Victrola VPRO-3100 USB Turntable

Introduction

This document provides instructions for the Victrola VPRO-3100 USB Turntable.

Safety Instructions

• Read and keep these instructions.
• Heed all warnings on the appliance and in the manual.
• Follow all operating and use instructions.
• Do not use near water or moisture.
• Clean only with a dry cloth.
• Ensure at least 5 cm ventilation around the apparatus.
• Do not install near heat sources.
• Protect the power cord from damage.
• Use only manufacturer-specified attachments/accessories.
• Unplug during lightning storms or long periods of non-use.
• Refer servicing to qualified personnel.
• Keep the unit in a well-ventilated environment.
• Do not expose to dripping or splashing; do not place liquid-filled objects on the unit.
• The main plug serves as the disconnect device and must remain operable.
• This product is for household use only, not commercial.
• This equipment is Class II or double insulated and does not require an earth connection.
• [⚠️] The lightning flash symbol indicates dangerous voltage.
• [!] The exclamation point symbol indicates important operating and maintenance instructions.
• Warning: Do not expose to rain or moisture. Do not place naked flame sources (e.g., candles) on the unit.
• Caution: Unauthorized modifications may void the user's authority to operate the device and may result in hazardous exposure.

Power Adaptor Plug Installation/Removal

UK Plug

Follow these steps to install or remove the power adaptor plug for UK outlets:

1. Open the plug casing.
2. Insert the adaptor into the socket.
3. Close the plug casing until it clicks.
4. To remove, press the release mechanism and open the casing.

(Note: The process involves opening a casing, inserting the adaptor, and closing it until it locks.)

Europe Plug

Follow these steps for Europe outlets:

1. Open the plug casing.
2. Insert the adaptor into the socket.
3. Close the plug casing until it clicks.
4. To remove, press the release mechanism and open the casing.

(Note: Similar to UK plug, involves opening, inserting, and locking the casing.)

Turntable Layout

The turntable features the following components:

• 1. Turntable Platter
• 2. Tone Arm
• 3. 45 RPM Adaptor
• 4. Tone Arm Lock
• 5. Phono Stylus Cartridge
• 6. Power Button [power-symbol]
• 7. Speed Change Button [speed-select-symbol]
• 8. Start/Stop Button [start/stop-symbol]
• 9. Tone Arm Return Button (Eject) [return-symbol]
• 10. Tone Arm Lift Lever [lift-lever-symbol]
• 11. Dust Cover Hinges
• 12. Dust Cover
• 13. USB Output Jack [usb-symbol]
• 14. Power Adaptor Jack
• 15. RCA Output Jack [rca-symbol]

Assembly and Operation

Assembly of the Dust Cover

1. Remove protective plastic film from the dust cover.
2. Align the dust cover with the dust cover hinges on the back of the unit.
3. Gently push down the dust cover to clip into the hinges.

Turntable Operation - Setup

An AC/DC adaptor (12V/1.0A) is required for operation.

1. Connect external Hi-Fi amplifier or speakers using RCA cables (not included). Ensure color-coded connections (red to red, white to white).
2. Insert the DC plug of the adaptor into the DC IN Jack on the back of the unit.
3. Plug the AC/DC adaptor into a wall outlet (AC 100-240V, 50-60Hz).

Turntable Operation - Basic Operation

Before use, remove the white stylus guard. Ensure the tone arm is unlocked and free to move. Lock the tone arm when not in use.

1. Press the POWER Button to turn the turntable ON.
2. Place a record on the turntable platter and select the desired speed (33 1/3 or 45 RPM) using the SPEED SELECTION SWITCH. Use the 45 RPM adaptor for 45 RPM records.
3. Press the START / STOP Button to begin playback. Press again to stop (pause).
4. Open the TONE ARM CLIP. Use the TONE ARM LIFT LEVER Button [lift-lever-symbol] to raise the arm. Gently move the tone arm to the desired position over the record. The turntable begins to spin when the tone arm moves towards the record. Push the LIFT LEVER Button again to lower the arm onto the record.
5. To return the tone arm at any time, press and hold the RETURN Button [return-symbol] for 1-2 seconds. This automatically returns the tone arm to its holder and stops playback.
6. The Auto Return feature will automatically return the tone arm to the holder at the end of the record.
7. Adjust the volume using your external audio device.

Maintenance and Troubleshooting

Auto Return Reset

It is recommended to reset the Auto Return mechanism after moving the product, as movement can cause irregular rotation.

1. Place a record on the platter and play it.
2. Manually move the tone arm to the blank part at the end of the record and let it finish playing.
3. The Auto Return mechanism will adjust itself, and the tone arm will automatically return to the arm rest.

How to Replace the Turntable Needle

Replacement Needle Model: ITNP-LD1

Removing the Stylus from the Cartridge

1. Set a screwdriver at the tip of the stylus and push down in direction "A". Warning: Applying too much force may damage or break the stylus.
2. Pull the stylus out toward direction "B".

Installing the Stylus

1. Hold the tip of the stylus and insert the other edge by pressing toward direction "C".
2. Push the stylus up toward direction "D" until it locks into place.

Caution:

• Do not remove or bend the stylus needle.
• Do not touch the needle to avoid injury.
• Turn off the unit's power before replacing the stylus.
• Keep out of reach of children.

Note: The stylus typically lasts about 300 hours. Replace it when sound quality degrades.

If the Belt Becomes Loose

If the drive belt has become loose during transportation, follow these steps to re-install it:

1. Remove the rubber mat from the turntable platter. Unclip the E ring from the turntable shaft (using tweezers or pliers) and release the platter from the shaft.
2. Place the drive belt on the inner rim of the turntable platter and pull it through the hole on the platter.
3. Hold the belt with your fingers and place it onto the motor pulley.
4. Clip the E ring back onto the shaft and place the rubber mat onto the turntable platter.

Caution: Ensure the drive belt is not twisted or distorted. Avoid oil, as it will make the belt slippery.

Tips for Better Turntable Use

• Handle the turntable cover gently, gripping it at the center or sides.
• Do not touch the needle tip with your fingers; avoid bumping it against the platter or record edge.
• Clean the needle tip frequently using a soft brush in a "back-to-front" motion.
• If using needle cleaning fluid, apply it very sparingly.
• Wipe the dust cover and turntable housing with a soft cloth. Use only a small amount of mild detergent for cleaning.
• Never apply harsh chemicals or solvents to the turntable system.

USB Recording Operation

To record vinyl to MP3 via computer:

1. Use the included USB Output Cable and Instructional CD Software.
2. Connect one end of the USB cable to the turntable and the other end to your computer.
3. Connect the AC power cord to the turntable.
4. Install the software on your computer by selecting the proper Mac or PC install files from the CD and following the on-screen prompts.

For the most up-to-date manuals, software, instructional details, or troubleshooting, visit http://audacityteam.org.

Specifications

Manufacturer Information

Made in China.

Design and specifications are subject to change without notice.

Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.

This product is manufactured and sold by Innovative Technology Electronics LLC. Victrola and the Victrola logo are trademarks of Technicolor or its affiliates and are used under license by Innovative Technology Electronics LLC. Any other product, service, company, trade or product name and logo referenced herein are neither endorsed nor sponsored by Technicolor or its affiliates.