MantelMount TM1A Installation Instructions

Important Safety Instructions - Save These Instructions

❗ WARNING! This product contains small parts that can be a choking hazard. Do not let children play with any of these small parts! Keep children away from the work area during installation.

⚠️ CAUTION: Do not let children operate, pull on, or hang from MantelMount. Do not let children push MantelMount upward to the top position - this will cause the mount to slam against the wall due to the upward force of the springs. Only a person tall enough to control the mount all the way to the top should operate MantelMount.

⚠️ CAUTION: This product is intended to be installed by professional installation contractors, or persons familiar with the tools and methods required for this installation. If you are not sure about your ability to perform this installation, you must contact a professional. MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.

⚠️ CAUTION: Do not use this product in any way, or for any purpose, that is not specifically described in these instructions. MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.

Visit: www.MantelMount.com

Required Tools

Diagrams show various tools. Required tools include screwdrivers and a wrench.

• 11/64" drill bit

Optional Tools

Optional tools are also depicted.

Component Verification

Before you begin, please verify that all components are included and undamaged. If any parts are missing or damaged, contact MantelMount. Never proceed with missing or damaged parts!

Lay out all components and make sure you identify that each one has a match in the diagram. Some of the parts included will not be used during installation. Do not proceed if you do not understand and identify all of the components.

Diagram shows various hardware components labeled with numbers and quantities:

• {01} M5x12 Screw (x4)
• {02} M5x30 Screw (x4)
• {03} M5x40 Screw (x4)
• {04} M6x16 Screw (x4)
• {05} M6x30 Screw (x4)
• {06} M6x40 Screw (x4)
• {07} M8x15 Screw (x4)
• {08} M8x25 Screw (x4)
• {09} M8x45 Screw (x4)
• {10} M5-M6 Washer (x4)
• {11} M8 Washer (x4)
• {12} M5-M6 Washer (x4)
• {13} M8 Washer (x16)
• {14} Screws (x7)
• {15} Screws (x6)
• {16} Screws (x4)
• {17} Lag Bolts (x4)
• {18} Washers (x4)
• {19} Screws (x4)
• {20} Safety Bolt (x1)
• {21} Safety Nut (x1)
• {22} Hex Tool (x1)
• {23} Wrench (x1)
• {24} Cable Ties (x4)
• {25} Velcro (Hook) (x8)
• {26} Velcro (Loop) (x8)

Diagrams also show larger components:

• {27} Routing Boxes (x2)
• {28} Handle (x1)
• {29} Wall Covers (x2)
• {30} Rubber Bumper (x1)
• {31} Vertical Braces (x2)
• {32} Wall Plate (x1)
• {33} TV Brace (x1)
• {34} Horizontal Bar (x1)
• {35} Lifting Mechanism (x1)

Critical Installation Requirements

Please verify that your installation meets all of these CRITICAL requirements:

1. Requirement A: Fireplace Type and Temperature

   MantelMount is designed for use only with decorative fireplaces that are not the primary heat source for a house. Temperature at the front edge of the mantle should never exceed 110°F.

   Diagram illustrates a mantle with a thermometer showing a maximum of 110°F.

2. Requirement B: Wall Structure

   Wall must be WOOD STUD FRAME only. There must be at least 2 studs available for mounting. Wall covering must not exceed 5/8 inches thick.

   Diagram illustrates a wall with two studs marked.

3. Requirement C: Mantle Extension

   Mantle must not extend from mounting surface more than 14 inches.

   Diagram illustrates a mantle extension measurement, showing a maximum of 14 inches.

4. Requirement D: TV Specifications

   TV weight must be between 40 - 115 pounds and have a screen size larger than 47 diagonal inches. Consult TV Owner's Manual for verification.

   Diagram shows a hand holding a TV owner's manual with weight and size information.

5. Requirement E: Vertical Space Above Mantle

   The space above the mantle must be taller than the TV. The required space depends on how far out the mantle extends. Refer to the chart below and add this additional height to TV height to determine if space is tall enough.

   Diagram shows a side view illustrating 'Space height' and 'TV height' relative to the mantle.

   If mantle extends:	This is required space height:
   Less than 8 inches	TV height plus 2 inches
   8 - 10 inches	TV height plus 4 inches
   10 - 12 inches	TV height plus 5 inches
   12 - 14 inches	TV height plus 7 inches

Installation Steps

1. Step 1: Determine TV Back Type

   Use Vertical Brace {31} to determine if the television is a flat back or an irregular back. An irregular back will require spacers and longer screws to fill the space between the Vertical Brace and the TV. Diagrams show 'Flat Back' and 'Irregular Back' configurations, illustrating the need for spacers.

2. Step 2: Select Correct TV Screws

   Choose the correct screw diameter and length for the TV. Hand-thread screw combination into the TV to ensure there is adequate thread engagement without hitting the bottom of the threaded insert. Use only the minimum amount of spacers (if required). A diagram shows 7-10 threads minimum engagement is required in the TV insert, leaving a gap.

   ⚠️ CAUTION: Do not use screws that are too long for the threaded inserts of the Television. This can damage internal components.

3. Step 3: Possible Screw Combinations

   Diagrams show various possible screw and spacer combinations for attaching the TV brace to the TV, with notes that the spacer sleeve always faces the screw.

4. Step 4: Mount Vertical Braces

   Mount Vertical Braces {31} making sure the bottom of the Brace is LESS THAN ONE INCH ABOVE the bottom of the television. A diagram illustrates this placement.

5. Step 5: Determine Vertical Position of Wall Plate

   Determine the vertical position of the wall plate. The further out a mantle extends, the more it can interfere with the TV's arc. MantelMount must be installed a minimum distance above the mantle, based on Requirement E. A chart is provided for required installation height based on mantle extension:

   • Less than 8 inches mantle extension: 2 inches above mantle
   • 8 - 10 inches mantle extension: 4 inches above mantle
   • 10 - 12 inches mantle extension: 5 inches above mantle
   • 12 - 14 inches mantle extension: 7 inches above mantle

   Note: If wall space above the mantle is limited, use exact dimensions. If ample space exists, these are minimum requirements.

6. Step 6: Determine Horizontal Position of Wall Plate

   Determine the horizontal position of the wall plate to compensate for an unbalanced TV 'Center of Gravity'. If the TV leans, temporarily mount the Horizontal Bar {34} and lift the TV to find the balance point. This distance will be used to offset the Wall Plate {32}. If unable to determine, installation can proceed, and adjustments can be made later. Remove the Horizontal Bar {34} and screws {15} after this step.

   Diagrams illustrate checking TV balance and offsetting the wall plate.

7. Step 7: Mark Mantle Centerline

   Measure the centerline of the mantle and mark it with tape on the wall.

8. Step 8: Locate Studs

   Locate at least two studs with a stud finder. Use a sharp awl or finish nail to find the center of each stud. Lag bolts must be installed into the CENTER of the studs. A diagram shows a cutout for reference.

9. Step 9: Align and Mark Wall Plate

   Align the arrows on the Wall Plate {32} pointing upward. Center and level the plate above the mantle, positioning the height using the table from STEP 5. Mark the 4 spots for lag bolts directly on the center of the studs.

   Diagram shows the wall plate being positioned and marked, with a note for 'Minimum Height from STEP 5'.

10. Step 10: Pre-drill Holes

    Pre-drill the 4 holes with an 11/64" drill bit to a depth of 2.5 inches (65mm), including wall covering. Note: Wall covering (drywall) must not exceed 5/8" thickness.

    Diagram shows a drill bit and wall.

11. Step 11: Install Lag Bolts

    Adjust Wall Plate {32} horizontally, using results from STEP 6, to compensate for an unbalanced TV center-of-gravity, up to a maximum of 2 inches left or right. Move the Wall Plate in the SAME DIRECTION as the offset from STEP 6. Loosely install Lag Bolts {17} and Washers {18}. Diagrams show the 2-inch maximum adjustment range.

12. Step 12: Caution on Lag Bolts

    ⚠️ CAUTION: Do not overtighten Lag Bolts {17}. Tighten only until the washers are firmly against the wall plate. Damage due to overtightening can cause property damage or injury.

13. Step 13: Install Lifting Mechanism

    Insert the top tab of the Lifting Mechanism {35} into the slot of the Wall Plate {32}, then slide the bottom into position. A diagram illustrates this insertion.

    DO NOT damage or scratch the rods of the Gas Springs!

14. Step 14: Secure Lifting Mechanism

    Align all four holes and install Screws {14}. Tighten with the supplied Wrench {23}.

15. Step 15: Trace Routing Box Location

    Trace the Routing Box {27} (without the tabs) for both desired locations onto the wall along the edge of a stud. Boxes must be mounted to studs.

16. Step 16: Cut Openings for Conduit

    Cut out both openings through the wall covering (drywall) along the studs using a Keyhole Saw.

    Diagram shows cutting openings in drywall along studs.

17. Step 17: Attach Conduit to Box

    Attach the CUT end of the conduit to the box and install to the stud using Screws {19}. If the box is within the MantelMount Wall Frame {32}, use inner tabs to protrude to the Wall Cover {29}. If outside the frame, break off inner tabs and mount flush using outer tabs. Diagrams show inner and outer tabs.

18. Step 18: Feed Conduit

    Feed the conduit through the other opening and cut the other end of conduit to length using a hacksaw.

19. Step 19: Install Second Box and Cover Plate

    Install the second box to the stud using Screws {19}, and install a cover plate if available.

20. Step 20: Feed Signal Cables

    Signal Cables can usually be fed through the conduit by pushing them from the higher opening to the lower opening. A diagram shows cables being fed through conduit.

    Reference Only: Cables must be long enough for extension and swivel, and to attach to the TV Brace {33} using Cable Ties {24}. DO NOT attach cables to the central Lifting Mechanism {35} as they can get pinched.

21. Step 21: Install TV Brace

    Install the TV Brace {33} to the Lifting Mechanism {35} while ensuring that the side marked "IN" is facing the Lifting Mechanism. Diagram shows the brace being attached with the "IN" side correctly oriented.

22. Step 22: Level and Tighten TV Brace

    Level the TV Brace and tighten the 3 screws {14} using the supplied wrench {23}.

23. Step 23: Two-Person Step - Secure Lifting Mechanism

    This step requires two people. Pull down the TV Brace until the upper arm is below the Safety Hole. DO NOT HIT MANTLE! The second person inserts the Safety Bolt {20} and installs the Safety Nut {21}. Slowly release the TV Brace. The Lifting Mechanism should be held at a horizontal position. Diagrams illustrate the process.

24. Step 24: Warning - Safety Bolt/Nut

    ❗ WARNING: Do not put hands into Lifting Mechanism without the Safety Bolt and Safety Nut installed. The power of the Lifting Mechanism can cause bodily injury!

25. Step 25: Two-Person Step - Hang Television

    This step requires two people. Carefully hang the Television onto the TV Brace, making sure that all four hooks on the Vertical Braces {31} engage the TV Brace. DO NOT allow the Television to drop far enough to cause the Lifting Mechanism {35} to hit the mantle. MantelMount is pre-adjusted, but be prepared to remove the television to make corrections.

    Diagram shows two people hanging a TV onto the mount.

26. Step 26: Adjust Bottom Stop Position

    If the Lifting Mechanism {35} appears too close to the mantle, remove the television. Go to STEP 31 to adjust the Bottom Stop position. Repeat until the Lifting Mechanism is a safe distance from the mantle when the TV is in place.

27. Step 27: Check TV Level and Balance

    Check the TV with a Level. Carefully slide the TV sideways, if required, until it is balanced and horizontal, up to a MAXIMUM OF 2 INCHES left or right. This distance should match the compensation distance used in STEP 11. If compensation was not made in STEP 11 but is needed now, remove the TV, repeat STEP 11, and slide the Wall Plate {32} in the OPPOSITE direction of the TV's sideways movement. Diagrams show the 2-inch adjustment range.

28. Step 28: Attach TV Brace to Vertical Braces

    Install 4 Screws {15} through the TV Brace {33} and into the Vertical Braces {31}.

29. Step 29: Install Horizontal Bar

    Install the Horizontal Bar {34} with Screws {15}. The Horizontal Bar MUST BE aligned with the end of the TV Brace {33} or the Lifting Mechanism will not work properly. Diagram shows alignment.

30. Step 30: Install Handle and Bumper

    Install the Handle {28} with Screws {16} into the Horizontal Bar. The Handle MUST be within one inch (1") of the bottom of the Television frame so that it does not hit the mantle. Firmly insert the Rubber Bumper {30} into the center slot of the Horizontal Bar {34}. Diagram shows handle placement and bumper insertion.

31. Step 31: Adjusting for Bottom Stop Position

    Loosen the Locknut and adjust the Bottom Stop screw to the desired stopping position. Turning the screw clockwise raises the Bottom Stop position; turning counter-clockwise lowers the TV closer to the mantle in the lowered position. Tighten the locknut after adjustments. Diagrams show the adjustment screw and locknut.

32. Step 32: Adjusting for Television Weight

    With the Safety Bolt {20} in place, use the included Hex Tool {22} and a socket wrench to adjust the long bolt inside the Lifting Mechanism {35}. Turning this bolt increases or decreases the lifting force. Turn clockwise for heavier TVs, counter-clockwise for lighter TVs. Adjust until the TV gently stays in the lowered position, almost staying up against the Safety Bolt, but slowly lowering to the Bottom Stop. Diagrams show the adjustment bolt and the range of movement.

33. Step 33: Transfer Box Location

    Measure carefully or use transfer paint to transfer the box location onto the Wall Cover {29}.

34. Step 34: Cut Hole in Wall Cover

    Use a 1.5 inch Hole Saw drill bit to cut a hole through the Wall Cover {29} directly in the center of the marked area. Be careful not to damage the edge around the hole.

35. Step 35: Paint Wall Covers

    Paint the Wall Covers {29} if desired.

36. Step 36: Install Wall Covers

    Install the Wall Covers using the included adhesive Velcro strips. Apply Loop {26} pieces to the Wall Frame and Hook {25} pieces to the Wall Covers. Diagrams show hook and loop attachment.

37. Step 37: Remove Safety Bolt and Nut

    With the television in the lowered position, remove the Safety Nut {21} and Safety Bolt {20} from the Lifting Mechanism {35}. KEEP THIS BOLT AND NUT in a safe place for future use (e.g., to remove the television or change Gas Springs). Recommendation: Tape them to the inside of the Wall Cover {29}.

    ⚠️ CAUTION: Never swing the television until it hits the mantle on either side.

    ⚠️ CAUTION: Never release the handle before it is fully upright. MantelMount is strongest in the top position, and allowing it to slam closed can damage televisions. Always control the lifting process.

    ⚠️ CAUTION: Never allow children to play around or operate MantelMount. Property damage or personal injury can occur.

Additional Installation Parts and Diagram

Diagram shows an exploded view of many components, labeled with numbers.

A table lists additional installation parts with Item No., Part Number, Description, and Quantity:

Product Features

Diagram illustrates key features of the MantelMount:

• 115° Vertical Rotation: Allows for a wide range of viewing angles.
• Auto-Straightening: Flattens the TV as it is raised to the upper position to prevent rotation into the wall.
• 40° Horizontal Rotation: Provides flexible positioning.
• Extends outward up to 15 inches: Brings the TV closer to the room for optimal viewing.
• Wall Covers: Can be painted to match the wall and conceal the mount frame.
• Temperature-Sensitive Handles: Change to red color at temperatures above 110°F to warn users that the fireplace is too hot for TV safety.
• Horizontal Adapter: Available separately to adapt MantelMount to solid horizontal surfaces.