Westfalia Tow Bar Installation Guide
For Škoda Rapid, Škoda Rapid Spaceback, Škoda Rapid Spaceback Monte Carlo, and Seat Toledo
Product Information
Brand: Westfalia Automotive
Part Number: 317 129 600 001
Compatible Vehicles:
- Škoda Rapid (from 11/2012)
- Škoda Rapid Spaceback (from 11/2013)
- Škoda Rapid Spaceback Monte Carlo (from 2015)
- Seat Toledo (from 03/2013)
Technical Specifications
Type: 317 129
Approval Number: E13 55R-01 3814
Class: A50-X
D-Value: 8.5 kN
Max. Vertical Load (S): 50 kg
Towable Mass: Refer to vehicle registration document
Important Safety and Installation Notes
Note: Adherence to national regulations for installation approval is mandatory. Modifications or alterations to the tow bar are prohibited and will void the operating license. Remove insulating material or underbody protection from the vehicle's contact surfaces for the tow bar. The tow bar is designed for towing trailers and carrying loads; other uses are prohibited. For vehicles with parking assistance systems, ensure the tow bar does not interfere with sensors. Adjustments or deactivation may be necessary if the ball mount is in the sensor's detection range. The tow bar is a safety component and must only be installed by qualified companies. Incorrect installation can lead to serious accidents. The German text of the instructions is binding.
Installation Guide
Step 1: Bumper Preparation
Remove the rear bumper sections. The diagram shows arrows indicating removal of side panels and a central section, with a cylindrical object being removed from the vehicle's underside.
Diagram showing bumper removal and access to mounting points.Step 2: Mount Brackets
Attach mounting brackets to the vehicle's chassis. The diagram shows brackets being secured with bolts labeled "a" (3x per side) to designated points on the chassis.
Illustration of attaching mounting brackets to the vehicle frame.Step 3: Chassis Attachment Points
Diagram illustrates the underside of the vehicle, highlighting the specific points where the mounting brackets are to be attached.
Detail of vehicle chassis attachment locations for tow bar brackets.Step 4: Install Tow Bar
Align and attach the main tow bar assembly (labeled '1') to the previously mounted brackets on the vehicle chassis.
Diagram showing the main tow bar being fitted onto the chassis brackets.Step 5: Secure Tow Bar
Position mounting plates and secure them using bolts (10.5x30x3 and M10x35). A torque specification of 95 Nm is required for M10x35 bolts.
Illustration of securing the tow bar with bolts and specifying torque.Step 6.1: Bumper Modification (Škoda Rapid, Seat Toledo)
Instructions for modifying or re-fitting the rear bumper for Škoda Rapid and Seat Toledo models. Diagrams indicate measurements (Y0, 30, 35) on the bumper, suggesting necessary adjustments for clearance or fitment. A tool is shown.
Diagrams showing bumper measurements and potential modifications.Step 6.2: Bumper Modification (Škoda Rapid Spaceback Monte Carlo)
Similar to Step 6.1, this section details bumper adjustments for the Škoda Rapid Spaceback Monte Carlo, with indicated measurements (Y0, 30, 35).
Diagrams showing bumper measurements and potential modifications for specific models.Step 7: Spare Tire Access
Illustration showing the vehicle's trunk area with the spare tire being removed or stowed, indicating considerations for access or storage after tow bar installation.
Illustration related to spare tire management during installation.Step 8.1: Tow Ball Assembly (Škoda Rapid, Seat Toledo)
Details the attachment of the tow ball assembly (labeled '2' and '3') to the tow bar receiver (labeled '1'). Uses bolts (M12, 13x24x2.5, M12x80). A torque specification of 95 Nm is required for M12x80 bolts.
Diagram showing the tow ball attachment process with hardware and torque specifications.Step 8.2: Tow Ball Assembly (Škoda Rapid Spaceback Monte Carlo)
Details the attachment of the tow ball assembly for the Monte Carlo variant, using similar hardware and torque specifications as Step 8.1.
Diagram showing the tow ball attachment process for specific models.Technical Compliance and Dimensions
ECE-R 55 Clearance Requirements:
Clearance must be provided according to Appendix 7, Figures 25a and 25b of the ECE-R 55 directive. Diagrams illustrate minimum clearance requirements, such as ensuring a gap greater than 49mm.
Diagrams illustrating required clearance zones around tow bar attachment points, with dimensions and compliance with ECE-R 55 regulations.Vehicle Weight Information:
Information pertains to permissible gross vehicle weight, towing capacity, and combined weights.
Diagrams showing vehicle weight limits and towing capacities.Declaration of Correct Installation
This section includes a declaration from Westfalia-Automotive GmbH confirming that the tow bar has been installed correctly according to manufacturer specifications and attachment points. It includes fields for vehicle details, license plate, and a space for the company's stamp and signature. It also confirms that the user has been informed about the product's use and maintenance.
