©Libro Corp. All Rights Reserved.
Manufacturer: Shenzhen Libro Technology Co., Ltd.
Address: Building 3, Cloud Park, Shenzhen, China, 518129
CAN ICES-3 (B)/NMB-3(B)
FCC ID: 2A3DE-PLAF103
Made in China
PLAF103_V1.0
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Read this manual before using the product, and keep it for future reference.
This product is intended for household use only.
Safety Guidelines
⚠️ WARNING
- Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation; keep away from children and pets.
- Do NOT allow small children to play with, in or around the pet feeder.
- To reduce the risk of injury, please keep close supervision when the appliance is used near children.
- Do NOT use the feeder with pets not able to reach the food tray or with any physical disability.
- Do NOT immerse the base part in water at any time as it may damage electronic components like the control panel.
- Do NOT place any foreign object in the pet feeder.
- Do NOT use outdoors. Check operation frequently to be sure the unit is dispensing properly.
- Do NOT use wet, canned or moist food.
- Do NOT disassemble the unit other than as instructed in this User Guide.
- Do NOT use the feeder for anything other than its intended use.
- Only use attachments recommended or sold by the manufacturer. The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition. Do not modify the pet feeder.
- Do not operate any appliance if the unit is malfunctioning or has been damaged. Do not attempt repairs on the pet feeder yourself. Contact customer service immediately for further instructions.
- Always unplug when not in use and before cleaning.
- Never pull on the electrical power cord to remove the plug from the wall outlet.
- If the plug of this device gets wet, turn off the electricity to that wall outlet. Do not attempt to unplug.
- Examine the feeder after installation. Do not plug in if there is water on the power cord or plug.
- To avoid tripping, always position power cord out of the way of foot traffic.
CAUTION
- Do NOT install or store the pet feeder where it will be exposed to weather or temperatures below 4°C / 39.2°F.
- Use alkaline D batteries to power. Do NOT use rechargeable batteries.
- Check the batteries regularly. Before leaving for extended time, always replace batteries with new ones.
- Do NOT lift the pet feeder by lid, food tank, or food tray. Lift and carry it using both hands and the base, while keeping the unit in an upright position.
- Suitable for dry food ONLY, with kibble size ranging from 2-15mm / 0.07-0.6 inch in diameter. Larger kibble may get stuck at the food outlet.
- Do not put your fingers into the food outlet or let your fingers touch the rotor.
- Read and observe all important notices listed on the pet feeder and in the packaging.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Radiation Exposure Statement: To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with minimum distance of 20cm from your body.
Warranty
- 1-year warranty
- Lifetime support
For guidance on product use and warranty extension, please contact the brand after-sales staff via email: support@petlibro.com.
If any questions related to orders, please contact the seller through the shopping platform.
In the Box
The PETLIBRO Granary Automatic Pet Feeder package includes:
- 1 Automatic Pet Feeder (main unit with food tank and base)
- 1 Double Food Bowls with Holder (two stainless steel bowls in a holder)
- 1 Meal Splitter (for dividing food between bowls)
- 1 User Guide Kit (this manual)
- 1 Power Adapter (for electrical connection)
- 1 Desiccant Bag (for moisture absorption)
Visual description: The main unit is a cylindrical feeder with a transparent window for food level. The double food bowls sit in a holder at the base. The meal splitter is a small blue component. The power adapter is a standard wall plug. The desiccant bag is a small pouch.
Product Overview
The PETLIBRO Granary Automatic Pet Feeder consists of the following main parts:
- Lid: Top cover of the food tank.
- Seal Strip: Gasket under the lid for airtight sealing.
- Food Tank: Main container for dry pet food.
- Transparent Window: Allows visibility of the food level inside the tank.
- Tank Base: Bottom part of the food tank assembly.
- Anti-Clog Detector: Sensor to prevent food blockages.
- Control Panel: Area with buttons and indicators.
- Display Panel: Screen for status information.
- Food Outlet: Where food dispenses from the tank.
- Feeder Base: Main base unit of the feeder.
- Stainless Steel Bowl: Individual food bowls.
- Bowl Holder: Tray that holds the two stainless steel bowls.
- Meal Splitter: Device to divide food into two bowls.
- Desiccant Box: Compartment for the desiccant bag, located under the lid.
- Power Jack: Port for connecting the power adapter.
- Power Adaptor: External power supply.
- Battery Compartment: Located at the bottom of the feeder for backup batteries.
- Compartment Lid: Cover for the battery compartment.
- Speaker: For audio feedback and recorded meal calls.
Visual description: A diagram shows an exploded view of the feeder, labeling each component from the lid down to the base and bowls. Separate diagrams show the desiccant box location, power jack, battery compartment, and speaker.
Set Up the Feeder
Assembly and Prepare for Setting
- Connect Power:
- Plug the 5V power adapter into a power socket and the USB cable into the USB port on the back of the feeder.
- The LED display will light up automatically to indicate the feeder is on.
- Open the battery compartment at the bottom of the feeder. Install three alkaline D batteries (not included) in case of a power outage. Ensure the batteries match the positive and negative poles with the markings in the compartment.
Notes:- Batteries are not included.
- To avoid sudden power outage and ensure pet feeding, do not use the batteries as the only power source. Batteries are for emergency use only.
- To avoid battery leakage, remove the batteries if the device will not be in use for a period of time.
Visual description: A diagram shows the feeder base with the battery compartment open, indicating where to insert three D batteries.
- Twist anticlockwise to open the lid.
Visual description: A diagram shows the lid being twisted counter-clockwise to unlock and remove it from the food tank.
- Place the desiccant bag into the inner box under the lid.
Notes:- It is recommended to change the desiccant bag every 15 days to prevent mold growth.
- Remove the desiccant bag before cleaning the lid.
Visual description: A diagram shows the desiccant bag being placed into a designated slot inside the lid.
- Add dry pet food to the food tank.
Notes:- To prevent uneven food dispensing, please add enough pet food to the visible level.
- Recommended kibble size: 2-15mm / 0.07-0.6 inch in diameter.
- Do not use canned, wet, or moist food.
Visual description: A diagram shows dry kibble being poured into the food tank, with a line indicating the minimum grain level.
- Put the lid back on.
To snap into place, turn the lid clockwise from the right rotating sign to the left rotating sign.
Visual description: A diagram shows the lid being placed back on the food tank and twisted clockwise to lock it into position.
- Take out and install the double food tray.
Attach the double food tray to the notch underneath the feeder base.
Visual description: A diagram shows the double food bowls with holder being slid into place underneath the feeder base.
- Install the meal splitter by aligning it with the round hole.
Visual description: A diagram shows the meal splitter being inserted into a round hole at the food outlet, then rotated to lock into place.
- To get an equal amount of food, move the splitter to the right until it can't move. (Visual: Splitter centered, food flowing equally into two bowls).
- To get an uneven amount of food, move the splitter to the left; more food will be dispensed to the right bowl. (Visual: Splitter shifted left, more food in the right bowl).
Note: To remove the bowl holder from the feeder base, move the meal splitter away from the food outlet.
If there is grain in the food bowl, handle it gently to avoid spilling. Hold the base instead of any other parts when lifting the feeder.
Visual description: Diagrams illustrate adjusting the meal splitter for equal or uneven food distribution. Another diagram shows how to remove the meal splitter by sliding it away from the food outlet, and how to lift the feeder by its base.
Controlling Via App
Note: The feeder supports 2.4GHz and 5GHz WiFi.
System Requirements
- iPhone on iOS 10.0 or later
- Smartphone on Android 5.0 or later
Install the APP & Log in
- Search "PETLIBRO LITE" in App Store (Google Play Store or Apple App Store) to download the App.
- Sign up and log into your account.
Add the Device
A. Add the Feeder Via Bluetooth Mode
- Open the App, select Home page, tap "Add Device" or "+" in the upper right corner.
- Choose "PLAF103 WiFi Feeder".
- Follow the instructions on the screen, and confirm the WiFi indicator on the feeder is flashing. (Note: If the WiFi indicator on the feeder is not flashing, hold the unlocked button for 5s to unlock, the lock indicator goes out. Keep holding the reset button until the WiFi indicator keeps flashing.)
- Add the device PLAF103 by entering your WiFi account and password.
- Feeder connected. Start to set the feeding time and portions, record meal call, and set the times the meal call plays.
Visual description: Screenshots of the PETLIBRO LITE app showing the "Add Device" screen, device selection (PLAF103 WiFi Feeder), and input fields for WiFi credentials. Also, images of the feeder's control panel showing the WiFi indicator flashing, lock indicator off, and reset button being held.
B. Add the Feeder in AP Mode
- Turn off Bluetooth on your phone.
- Open the App, tap "Add Device" or "+" in the upper right corner, choose PLAF103 WiFi Feeder, tap the icon at the top right corner and choose AP mode.
- Confirm the WiFi indicator on the feeder is flashing. (Note: If the WiFi indicator on the feeder is not flashing, hold the unlocked button for 5s to unlock, the lock indicator goes out. Keep holding the reset button until the WiFi indicator keeps flashing.)
- Enter your WiFi account and password, and go to the WiFi connection interface on your phone, find the device "SL-PETLIBRO-xxxx" and tap to connect.
- Back to the App and wait for connecting.
- Feeder connected. Start to set the meal time and portion size, record meal call, and set the times the meal call plays.
Visual description: Screenshots of the PETLIBRO LITE app showing Bluetooth being off, selecting AP mode, and the WiFi connection process.
Set Meal Plan
On the Schedule page, tap the Add icon, choose feeding time, feeding days, and feeding portions.
Visual description: Screenshots of the app's schedule page, showing options to add new feeding times, select days of the week, and set portion sizes.
Manually Feeding the Pet
On the Manual page, choose the portion you want to feed first, then tap the Feed icon. The feeder will feed immediately.
Visual description: Screenshot of the app's manual feeding page, showing options to select portion size and a "FEED" button.
View the Logs
On the Log page, you can view feeding records and abnormal notifications.
Visual description: Screenshot of the app's log page, displaying a list of feeding events (success/fail), low food warnings, outlet blockages, and low battery notifications.
Record a Meal Call & Set Playback Times
Tap the ? icon in the top right corner → Recording, then tap the Add icon, follow the instructions on the screen to record a meal call, set the times the meal call plays.
Note: The device can only keep the latest recording. When a new recording is done, the old recording will be automatically deleted.
Visual description: Screenshots of the app's recording settings, showing options to record a new meal call and set playback times.
Reset the Feeder on App
Tap the ⚙️ icon in the top right corner → Factory Reset. The feeder emits beeps: Di, DiDi, and the WiFi indicator keeps flashing, indicating the device is ready for re-connection.
Share the Device
Tap the ⚙️ icon in the top right corner → Share Device → Add Sharing.
If you want to add the feeder to another person's mobile phone, register a new account on his/her phone first, then you can share the device with the new account. Make sure the two accounts are registered in the same country.
Remove Device
Tap the ⚙️ icon in the top right corner → Remove Device → Disconnect.
Check FAQs and Send Feedback
Tap the ⚙️ icon in the top right corner → FAQ&Feedback.
Check the frequently asked questions related to the device, and you can also submit questions and feedback.
Clean and Care
It is recommended to clean the feeder regularly for the health of pets.
The washable parts are as follows: lid, food tank, tank base, stainless steel bowl, and bowl holder.
Clean other parts with a dry cloth.
Clean the tank lid, food tank, tank base
Before removing the food tank, be sure the food tank is empty in case of food spilling all over.
- Disconnect power before cleaning.
Visual description: A power plug being disconnected from an outlet.
- Twist anticlockwise to remove the lid and take out the desiccant bag from the inner box under the lid.
Visual description: The lid being twisted counter-clockwise and lifted, then the desiccant bag being removed from its slot.
- Pull up along the notches to remove the tank.
Visual description: The food tank being lifted vertically from the feeder base by pulling on designated notches.
- Twist anticlockwise to remove the tank base.
Visual description: The tank base being twisted counter-clockwise to detach it from the main feeder body.
- Thoroughly rinse and air dry the lid, tank and tank base.
Visual description: Icons representing rinsing with water (?) and air drying (☀️) the disassembled lid, tank, and tank base.
- Refit them to the machine. Turn the tank base clockwise until it snaps into place.
Visual description: The tank base being reattached and twisted clockwise until it locks.
- Then install the tank and lid.
Visual description: The food tank being placed back onto the base, followed by the lid being placed and twisted to lock.
Clean the Bowls and Holder
- Remove the bowl holder from the feeder base.
Visual description: The double food bowls with holder being slid out from underneath the feeder base.
- Rinse the stainless steel bowls and holder, and air dry them thoroughly before refitting them to the machine.
Visual description: Icons representing rinsing with water (?) and air drying (☀️) the stainless steel bowls and holder.
Specifications
| Model | PLAF103 |
|---|
| Capacity | 5 liters |
| Power | DC 5V power adapter; 3 x alkaline D batteries (not included) |
| Power Adapter | AC100-240V, 50/60Hz Input, DC 5V output |
| Operating Temperature | 0 - 55 ℃ / 32℉ - 131℉ |
| Dimensions | 34 x 19 x 19 cm / 13 x 7.5 x 7.5 in |
| Net Weight | 1.91kg / 4.21lbs |
Troubleshooting
The answers to these questions should help you solve most problems you may have with the pet feeder. If they do not, please contact the Customer Care Center via support@petlibro.com.
| Problem | Solution |
|---|
| I press the buttons but they don't work. | Press and hold the Unlocked Button for 5s to unlock the buttons. |
| The food won't come out. | - Please make sure the food in the tank is dry, and food size is within 2-15 mm / 0.07-0.6 inch in diameter.
- Remove the food tank and tank base, check if the chute inside is blocked.
- Check if the anti-clog detector at the food outlet is dirty or blocked.
- Check whether the battery level is low, whether the power adapter is connected, whether power outage occurs when the power adapter is connected and batteries are not installed.
|
| The indicators are off. | - Check whether the electricity is cut off.
- Check whether the indicator function is off on the App.
|
| I can't remove the food tank. | Please pull upwards along the notches on either side to remove the food tank. |
| The portion amount is not the same. | The first few portions may vary, but it doesn't mean the appliance is faulty. After about 6 feedings, it should be almost even. |
