Associated RC8B4.1 Setup Sheet
Driver: Neil Cragg | Event: 40+ Euros | Track: Herts (New Layout) | Date: 26/27/07/2025 | Qualify: 2nd | TQ: Main: A | Finish: 2nd
Front Suspension
Ride Height: | 25 | Caster Shim: | 4.2mm | Wheelbase Shim: | Split (1 front 1 rear) |
Toe: | +2 (Toe Out) | Hex: | 4mm (Kit) | Insert: | Yes |
Anti-Roll Bar Size: | NONE | Insert: | None | ||
Gap: | |||||
Ackerman | |||||
Steering Arm Plate: | +1 | Steering Block KPI: | 8: [selected], 16: [unselected] | ||
Drive Shaft: | CVAs: Universals: | Washers: | B, A | ||
Upper Arm Material: | Medium | ||||
Lower Arm Material: | Medium | ||||
Tower Material (F/R): | Aluminium | ||||
Notes: |
Diagrams:
Upper Ball Type & Shims: Alloy (1.4mm) - Depicts a ball stud with shims for adjustment.
Lower Ball Type & Shims: Steel (0.7mm) - Shows a lower ball stud with shims.
Tower/Arm Mount KPI: Shows adjustment holes for King Pin Inclination (KPI) at 8 and 16 degrees on the tower and arm mount, with 8° selected.
Steering Block KPI: Shows adjustment holes for King Pin Inclination (KPI) at 8 and 16 degrees on the steering block, with 8° selected.
Arm Mounts: Illustrations of Upper Arm, Mount, Arm Mount A, and Arm Mount B, showing connection points and adjustment options.
Rear Suspension
Ride Height: | 28 | Hub Tower: | Std [unselected], High/Low [selected] | Swaybar Ball Leverage: | Wide [selected], Narrow [unselected] |
Camber: | -2.5 | Hex: | 4mm (Kit) | ||
Anti-Roll Bar Size: | NONE | ||||
Gap: | |||||
Drive Shaft: | CVAs: Universals: | Hub Shim: | 2.0mm at Rear of hub | ||
Chassis Brace | |||||
Pivot Type: | Fixed | Wheelbase Shim: | At rear of arm | ||
Insert Type: | |||||
Rear Arm/Hub Material: | Medium | ||||
Notes: |
Diagrams:
Hub Tower: Illustrates selection between Standard, High, or Low hub tower positions.
Swaybar Ball Leverage: Shows options for Wide or Narrow swaybar ball connection points, with Wide selected.
Arm Mounts: Illustrations of Arm Mount C and Arm Mount D, showing connection points and adjustment options.
Wing Height: Depicts adjustment for High or Low wing mounting positions.
Electronics and Engine
Radio: | Sanwa | Receiver: | SMD | ||
Throttle Servo: | Sanwa PGS-XBII | Speed: | |||
Steering Servo: | Sanwa PGS-XBII | Speed: | |||
EPA: Throttle: | Brake: | Steering: | |||
EXPO: Throttle: | Brake: | Steering: | |||
Brake Bias: | 50/50 | D/R: | |||
Receiver Battery: | Reedy | ||||
Engine: | Alpha Falcon B Spec | Temp: | |||
Pipe: | Alpha 2159 | Fuel: | Pirhana 16% | ||
Restrictor: | 8.0mm | Glow Plug: | OS P3 | ||
Chassis Layout: | FWB | RWB | |||
Notes: |
Drivetrain
Differential
Front | Center | Rear | |
---|---|---|---|
Fluid: | 10k | 10k | 7k |
Gears: | 18 | 19 | 18 |
Mass: | |||
Notes: | 2 Gear (Front and Rear) |
Clutch and Gearing
Spur Gear: | 47T | Bell: | 13T | Eyelet: | 0 |
Shoes: | 4 x Aluminium | ||||
Springs: | 2 x hard, 2 x Medium | ||||
Notes: | (H position) |
Shocks
Front | Rear | |
---|---|---|
Piston: | 6 x 1.3mm (Flat) | 6 x 1.3mm (Tapered) |
Fluid: | 37.5wt | 32.5wt |
Bladder: | Fastrace | Fastrace |
Rebound: | Full | Full |
Spring: | AE Grey | AE Grey |
Length: | 96 | 120 |
Eyelet: | 0 | 0 |
Notes: |
Track Info
Size: | Large | ||||
Surface: | Dirt | ||||
Traction: | Medium | ||||
Moisture: | WET | ||||
Condition: | Oiled | ||||
Temperature: | 30C | ||||
Notes: |
Tires
Front Tires: | Jetko J-One (Handout) | Rear Tires: | Jetko J-One (Handout) | ||
Front Compound: | Jetko J-One (Handout) | Rear Compound: | Jetko J-One (Handout) | ||
Front Insert: | Jetko J-One (Handout) | Rear Insert: | Jetko J-One (Handout) | ||
Wheel (F/R): | Jetko (Handout) | ||||
Notes: |
Body, Weight
Body: | Xtreme Aria | Nose Cone: | Yes | ||
Rear Wing: | Xray | ||||
Wing Angle: | 0° [selected], 2°, 4° | ||||
Wing Buttons: | Flat [selected], Fin | ||||
Vent Holes: | 5 x 8mm | ||||
Total Weight: | |||||
Notes: |
Radio Tray Flex Assembly
Transponder Mount: | None: [selected] | ||||
Radio Tray Brace: | |||||
Vehicle Comments: | |||||
Notes: |