Victrola Brighton VTA-71 Instruction Manual

Safety Instructions

CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN

AVERTISSEMENT: RISQUE DE CHOC ÉLECTRIQUE – NE PAS OUVRIR.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

Warning: To reduce the risk of electric shock, do not remove the cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

CAUTION: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

WARNING: To prevent electric shock, do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

General Safety Points:

1. Read all safety and operating instructions before use.
2. Keep these instructions for future reference.
3. Heed all warnings on the appliance and in the operating instructions.
4. Follow all operating and use instructions.
5. Do not use this apparatus near water or moisture (e.g., in a wet basement or near a swimming pool).
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install according to manufacturer's instructions.
8. Do not install near heat sources (radiators, stoves, amplifiers, etc.).
9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades, one wider than the other. A grounding plug has two blades and a third grounding prong for safety. If the plug does not fit your outlet, consult an electrician.
10. Protect the power cord from being walked on or pinched, especially at the plugs and where it exits the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with manufacturer-specified carts, stands, tripods, brackets, or tables. Exercise caution when moving combinations to avoid tip-over.
13. Unplug during lightning storms or when unused for long periods.
14. Refer all servicing to qualified personnel. Servicing is required if the apparatus is damaged (e.g., power cord, liquid spill, dropped, not operating normally).
15. The mains plug is the disconnect device and shall remain readily operable.
16. Do not expose the apparatus to rain or moisture. Do not place liquid-filled objects (like vases) on the apparatus.
17. Use the equipment in a moderate climate.

Accessories Included

• Instruction Manual
• Warranty (Back of Manual)
• Power Adaptor

Product Overview

Front View

Diagram showing the top panel of the Victrola Brighton VTA-71 turntable.

• 1. POWER: Press to turn the unit ON or OFF.
• 2. BT OUT: Press to activate the Bluetooth output function.
• 3. PLAY/PAUSE (▶/❚❚): Press to start playback, press again to pause. Long press for 3 seconds to disconnect Bluetooth pairing (works only in Bluetooth mode).
• 4. PREVIOUS (<<): Skip to the previous track or station.
• 5. NEXT (>>): Skip to the next track or station.
• 6. Display Screen: Shows status information.
• 7. 3.5mm EARPHONE JACK: Accepts headphone/earphone plugs.
• 8. BT/PHONO/FM KNOB: Turn to select BT, PHONO, or FM mode.
• 9. VOLUME KNOB: Turn to adjust volume.

Rear View

Diagram showing the rear panel of the Victrola Brighton VTA-71 turntable.

• 10. LINE OUT jacks: RCA auxiliary output sockets (white and red) for connecting to an amplifier device. Connect the white plug to the white jack and the red plug to the red jack.
• 11. DC Input Jack: Connect the power adapter here to power the unit.

Part of the Turntable

Diagram showing key components of the turntable mechanism.

• 12. Turntable: The rotating platter where the record is placed.
• 13. 45 RPM adapter: Used for playing 45 RPM records.
• 14. Tone Arm holder: Secures the tone arm when not in use.
• 15. Cue Lever: Lifts and lowers the tone arm. Push the holder to the right to release the tone arm.
• 16. AUTO STOP ON/OFF SWITCH: When "ON", the turntable stops automatically after playback. When "OFF", it continues to spin.
• 17. Speed Selector: Choose between 33-1/3, 45, or 78 RPM.
• 18. Tone Arm: Holds the stylus and tracks the record groove.
• 19. STYLUS: The needle that reads the record groove.

Setup/Basic Operation

Setup

1. Remove the white protective needle cover by gently pulling towards the front of the unit.
2. Remove any packaging materials from the unit.
3. Connect the power adapter to the DC Input jack to power on the unit.

Note: It is strongly recommended that this product be operated only from the type of power source indicated on the marking label.

Basic Operation

1. Press the POWER button to turn the unit on.
2. Select the desired mode (BT, PHONO, or FM) by turning the BT/PHONO/FM KNOB.
3. Rotate the VOLUME KNOB to adjust the sound level.

Listening through RCA LINE OUT

For listening via an amplifier, first reduce the volume to minimum. Connect the white and red RCA plugs from your amplifier to the unit's LINE OUT jacks, ensuring correct color-to-jack matching (white to white, red to red).

Listening through Earphones/Headphones (not included)

For private listening, first reduce the volume to minimum. Insert your headphones' plug into the 3.5mm EARPHONE JACK, then adjust the volume using the VOLUME KNOB.

Note: The unit's speakers will automatically deactivate when headphones are plugged in.

Condensation Warning

When the unit is moved from a cold to a warm place, or experiences a sudden temperature change, condensation may form, preventing proper operation. In such cases, leave the unit plugged in for 1-2 hours after connecting it to an AC outlet to allow it to stabilize to the ambient temperature.

Vinyl Record Operation

1. Turn the unit ON by pressing the POWER button.
2. Turn the BT/PHONO/FM KNOB to select PHONO mode.
3. Gently open the dust cover.
4. Place the record on the turntable and select the correct speed (33-1/3, 45, or 78 RPM). Use the included 45 RPM adapter for 45 RPM records.
5. Gently push the Tone Arm holder to the right to release the TONE ARM.
6. Raise the Cue Lever to lift the TONE ARM off its support.
7. Move the TONE ARM gently to the edge of the record or the starting point of the track. The turntable will begin to turn.
8. Gently lower the TONE ARM by slowly releasing the CUE LEVER. The tone arm can also be lowered manually if the cue lever is not raised.
9. Turn the VOLUME KNOB to adjust the volume.
10. When playback is finished, slightly lift the tone arm using the CUE LEVER and return it to the TONE ARM holder.

Bluetooth Operation

An external device with Bluetooth connectivity can be wirelessly connected to this turntable using the Bluetooth Function.

Getting Connected Using Bluetooth

1. Turn the BT/PHONO/FM KNOB to select BT mode. The "bt" indicator will flash on the Display Screen.
2. Turn ON the Bluetooth setting on your external device. Wait a moment and look for the Bluetooth pairing name "Victrola Brighton".

NOTE: The effective distance between your external device and this unit is 10 meters (33ft).

3. Select the "Victrola Brighton" pairing name to connect the unit. Once connected, the "bt" indicator on the Display Screen will stop flashing.
4. Select music media files on your external device, then press the PLAY/PAUSE button (▶) to begin playback.
5. To temporarily pause playback, press the PLAY/PAUSE button (❚❚). Press again to resume.
6. To skip to the previous or next tracks, press the PREVIOUS (<<) or NEXT (>>) buttons.

Bluetooth-Out Operation

The product supports Bluetooth wireless connection (BT-OUT), allowing connection to external Bluetooth-compatible headphones or speakers (not included).

1. When playing a vinyl record, press the BT OUT button.
2. The "❈" icon flashes on the Display Screen.
3. Turn ON your external Bluetooth receiver device (e.g., Bluetooth headphones, speakers) and set it to pairing mode.
4. Wait a few seconds for the devices to connect automatically.
5. The "❈" icon stops flashing once pairing is successful.
6. Control playback from your BT speaker. (Volume can only be adjusted from your external Bluetooth Device.)

• Place the Bluetooth device within 1 meter (3.3 feet) of the product for correct pairing.
• The product stays in pairing mode for approximately 30 seconds. If pairing fails, repeat the steps after turning all devices OFF.
• "BT OUT" is only compatible with vinyl record playback.

Maintenance/Proper Handling

Handling Vinyl Records

• Do not touch the record's grooves. Handle records by the edges or label with clean hands to prevent damage and preserve quality.
• To clean a record, use a soft anti-static cloth to gently wipe the surface.
• Keep records in their protective sleeves when not in use.
• Always store records upright on their edges.
• Avoid storing records in direct sunlight, near heat sources (radiators, stoves), or in locations subject to vibration, excessive dust, heat, cold, or moisture.

How to Replace the Turntable Stylus (Replacement Stylus # VND-08)

Removing the Stylus from the Cartridge

Diagram 1: Shows holding point "A" and pushing point "B" on the stylus assembly.

1. Using your fingers, hold at point "A" and push down point "B".

WARNING: Applying too much force may damage or break the stylus.

Diagram 2: Shows the stylus separating from the front of the cartridge.

2. Continue to push down until the stylus separates from the front of the cartridge.

Diagram 3: Shows carefully removing the rear of the stylus from the cartridge.

3. Remove the rear of the stylus carefully from the cartridge.

Installing the Stylus

1. Follow the previous steps but in reverse.

Caution:

• Do not remove or bend the stylus needle.
• Do not touch the needle to avoid injury to your hand.
• Turn off the unit's power before replacing the stylus.
• Keep out of reach of children.

Please note: The stylus should last about 50 hours under normal use. It is recommended that the stylus be replaced as soon as you notice a change in sound quality.

Troubleshooting Guide

Please note: As a result of continual improvements, the design and specifications of this product are subject to change without notice.

Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.

Specifications

General

• Power adapter: DC 5V/1A
• Power Consumption: 5W
• Power Output: 2 × 2W
• Size: 12.7" (322mm) W × 12.3" (312mm) D × 5.2" (131mm) H
• Weight: 4.5 lbs (2kg)

Record Player

• Speeds: 33-1/3 RPM, 45 RPM, and 78 RPM

Bluetooth

• Bluetooth Version: V4.0
• Bluetooth Profiles: A2DP, AVRCP
• Bluetooth Frequency range: 2.402GHz-2.480GHz
• Operating Distance: 10 meters (33 ft.)

FCC Statement and Warnings

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   1. This device may not cause harmful interference, and
   2. This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CALIFORNIA PROP 65 WARNING

WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

IC WARNING

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Warranty

Victrola is a registered trademark of Innovative Technology Electronics LLC. Innovative Technology Electronics LLC. (IT) warrants the product to be free from "Defects" in materials under normal use for a period of "One Year" from the date of the original purchase. The Warranty is "Not" transferable.

IT agrees, within the initial "One Year" period, to replace the product if it is determined to be defective at "No Charge" or offer a merchandise credit if proof of purchase is provided or if the original product is no longer in stock. IT will cover the cost to repair or replace damaged "Parts" only for a total period of "One Year" from the date of the original purchase.

The warranty does not cover cosmetic damage, antennas, AC cords, cabinets, headbands, ear-pads, or damage due to line power surges, connection to an improper voltage supply or setting, misuse, mishandling, accident, acts of God, or attempted repair by an unauthorized service agent.

Repair or Replacement as provided under this warranty is the exclusive remedy of the customer. IT shall not be liable for any incidental or consequential damages for breach of any implied warranty on this product except to the extent prohibited by applicable law. Any implied warranty of merchant-ability or fitness for a particular purpose on this product is limited in duration to the duration of this warranty.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

Contact

Website: www.victrola.com/support

Phone: (877) 483-2497 (Monday - Friday, 10am - 6pm, EST)

Made In China.