How to Assemble Canopy - Door Awning Glass

IMPORTANT!

Please read these instructions carefully before starting assembly. Keep these instructions in a safe place for future reference.

Before Assembly

Site Selection

Choose your site carefully before beginning assembly. Consider the door's opening - inside or outside. The product must be positioned and fixed on a flat level surface.

This is a multi-part assembly best achieved by two people. Allow at least half a day for the assembly process.

Take all components & parts out of the packages. Sort the parts and check against the content parts list. Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.

Please note multi-sided profiles are used in this Door Awning. As a result some holes in the profiles are not used during assembly.

Please review entire instructions before starting. Carry out the assembly steps in exact order.

Please consult your local authorities if any permits are required prior to constructing the product.

Safety Advice

• It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
• We strongly recommend using work gloves during panel sliding.
• Some parts may have sharp edges. Please be careful when handling components.
• Always wear shoes and safety goggles when working with extruded aluminium.
• If using a step ladder or power tools make sure that you follow the manufacturer's safety advice.
• Keep children away from the assembly area.
• Do not touch overhead power cables with the aluminium profiles.
• Do not attempt to assemble the product in windy or wet conditions.
• Dispose of all plastic bags. Keep them out of reach of small children.
• Do not climb or stand on the roof.
• Do not hang or lay on the profiles.
• Do not position your product in an area exposed to excessive winds.
• Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
• Make sure there are no hidden pipes or cables in the wall before inserting the pegs.
• This product is designed to be used mainly as a Door Awning.
• Heavy snow load on the roof can make it unsafe to stand below or nearby. The snow must be removed from the structure's roof if the snow is accumulated.
• The wall anchoring kit supplied with this product is suitable for concrete or solid brick walls. Other wall types need an accordant wall fixation kit.

During Assembly

During assembly, you will encounter different icons for different products. Please see below for more information:

You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles. Do not spray the panels.

Use a rubber mallet if necessary.

The Allen screws with the spacer sleeves must be in the center of the drill hole. The screw must not touch the glass!

Tools & Equipment

• 3 people needed
• Allen Key / Hex Key
• Spirit Level
• Silicone
• Pencil
• Spirit Level
• Ladder
• Tape measure

Care & Maintenance

• When your product needs to be cleaned, use a soft cloth and rinse with cold clean water.
• DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
• Clean the product once assembly is complete.

Parts List

Canopy - Door Awning Glass

• Item 9494: Glass Panel (1 pc)

Hardware

• Item 9355: Bracket (2 pcs)
• Item 9356: Bracket (2 pcs)
• Item 9357: Support Arm (2 pcs)
• Item 9358: Support Rod (2 pcs)
• Item 9690: Screw (4 pcs)
• Item 9691: Allen Key (8 mm / 5/16") (1 pc)
• Item 9361: Allen Key (6 mm / 7/32") (1 pc)
• Item 9362: Allen Key (2.5 mm / 3/32") (1 pc)

Assembly Steps

Step 1: Mark the wall for drilling. For Canopy 1400, mark 90 cm / 35.4" from the center of the door and 15 cm / 5.9" from the top of the door frame. For Canopy 1500, mark 100 cm / 39.37" from the center of the door and 15 cm / 5.9" from the top of the door frame.

Step 2: Drill holes at the marked positions. Use a drill bit appropriate for your wall type.

Step 3: Insert wall anchors if necessary (not supplied). Ensure they are suitable for your wall type.

Step 4: Attach brackets (9355 & 9356) to the wall using appropriate screws and anchors.

Step 5: Secure the brackets to the wall using screws (9690) and the provided Allen keys (9691, 9361, 9362).

Step 6: Attach the support arms (9357) to the brackets.

Step 7: Place the glass panel (9494 or 9363) onto the support arms. Ensure the Allen screws with the spacer sleeves are in the center of the drill hole and do not touch the glass.

Step 8: Secure the glass panel to the support arms using the provided hardware.

Step 9: Attach the support rods (9358) to the glass panel and the brackets.

Step 10: Ensure all connections are secure.

Step 11: Apply silicone sealant to the connection points for added stability and weatherproofing.

Step 12: Double-check all fastenings to ensure the awning is securely installed.

Step 13: Apply silicone sealant to the top of the support arms where they meet the glass for a watertight seal.

3 Year Limited Warranty

Palram Canopia Ltd. warrants that the product will be free from defects in material or workmanship for a period of 3 years from the original date of purchase. This warranty is valid only if the product is installed, handled, cleaned, and maintained in accordance with Canopia's written specifications. This warranty does not cover defects resulting from normal wear and tear, misuse, accidents, or acts of nature. For full warranty details, please refer to the warranty document.