WYBOT Robotic Pool Cleaner User Manual
Model: WYBOT A1(OS2010)
Read through the entire manual before running your new robotic pool cleaner, and keep this manual handy for your reference.
Introduction
Thank you for choosing WYBOT products. WYBOT Robotic Pool Cleaner is dedicated to providing high efficiency, low power consumption, easy operation, and thorough pool cleaning.
Its features include one-button activation, powerful suction and scrubbing, fine filtration, smart navigation, remote control, and high compatibility with various pool shapes and construction materials, assuring a convenient, intelligent, and optimal pool cleaning experience.
For any questions, feel free to contact WYBOTICS Co., Ltd. via email or visit their website.
Warning
Failure to operate the device as per the warnings can result in serious injury, electrocution, or death.
- Use only accessories recommended or sold by WYBOTICS Co., Ltd.
- Dry the charging port after each cleaning to prevent electric shock.
- Do not charge the cleaner when it is on.
- Use only the original and authorized power charger.
- Ensure the electrical outlet is protected by a GFCI and ELI.
- Do not use a damaged charger.
- Do not use an extension cord to connect the charger.
- Never allow children to ride on or play with the cleaner.
- Do not allow children to operate or maintain the device.
- Do not enter the pool when the cleaner is working.
- Never expose or charge the device in flammable environments.
- Only licensed professionals can disassemble sealed parts.
- Do not operate the cleaner while the pool filter is running.
Caution
Failure to operate the device as per the cautions can cause damage to the device or personal injury.
- Charge the unit before first use.
- Avoid putting fingers between movable parts, as the flipper hinge may move suddenly and cause injury.
- Disassemble the flipper if the device will not be used for a long time to prevent improper storage from snapping the flipper.
- Do not overcharge the cleaner to maintain battery life.
- Charge the cleaner before storing it for a long time (over 6 months) to maintain optimal battery life.
- Wash and clean the filter trays after each use.
- Store the cleaner in a cool, ventilated place, away from direct sunshine or heat sources.
- Use the pool cleaner in the following water conditions:
- Chlorine: Max. 4 mg/L
- pH: 7.0 - 7.8
- Temperature: 41-95 °F (5-35 °C)
- Salinity: Maximum 5000 PPM
WYBOT A1(OS2010) At a Glance
Product External Overview
a Handle: Remove and transport the device.
b On/Off Button: Turn the device on/off.
c Charging Port: Connect the charger.
d Flipper: Inserted into the device to help movement.
e LED Indicator: Shows device status and battery level with different colors.
f Outlet: Lets out water.
g Adjustable Wheel: Adjust to modify cleaning pattern.
h Assembly fastener: Locks and unlocks the top cover.
Product Internal Overview
i Sealed Part: Contains important components; do not disassemble without authorization.
K Filter Tray (Cotton foam): Recommended for daily pool maintenance. Avoid use when the pool is very dusty.
l Filter Tray (180µm): Traps the finest dirt, can be used independently or with the cotton foam filter.
m Storage cavity: Stores collected debris.
Note: Do not operate the device if the top cover or scrubbing brushes are broken. Stop charging or running if there is liquid leakage from the sealing part.
Packing List
- Device x 1
- Flipper x 1
- Filter tray (Cotton foam + 180µm) x 1
- Hook x 1
- User Manual x 1
- Quick Start Guide x 1
- Charger x 1
- Screw x 1
Get Started
Insert Flipper
Insert the flipper into the cleaner, aligning the notch and groove.
[Image: Diagram showing how to insert the flipper into the robotic pool cleaner.]
Charge Your New WYBOT A1(OS2010)
The device has a rechargeable lithium-ion battery. Charge it before first use and when the battery is low. Connect the device to a power outlet using the included cable and adapter.
Note:
- When charging, ensure the device is at least 3m (approx. 10ft) away from the pool edge.
- Keep the device and adapter away from direct sunshine or water when charging to reduce fire risk.
- For safety, double-check that the device is powered off and the charging port is dry before charging.
- The optimal charging environment is 32°F - 95°F (0°C - 35°C) with 5%-95% RH.
The cleaner indicates battery level with LED lights on the front:
| Quantity of Green Lights | Battery Level (%) |
|---|---|
| ●●●● | 75-100 (Fully Charged!) |
| ●●● | 50-75 |
| ●● | 25-50 |
| ● | 0-25 |
[Image: Diagram showing the robotic pool cleaner with LED indicators for battery level.]
Setup Your New WYBOT A1(OS2010)
Turn on the device by pressing and holding the on/off button for 1 second. The LED indicator will display a solid blue ? when the device is on and show the current battery level with a flashing green ? for 3 seconds.
[Image: Diagram showing the on/off button and LED indicator on the robotic pool cleaner.]
LED Indicator Status
| LED Light | Indication | Status |
|---|---|---|
| Blue (Solid) | Solid | Power On |
| Blue (Flashing) | Flashing | Under working |
| Purple (Solid) | Solid | Eco cleaning |
| Yellow (Flashing) | Flashing | Low battery or self-parking in the pool |
| Green (Solid) | Solid | Battery level |
| Red (Solid or flashing) | Solid or flashing | Fault |
Note:
- If the yellow light flashes, remove the device from water and charge it.
- If the red LED light is on, refer to the troubleshooting section or call for service.
Preset the Eco Cleaning Time
To optimize runtime, you can choose various cleaning times by pressing the on/off button.
Note:
- The eco cleaning time is based on a full battery charge.
- The default cleaning cycle is 120 minutes.
[Image: Diagram showing how to press the on/off button to preset eco cleaning time.]
When the LED light turns purple ?, you can preset the cleaning time. The runtime options are:
| Light Position | Eco Runtime | Remark |
|---|---|---|
| [Diagram showing light position 1] | 120min. | Default |
| [Diagram showing light position 2] | 60min. | Remove robot from pool within 10 min of completing preset eco time. Otherwise, it will restart in about 10 min and continue working until low battery. |
| [Diagram showing light position 3] | 40min. | Remove robot from pool within 10 min of completing preset eco time. Otherwise, it will restart in about 10 min and continue working until low battery. |
| [Diagram showing light position 4] | 30min. | Remove robot from pool within 10 min of completing preset eco time. Otherwise, it will restart in about 10 min and continue working until low battery. |
Run Your New WYBOT A1(OS2010)
- Preset a runtime for your robot.
- Hold the handle of the cleaner and put it into the pool vertically.
- Let it sink to the floor to empty trapped air inside.
- Allow 20 seconds for auto-calibration on the floor.
- The cleaner begins to clean the floor.
- The device will automatically move to stop by the edge of the wall when finishing cleaning or when the battery is low.
- You should insert the included hook into a pool rod and lift the cleaner out of the pool.
- You should take the cleaner out vertically to drain inside water quickly.
[Image: Sequence of diagrams illustrating the operation of the robotic pool cleaner in the pool.]
Do a Filter Cleaning
Take off the top cover by unlocking the fasteners on both sides.
[Image: Diagram showing how to unlock the fasteners to remove the top cover.]
Note:
- Ensure the device is powered off when opening the top cover.
- Clean the filter trays before they are dry.
Take out the filter trays.
[Image: Diagram showing the removal of filter trays.]
Shake off all debris, and rinse the filter tray with hose water. Hand wash the cotton foam.
[Image: Diagram showing cleaning of filter trays and cotton foam.]
After rinsing, put the filter basket back into the cleaner and close the cover.
[Image: Diagram showing reassembly of the filter basket and cover.]
Device Specification
| Name | Specification |
|---|---|
| Pool Size | 80m²~100m² (floor cleaning) |
| Water Depth | Max. 8.2ft (2.7m) & Min. 1.98ft (60cm) |
| Device Dimension | 13.6(L)*12.4(W)*6.7(H) inches / 345(L)*315(W)*170(H) mm |
| Weight | 3.5kg |
| Runtime | 2 hours |
| Charging Time | 2.5 hours |
| Voltage | 22.2V |
| Power | 33W |
| Charger Input | 100-240V, 50-60Hz |
| Charger Output | 25.2V/1A |
| Battery Capacity | 2600mAh |
| Filter | Double-level filtration |
| Flow Rate | 8.1 m³/H |
| Moving Speed | 16m/min |
| Water Resistance | IPX8 |
How to Maintain Your Device
Follow these steps to maintain good performance:
- Ensure the device is powered off.
- Dry out the cleaner and filter basket.
- Fully charge the battery.
- Store the cleaner in a cool, ventilated place, away from direct sunshine, heat source, frost, and squeezing, with an ambient temperature between 5°C/ 41°F and 45°C / 113°F.
- Charge the cleaner every three months to ensure optimal battery life.
Note: If the device does not work after a long-term low battery life or being off, contact the after-sale team. Do not attempt to disassemble it without authorization.
How to Adjust Your Cleaning Pattern
If your pool shape is irregular or you are not satisfied with the default cleaning pattern, you can change the direction of the adjustable wheels for better cleaning.
Detach the Adjustable Wheels
Locate the two wheel kits marked A, B, C, and D on the front and rear sides of the chassis. On the wheel stem, find the catch. Hold the catch and push it inwards to remove the wheel kit.
[Image: Diagram showing how to detach the adjustable wheels.]
Reset Combination Path
Insert the limiting lever on the wheel kit into holes marked A/B/C/D to modify your cleaning path.
[Image: Diagram showing the wheel stem and limiting lever.]
Below are the combination ways and their usage scenarios for the adjustable wheels:
| Combination | Use Scenario |
|---|---|
| A – C | Default (suitable to most pools) |
| A – B | Smaller rebounding angle compared with “A – C” |
| B – C | For round shape pools |
Example: Combination B-A
[Image: Diagram illustrating combination B-A for adjustable wheels.]
FAQ & Trouble Shooting
Q: Could this cleaner do wall and waterline cleaning?
A: This cleaner is designed for floor cleaning only. It does not support wall or waterline cleaning.
Q: Will obstacles such as steps, shallow water areas, drains, or slopes affect the running?
A: The machine prefers to run on a flat floor. High obstacles may cause the device to get stuck.
If you encounter the following situations, check the table below for solutions:
| Symptom | Possible Reason | Solution |
|---|---|---|
| Buzzer silent or impeller not rotating after power on | Low battery | Recharge the battery |
| Device fault | Contact after-sales service | |
| The buzzer still alarms or the impeller does not rotate after the cleaner is fully immersed in the water. | The flipper is stuck | Remove the cleaner from the pool and try to manually rotate the flipper or contact after-sales service. |
| The flipper cannot stand when the cleaner touches the wall | The flipper is stuck; try to clear the movable cavity. | |
| The swing plate can stand when the cleaner touches the wall, but the cleaner cannot reverse | The water channel is stuck | Try to clear foreign stuff. |
| Charger indicator does not work | The charger is damaged | Contact after-sales service. |
| The cleaner does not have a full coverage for the floor | Improper wheel angle | Adjust wheels position. |
| Special pool shape | Adjust wheels position. | |
| Swimming pool water circulation system is on | Shut down the system. |
Note: If you cannot find a solution in the table, please contact the after-sale team.
Limited Warranty
- All WYBOT pool cleaners are inspected and licensed according to local laws.
- The warranty duration for the battery, motor, and PCB is one (1) year from the purchasing date. Consumable parts, including filter basket, brush, and wheels, are not covered by warranty.
- The warranty applies only to original buyers and is not transferable.
- Damages caused by improper use, unauthorized repair, or disassembly are not covered by WYBOTICS Co., Ltd.'s warranty.
- The order number or record must be presented for any claim or repair within the warranty period.
Certification
WYBOT robotic pool cleaners have passed all performance and reliability tests and obtained relevant certifications. You can rest assured.
[Logos: CE, FC, ROHS, cULus Listed (Intertek)]
WYBOT Customer Care
Due to continuous product improvement, products in the manual are subject to change. WYBOTICS Co., Ltd. reserves the right to update products.
If you encounter any problems during use, please contact the after-sale team. For more details, visit the WYBOTICS website: www.wybotpool.com
Wybot Customer Service:
- Email: support@wybotpool.com
- Facebook: @WybotPool
- Tel: 1-866-777-6655
Document No. A2024201004
