DeepCool GAMMAXX GTE V2 CPU Cooler Installation Guide
This guide provides instructions for installing the DeepCool GAMMAXX GTE V2 120mm single tower CPU cooler.
Product Overview
The GAMMAXX GTE V2 is a 120mm single tower CPU cooler designed for efficient heat dissipation and enhanced system performance.
Compatibility
- Intel Sockets: LGA 1700, LGA 1200, LGA 1151, LGA 1150, LGA 1155, LGA 1156
- AMD Sockets: AM5, AM4
Package Contents
Ensure all parts are present before installation:
- Heatsink (x1)
- Fan (x1)
- Intel Mounting Bracket (x1)
- AMD Mounting Bracket (x1)
- Fan Clips (x2)
- Intel Mounting Screws (x2)
- AMD Mounting Screws (x2)
- AMD Mounting Screws (x2)
- Intel Standoffs (x4)
- AMD Standoffs (x4)
- Thermal Paste (x2 tubes)
Installation for Intel Sockets (LGA 1700/1200/115x)
Follow these steps to install the cooler on Intel motherboards:
Step 1: Prepare the CPU
Apply a small amount of thermal paste (included) to the center of the CPU's Integrated Heat Spreader (IHS). A pea-sized amount is usually sufficient.
[Diagram 1: Shows thermal paste application on CPU]
Step 2: Install Standoffs
Screw the four Intel standoffs into the designated mounting holes on the motherboard. Ensure they are securely tightened.
[Diagram 2: Shows screwing standoffs into motherboard for Intel]
Step 3: Mount the Heatsink
Place the heatsink onto the CPU, aligning the mounting holes on the heatsink bracket with the standoffs. Secure the heatsink using the two Intel mounting screws. Tighten them diagonally for even pressure.
[Diagram 3: Shows heatsink being mounted and secured with screws on Intel standoffs]
Step 4: Attach Fan Clips
Clip the two fan clips onto the sides of the heatsink's fins, where the fan will be mounted.
[Diagram 4: Shows fan clips being attached to heatsink fins]
Step 5: Mount the Fan
Attach the fan to the heatsink by clipping it onto the fan clips installed in the previous step. Ensure the fan's airflow direction is appropriate (usually towards the rear of the case).
[Diagram 5: Shows fan being attached to the heatsink via clips]
Step 6: Connect Fan Cable
Connect the fan's 4-pin power cable to the CPU_FAN header on the motherboard. This header is typically labeled "CPU_FAN", "CPU_OPT", "CHA_FAN", or "SYS_FAN".
[Diagram 6: Shows fan cable connected to motherboard CPU_FAN header]
Step 7: Final Check
Ensure the cooler is firmly seated and all connections are secure.
[Diagram 7: Shows completed Intel installation]
Installation for AMD Sockets (AM5/AM4)
Follow these steps to install the cooler on AMD motherboards:
Step 1: Prepare the Motherboard
If a previous cooler is installed, remove it. Remove the stock AMD mounting brackets from the motherboard if present.
[Diagram 1: Shows removal of stock brackets/cooler]
Step 2: Install AMD Mounting Brackets
Attach the AMD mounting brackets to the motherboard using the provided AMD standoffs and screws. Ensure the brackets are oriented correctly for the socket.
[Diagram 2: Shows AMD mounting brackets being installed]
Step 3: Apply Thermal Paste
Apply a small amount of thermal paste (included) to the center of the CPU's Integrated Heat Spreader (IHS).
[Diagram 3: Shows thermal paste application on AMD CPU]
Step 4: Mount the Heatsink
Place the heatsink onto the CPU, aligning the mounting mechanism with the AMD brackets. Secure the heatsink using the two AMD mounting screws. Tighten them diagonally for even pressure.
[Diagram 4: Shows heatsink being mounted and secured on AMD brackets]
Step 5: Attach Fan Clips
Clip the two fan clips onto the sides of the heatsink's fins, where the fan will be mounted.
[Diagram 5: Shows fan clips being attached to heatsink fins]
Step 6: Mount the Fan
Attach the fan to the heatsink by clipping it onto the fan clips installed in the previous step. Ensure the fan's airflow direction is appropriate.
[Diagram 6: Shows fan being attached to the heatsink via clips]
Step 7: Connect Fan Cable
Connect the fan's 4-pin power cable to the CPU_FAN header on the motherboard. This header is typically labeled "CPU_FAN", "CPU_OPT", "CHA_FAN", or "SYS_FAN".
[Diagram 7: Shows fan cable connected to motherboard CPU_FAN header]
Connection Information
The fan features a 4-pin PWM connector for speed control, compatible with CPU_FAN, CPU_OPT, CHA_FAN, or SYS_FAN headers. It also includes RGB lighting, indicated by a "+12V GRB" connection, which should be connected to a compatible RGB header on the motherboard.
[Diagram: Shows fan connector and RGB connection details]
Support and Information
For more information, please visit the official DeepCool website:
DeepCool USA Inc. is located at 11650 Mission Park Drive Suite 108, Rancho Cucamonga, CA 91730.
Beijing DeepCool Industries Co., Ltd. is located at Building 10, No. 9 Dijin Road, Haidian District, Beijing 100095, China.
© 2021 Beijing DeepCool Industries Co., Ltd. All rights reserved.
