: [ ] |
| EXPO: Throttle: -20 | Brake: -25 | Steering: [ ] |
| Brake Bias: 60/40 | D/R: 100% | |
| Receiver Battery: Reedy 2400 | ||
| Engine: Ad3 | Temp: [ ] | |
| Pipe: [ ] | Fuel: Speedwurx | |
| Restrictor: 6.5 | Glow Plug: P3 | |
| Chassis Layout: FWB [x] RWB [ ] |
Notes: [ ]
Differential
| Front | Center | Rear |
|---|---|---|
| Fluid: 15K | 15K | 10K |
| Gears: LTC | LTC | LTC |
| Mass: [ ] | [ ] | [ ] |
Notes: [ ]
Shocks
| Front | Rear |
|---|---|
| Piston: 6x1.3 | 6x1.3 |
| Fluid: 37.5 | 32.5 |
| Bladder: Honeycomb | Honeycomb |
| Rebound: Minimal | Minimal |
| Spring: Blue | Gray |
| Length: 104 | 124 |
| Eyelet: 0 | 0 |
Notes: [ ]
Diagram: [Shows a shock absorber, indicating its length and rebound adjustment mechanism.]
Clutch and Gearing
| Spur Gear: 47T | Bell: 13T |
| Shoes: 2 carbon, 2 ali | |
| Springs: 0.95, 1 |
Notes: [ ]
Track Info
| Size: Medium |
| Surface: Dusty dirt |
| Traction: High |
| Moisture: Dry |
| Condition: [ ] |
| Temperature: 26 |
Notes: [ ]
Tires
| Front Tires: Pro-line convicts |
| Front Compound: M3 |
| Front Insert: Proline |
| Rear Tires: Pro-line convicts |
| Rear Compound: M3 |
| Rear Insert: Proline |
| Wheel (F/R): Jc racing |
Notes: Glued front side wall
Body, Weight
| Body: Xtreme aria |
| Nose Cone: 3d printed |
| Rear Wing: Xtreme polycarbo |
| Wing Angle: 0° [ ] 2° [x] 4° [ ] |
| Wing Buttons: Flat [ ] Fin [x] |
| Vent Holes: [ ] |
| Total Weight: [ ] |
Notes: [ ]
Radio Tray Flex Assembly
| Transponder Mount: [ ] | None: [x] |
| Radio Tray Brace: [ ] |
Notes: [ ]
Vehicle Comments
Notes: [ ]
