Instruction Manual for MantelMount models including: MM815, MM815 Motorized Remote Control Pull Down TV Mount, Motorized Remote Control Pull Down TV Mount, Remote Control Pull Down TV Mount, Control Pull Down TV Mount, Pull Down TV Mount, Down TV Mount, TV Mount
Amazon.com: MantelMount MM815 Motorized Remote Control Pull Down TV Mount with Automated Swivel | Above Fireplace Mount for TVs 45"-90" Up to 115 lbs | RF Remote Control & Favorite Memory Positions : Electronics
MM815 Installation Manual (PDF) MantelMount MantelMount,MM815,Motorized,Remote,Control,Pull,Down,TV,Mount,with,Automated,Swivel,|,Above,Fireplace,Mount,for,TVs,45"-90",Up,to,115,lbs,|,RF,Remote,Control,&,Favorite,Memory,Positions,B0C5498MM5,
MM815 Motorized Drop Down TV Mount
INSTALLATION INSTRUCTIONS
Read this entire manual before you begin.
Do not unpack box contents until verifying the requirements listed on page 2.
! WARNING!
This product contains small parts that can be a choking hazard. Do not let children play with any of these small parts! Keep children away from the work area during installation.
! Caution
This product is intended to be installed by professional installation contractors, or persons familiar with the tools and methods required for this installation. If you are not sure about your ability to perform this installation, you must contact a professional. MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.
! Caution
Do not let children operate, pull on, or hang from MantelMount.
! Caution
Do not use this product in any way, or for any purpose, that is not specifically described in these instructions. MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.
Features Include:
Motorized Travel: From the comfort of your couch, move the TV to the perfect viewing position.
Smooth Operation: Solid shafts with polymer bushings at pivot points provide silent movement
Swivel Clutch: Swivel drive automatically disengages to prevent damage if something gets in the way of swiveling
Visual Temperature Sensor: Change to red color at temperatures above 110ºF to warn users if the fireplace is too hot for TV safety
If you need help, call 1.800.897.9755 ext.1
For missing/damaged parts or questions during installation, contact our Customer Support team at 1.800.897.9755 ext.1 or support@mantelmount.com. Customer satisfaction is our highest priority! Access a PDF of this manual at MantelMount.com/FAQs/Specs and Manuals. For more information on MantelMount patented technology visit: www.mantelmount.com/pages/patents
Contains important safety information please save! MantelMount.com
BEFORE INSTALLATION
1 Verify TV and mount space meet these criteria:
MANTEL DEPTH 16" MAXIMUM
45" 90"
SCREEN SIZE 45" to 90" (Diagonally)
For TVs Shorter then 24. 7" without a soundbar, mount will be visible in top position.
WOOD STUDS FOR MOUNTING
Studs Maximum 28" apart; Wall Covering Maximum 5/8"
MAX 20-115 LBS
VVEESSAA
WWiiddtthh:: 220000--770000mmmm HHeeiigghhtt:: 110000--550000mmmm
VESA
Width: 200-700mm Height: 100-500mm
WEIGHT CAPACITY 20 to 115 LBS. (Including Sound Bar)
VESA COMPLIANT Up to 600 X 600mm
16" MAX
2 Verify MantelMount will fit the wall space.
A. Use the reference diagram (right) and chart (below) to write down the following measurements (in inches):
Wall Space Height: TV Height: Mantel Depth: Required Vertical Space:
(Distance from mantel to ceiling/crown molding.) (Include sound bar height if placing below TV.) (Distance mantel extends away from the wall.) (Calculation from chart below.)
B. If the Required Vertical Space is less than or equal to the Wall Space Height, then MantelMount will fit the wall space.
If Mantel Depth is: Less than 8" 8" 10" 10" 12" 12" 15" 16"
Required Vertical Space is: TV height + 2" TV height + 4" TV height + 6" TV height + 9" TV height + 11"
STUDS MAX 28" APART
WALL SPACE HEIGHT TV HEIGHT
MANTEL DEPTH
3 Verify you have the required tools.
45mm
1013mm
7/32"
OPTIONAL
STUD FINDER PENCIL LEVEL AWL ALLEN WRENCHES WRENCH SOCKET WRENCH PHILLIPS DRILL BIT
2 MM815 Installation Instructions
POWER DRILL TAPE MEASURER TAPE DISPENSER
PAINT BRUSH
HOLE SAW
BEFORE INSTALLATION
4 Verify all parts are included.
SILVER SCREWS FOR BACK OF TV
BLACK PARTS FOR MOUNT
{01} x4 M5x12
{01} x4
M5x12
{04} x4 M6x16
{04} x4
M6x16
{07} x4 M8x15
{07} x4
M8x15
{02} x4 M5x30
{02} x4
M5x30
{05} x4 M6x30
{05} x4
M6x30
{08} x4 M8x25
{08} x4
M8x25
{17} x4 Lag Bolt {17} x4 {1L7a}gxB4oLltag Bolt
{03} x4 M5x40
{03} x4
M5x40
{06} x4 M6x40
{06} x4
M6x40
{09} x4 M8x45
{09} x4
M8x45 {10} x4 M5-M6
{17} x4 Lag Bolt
{{1100}} x84
M5-MM66
{{111MM1}}88xx88{10}
x4
{12} x12
Spacer
{11} x8
M5-M6
M8
{16} x4 M6x12
{14} x4 M8x16{14} M8x4
{23} x8 {23} x8 Locknut MLo6cknut M6
{15}
{15} x16 x12M6x10
M6x12
{18} x4 M6x4{018} x4 Thread patterns may vMar6y.x40
{12} x12 Spacer
{10} x4 M5-M6
{11} x8 M8
{12} x12 Spacer
Safety Bolt
Cabl{e2Ti4}esx4 Safety{2B0ol}tx1
{20} x1
{24} x4
{24} x4 Cable Ties {11} x8 {24} x4 Cable Ties M8
{12} x12 Spacer
Cable Ties
{12} x12 Spacer
{33} x1 TV Brace
{227} x1 RF Remote
{22} x2 {22} x2Anchor
Anchor
{60} x1 Wall Plug
{219} x1 Visual Heat Sensor
{57} x2 Wall Cover {63} x8 Wall Clip
{35} x1 Lifting Mechanism
{32} x1 Wall Plate {55} x1 Horizontal Brace
{31} x2 Vertical Brace
{30} x2 Brace Extender
{52} x2 Sound Bar Wing
{25} x8 Velcro Hook {26} x8 Velcro Loop
If any parts are missing or damaged, contact Customer Support at 1-800-897-9755 x1 before installing.
Customer Support 1.800.897.9755 x1 support@mantelmount.com 3
MM815 Pull Down TV Mount
37. 5
14. 0
34°
26
Maximum Drop
5.1
Thickness
24.7
26
30 40 MA X
MantelMount has three different adjustments that must be made after the installation is complete in order to operate properly.
15
Bottom Clearance
18
Max. Clearance
Note: As the mount lowers, first it tilts down. As it keeps lowering, it normalizes, becoming vertical about 6 inches down.
The bottom travel stop is adjusted with the remote control.
The Centering Cams automatically swivels the TV to center while raising to avoid permanent obstacles.
The side-to-side swivel stops are adjusted via remote control and with two screws so that the TV does not swivel into the mantel.
30° R 30 °L
30° R 30 °L
Ask us about our new
* Recess Box Kit *
that hides MantelMount inside the wall !
© 2022 MANEHU PRODUCT ALLIANCE, LLC. For more information on MantelMount patented technology visit: www.mantelmount.com/pages/patents 4 MM815 Installation Instructions
BEFORE INSTALLATION
1 Learning Your Remote Functions.
Quick Note: To return mount to the home position press: Run then arrow. This will Auto-Swivel and move mount to the topmost position.
Remote Buttons Up Button
Down Button
Swivel Right
Swivel Left
1 Memory 1
2 Memory 2
RUN Run Button
SET Set Button
Pairing RF Remote
Controller should be already paired out of the box. · Unplug Power to mount for
30 seconds · Hold the button while
plugging in power. · keep holding button
for 10 seconds
The RF remote requires a CR2032 battery
Remote Control Buttons
Move the mount up to the top most position · Hold to drive to position
Move the mount down to the bottom most set position
· Mount cannot be driven lower then set limit
· Comes set for lowest bottom position · Hold to drive to position
Swivel the mount to the right most set position · Mount cannot be driven past
set right limit · Comes set for 30 degrees of swivel
to the right
· Hold to drive to position
Swivel the mount to the left most set position · Mount cannot be driven past
set left limit · Comes set for 30 degrees of swivel
to the left
· Hold to drive to position
1 Move the mount to the set 1 position
· Mount will drive to this position from either direction
· Does not come set out of the box · Hold to drive to position
2 Move the mount to the set 2 position
· Mount will drive to this position from either direction
· Does not come set out of the box · Hold to drive to position
Run Automatically move to the position
selected (
1 2)
· Press Run
· Press one of (
1 2 ) within
3 seconds
· The mount will move to the limit
automatically
· Press any button to stop movement
· For Auto-Moving, the mount will first
swivel to center position (0 degrees),
adjust height, then swivel.
Set Used to Set and Clear Positions.
Remote Control Functions
Home Position: To return mount to the home position press: Run then arrow. This will Auto-Swivel mount to center position and raise mount to the topmost position.
Stop: Press any button to stop movement
Set Memory Position: To Set Positions 1, 2 · Drive the mount to the desired Position
· Press Set · Press the Memory button (1, 2)
System Reset: If the mount is not working as expected, updates calibration while keeping set limits
· Press Set · Press Run · Press/Hold Set · Mount will move to the top position · Keep holding for 5 seconds after mount
reaches top position
Set Left/Right/Bottom Limit:The Mount will not drive past
· Drive Mount to desired limit
· Press Set
· Press one of (
)
· Press/Hold Set for 4 to 8 Seconds
· Check it was correctly done by trying to
move the mount past limit
Clearing Any Memory Position: A position does NOT need to be cleared to change it.
· From any Position
· Press Set
· Press button to clear
(
1 2)
· Press/Hold Set for at least 11 Seconds
Automatically Move to Position
The mount can be automatically moved to any
set position without having to hold the button.
To do this, press Run and then the Position
Button (
1 2 ). To stop movement,
simply push any button on the remote.
When Auto-moving, the mount will center the swivel, go to the required height, then swivel to position.
Note: Press each button firmly; a quick tap probably will not work.
Customer Support 1.800.897.9755 x1 support@mantelmount.com 5
MM815 INSTALLATION STEPS
STEP 1 Attach Braces to TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE 5 STEP 2 Determine Wall Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE 8 STEP 3 Attach Mount to Wall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PAGE 11 STEP 4 Attach TV to Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PAGE 13 STEP 5 Make Final Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PAGE 16
WARNING
Keep children away from the work area during installation. This product contains small parts, please keep out of reach from children.
WARNING
Do not remove any bolts that hold the Lifting Arm together.
WARNING
Moving the mount before all limits are set may result in damage. Complete all steps in the manual before using the mount.
WARNING
Do not let small children pull on or hang from MantelMount.
WARNING
Pinching and Crushing Hazard: The wall mount actuation is very strong, do NOT run the mount when anyone is near the mount. Do NOT have any part of the body in the mount or between the TV and Wall. The Mount will keep driving until someone pushes another button on the remote to stop it. When working on the mount unplug the power.
CAUTION
This product is intended to be installed by professional contractors or persons familiar with the tools and methods required for this installation.
If you are uncertain about your ability to perform this installation, please contact a professional.
Do not use this product in any way or for any purpose that is not specifically described in these instructions.
CAUTION
Do not use this product for purposes not specifically described in these instructions.
MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.
MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.
WARRANTY: MantelMount offers a Lifetime Limited Warranty for all TV mounts and accessories. This Lifetime Limited Warranty covers all mechanical parts but excludes lifetime coverage for gas springs or electrical parts which are warrantied for five (5) years from the original purchase price.
Symbols Used in this Manual
CAUTION / WARNING
HELPFUL INFORMATION
DO NOT
SPECIAL NOTE
REQUIRES TWO PEOPLE
Two people required for parts of this installation. Installation Tips & Videos: http://mantelmount.com/install-tips Questions during installation? Contact Customer Support: Monday Friday, 7am 4pm PST 1.800.897. 9755 x1 or support@mantelmount.com
6 MM815 Installation Instructions
STEP 1
Attach Braces to TV*
In order for the TV to hide the Mount on the wall, the Braces must be at least 3" higher than the bottom of TV (or Soundbar if one is installed).
If you are using an RB100 Recess Box then they must be 6" higher to hide the Recess Box.
1.1 Test-fit Brace components on back of TV.
Place TV screen-side down on a flat, blanketed surface. Lay out components to check assembly configuration. If installing a sound bar, refer to STEP 1.8.
1.3
Select Screws and Spacers.
If Spacers {12} are required, choose one of these Screw combinations shown with maximum Spacer usage.
BACK OF TV
{31}
{31}
{30}
{30}
{219}
{55}
1.2
Determine if TV has a flat or irregular back.
An irregular back will require Spacers {12} and longer Screws to fill spaces between the Vertical Brace {31} and the TV. The Braces must be parallel to television screen.
{31} Flat Back TV
Irregular Back TV
{31}
{12}
Irregular Back TV (Recessed Threads)
{31} {12}
{01} {10}
M5
{03}
{02}
{12} {12} {10}
{10}
{12}
{12}
{12}
{04} {10}
M6
{06}
{05}
{12} {10}
{12} {12} {12} {10}
{07} {11}
M8
{09}
{08}
{12} {11}
{12} {12} {12} {11}
Customer Support 1.800.897.9755 x1 support@mantelmount.com 7
1.4
Hand-thread screw combination into the TV.
Ensure there is adequate thread engagement without hitting the bottom of threaded insert.
CAUTION
Do not use screws that
are too long for the TV's
threaded inserts because
it may damage internal
{12}
components!
TV SCREW
1.5 Attach the Vertical Braces to the back of TV. Install the Vertical Braces {31} so that the bottoms of the braces are between 3" to 10" from the bottom of TV, (*or Soundbar if one is installed) centering the braces vertically as much as possible. SIDE VIEW
{31} {31}
MUST LEAVE A GAP IN
THREADED TV INSERT
MAXIMIZE THREAD ENGAGEMENT FOR
STABILITY
AFTER ASSEMBLY (ENLARGED)
1.6 If the lower VESA holes are less than 3" from the bottom of the TV:
OPTIONAL
{31}
UPPER VESA HOLE WITH
SCREW IN PLACE
Connect the Vertical Braces {31} through the UPPER VESA holes only, so that the bottom of the braces are between 3" to 10" from the bottom of the TV. *
If the only option is to attach the Vertical Braces to the Upper Vesa holes through a slot: 1) Hand-thread the screw through the slot; 2) slide the Vertical Brace upward until the screw meets the bottom of the slot; and 3) tighten
the screw.
You must attach the Brace Extenders {30} to the Vertical Braces as described in STEP 1.7. However, you must also attach the LOWER VESA hole through the Brace Extender as shown.
SIDE VIEW
LOWER VESA HOLE WITH SCREW IN PLACE
{30}
*If installing this mount with a MantelMount RB100 Recess Box,
the bottom of the Vertical Brace must be 6"-10" from the bottom of TV (or 6" from the bottom of the Soundbar if one is installed)..
8 MM815 Installation Instructions
{31}
VERTICAL BRACES MUST ALWAYS BE INSTALLED HIGHER THAN THE BOTTOM OF THE TV.
3 to 10
* INCHES
If the lower VESA holes are less than 3" from the bottom of the TV, go to STEP 1.6; otherwise skip to STEP 1.7.
*If installing this mount with a MantelMount RB100 Recess Box,
the bottom of the Vertical Brace must be 6"-10" from the bottom of TV (or 6" from the bottom of the Soundbar if one is installed).
1.7
Attach the Horizontal Brace to Brace Extenders.
Slide one Brace Extender {30} onto the left end of the Horizontal Brace {55}, then slide the other Brace Extender onto the opposite right end.
{30}
{30}
{55}
{55}
{31} {31}
{30} {30}
{15}
{15} {55}
Align the Brace Extenders with the Vertical Braces (that are already mounted to the back of the TV) while positioning the Horizontal Brace so that it extends an equal amount on either side of the Brace Extenders. Attach Horizontal Brace to Brace Extenders w/Screws {15}.
1.8
OPTIONAL
Use Screws {16}, M6 Washers {10}, and Nuts {23} to attach the Sound Bar Wings {52} to the Horizontal Brace {55}. Position the Wings to fit the mounting holes of the sound bar. Install sound bar. See below for Sound Bar Wing installation information.
1.9
Attach Brace Extenders to the Vertical Braces.
Slide the Brace Extenders {30} (with the Horizontal Brace {55} now attached to them) onto the Vertical Braces {31}. Position it so that the Horizontal Brace will be hidden by the TV. Use Screws {18} and Nuts {23} to attach.
{16} {52}
{55}
{10}
{52}
{23}
Arrange Sound Bar Wings and sound bar to work with the Visual Heat Sensor.
The Sound Bar Wings may be positioned and rotated so that the Visual Heat Sensor {219} will reach below the sound bar.
For example, if a sound bar is tall, the Brace Extenders {30} and Horizontal Brace can be attached lower down on the Vertical Braces toward the bottom of the sound bar while the Wings point upwards in order to align with the sound bar's installation holes.
{31} {31}
{30} {23}
{23} {18}
{30} {18}
{55}
1.10
Attach Visual Heat Sensor to the Horizontal Brace.
Attach the Visual Heat Sensor {219} with Screws {15} to the Horizontal Brace {55}, Set the height so the Visual Heat Sensor is as visible as desired.
Note: If using the minimum height from chart in Step 2.2, keep the exposed heat sensor pad no more than 1" below the TV or soundbar. When first moving the mount down ensure the visual heat sensor clears the mantel.
1" Max below TV or Soundbar
SIDE VIEW
{53}
TALLER SOUND BAR WIDERWSOIDUEND BAR
{55}
{219}
{15}
Protect the TV with the Visual Heat Sensor. The Visual Heat Sensor turns red if the temperature above the fireplace exceeds a safe 110° F a visual cue that either the TV needs to be raised to the UP position or the fireplace needs to be turned off.
Customer Support 1.800.897.9755 x1 support@mantelmount.com 9
STEP 2
Determine Wall Placement
2.1
Measure the distance from the bottom of the Vertical Braces {31} (not the Extenders) to the bottom of the TV/
sound bar.*
{31}
MEASURE THIS
DISTANCE
2.2
Determine the minimum vertical position of the Wall Plate.
Use the Look-up Table below to find the minimum distance between the mantel and the bottom of the lower Wall Plate {32}. This will be the intersection of the distance from STEP 2.1 and the mantel depth. Write the minimum distance in the box below.
DISTANCE FROM 2.1
DEPTH OF MANTEL
8" OR LESS 9"
3" 3.50
3.75
4" 4.50
4.75
5" 5.50" 5.75
6" 6.50" 6.75
7" 7.50" 7.75
8" 8.50" 8.75
9" 9.50" 9.75
10" 10.50" 10.75
10" 4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00
11" 4.75 5.75 6.75 7.75 8.75 9.75 10.80 11.80
12" 5.50 6.50 7.50 8.50 9.50 10.50 11.50 12.50
13" 6.50 7.50 8.50 9.50 10.50 11.50 12.50 13.50
14" 7.75 8.75 9.75 10.80 11.80 12.80 13.80 14.80
15" 9.25 10.30 11.30 12.30 13.30 14.30 15.30 16.30
16" 11.50 12.50 13.50 14.50 15.50 16.50 17.50 18.50
DISTANCE
*If installing this mount with a MantelMount
RB100 Recess Box, the bottom of the Vertical Brace must be 6"-10" from the bottom of TV (or 6" from the bottom of the Soundbar if one is installed).
10 MM815 Installation Instructions
VALUE FROM LOOK-UP TABLE
MINIMUM DISTANCE BETWEEN MANTEL AND LOWER WALL PLATE HOLES
Most customers want their TV mounted as close to the mantel as possible. If this describes you, go directly to STEP 2.4.
However, if you want the TV higher on the wall (such as centered between the mantel and ceiling) e.g. for extra space on the mantel for pictures or a center speaker, continue to STEP 2.3.
2.3 Determine a higher vertical position of the Wall Plate.
OPTIONAL Some customers want the TV centered between the mantel and the ceiling or crown molding. Others want enough space below the TV for pictures or a center speaker.
The TV's position on the wall is directly related to the placement of the lower Wall Plate. To determine exactly where to place the lower Wall Plate, choose an option below that best describes your scenario and fill in the boxes.
NOTE: Distance "E" below must always be at least the minimum distance in STEP 2.2
Option 1: I want the TV centered between the mantel and ceiling/crown molding.
1. Record measurements already taken:
OR
Option 2: I want the TV a specific distance above the mantel.
1. Record distance from STEP 2.1 (from pg. 8) (C)
Wall Space Height (from pg. 2)
(A)
TV Height (from pg. 2)
(B)
Distance from STEP 2.1 (from pg. 8) (C)
2. Subtract the TV Height (B) from the Wall Space Height (A), then divide by 2.
(A) (B) =
(D)
2
2. Write the specific number of inches
you want between the mantel and
(D)
the TV (or TV with sound bar):
3. Add (C) and (D) to determine how many inches above the mantel to place the lower Wall Plate holes.
(C) + (D) = (E)
3. Add (C) and (D) to determine how many inches above the mantel to place the lower Wall Plate holes.
(C) + (D) =
(E)
Distance between mantel and lower
(E) wall plate holes
2.4
Find the center of your mantel and the centers of two studs.
Measure and mark the center line of the mantel onto the wall with tape.
Next, use a stud finder to locate two studs, one on each side of the centerline. (If you prefer to use one center stud alone, see "Mount Space" in the Troubleshooting Tips on page 22.)
Then, at the height from either Step 2.2 or 2.3, locate the center of the stud(s) by poking a sharp awl or finish nail through the drywall to find each stud edge. Mark these center spots on the wall. Lag Bolts must be installed into the CENTER of the studs in STEP 3.1.
Cutout shown for reference
AWL
2Aan.li5dgn
the arrows on the Wall Plate {32} pointing upward. Center level the plate above the mantle and position the height using the table in STEP 2.2. Mark the 4 spots for lag bolts directly on center of the studs.
Cutout shown for reference
Minimum Height from STEP 2.2
2.6
Pre-drill the 4 holes with 7/32" drill bit to a depth of 2.5 inches (65mm) including wall covering.
Note: Wall covering (drywall) must not exceed 5/8" thickness.
STUD FINDER
CL
Customer Support 1.800.897.9755 x1 support@mantelmount.com 11
2.7
If necessary, move Wall Plates to clear an outlet.
If a Wall Plate installation is impeded by an electrical outlet (or other) and professionally relocating the outlet is impossible, try one of these two options:
Move Wall Plates up or down to clear the outlet. As long as you don't place the LOWER Wall Plate below the Minimum Distance (Step 2.2) or above the Maximum Distance (step 2.3), MantelMount will still function properly.
BEFORE Wall plate impeded by outlet.
After Wall Plate lowered to clear outlet.
Simply move the Wall Plates up or down enough to clear the outlet, leaving them as close as possible to the originally planned vertical positions.
IMPORTANT: You must now move the Vertical Braces {31} on the back of the TV using the same number of inches used to move the Wall Plates (e.g., move the Vertical Braces down 2" if the Wall Plates were moved down by 2" ). The bottom of the Vertical Braces must remain between 3 to 10 inches from the bottom of the TV.
OPTIONAL: If you prefer to drill an access hole in your wall plate cover, the outlet may be placed within the footprint of the wall plate.
NOTE: If outlet is directly behind the Lifting Arm, the only solution is to move the Wall Plates up.
BEFORE
If the wall plate sits directly behind lifting arm wall plate must be moved up.
After Wall plate moved up to clear outlet.
Move the Wall Plates up enough to clear the outlet, leaving them as close as possible to the originally planned vertical positions. IMPORTANT: You must now move the Vertical Braces {31} on the back of the TV using the same number of inches used to move the Wall Plates (e.g., move the Vertical Braces up 2" if the Wall Plates were moved up by 2" ). The bottom of the Vertical Braces must remain between 3 to 10 inches from the bottom of the TV.
12 MM815 Installation Instructions
STEP 3
Attach Mount to Wall
3.1 Attach the Wall Plate {32} with arrows up, using Lag Bolts {17} and Washers {11} directly into the centers of the studs With a 13mm wrench.
: Do Not overtighten Lag Bolts {17}. Tighten only until the washers are firmly against the wall plate. Damage due to overtightening can cause property damage or injury.
3.2 Insert bottom tabs of Lifting Mechanism {35} into the slots of Wall Plate {32} then slide the top into position. Align all four holes and install Screws {14}. Tighten Securely.
Note: Do NOT let go of Lifting Mechanism {35} until Screws {14} are installed.
2 1
3.3 Power up the mount. Plug Power Supply into mount then into wall socket. The TV remote should work out of the box. Move Mount Down 2 Inches by holding .
If TV remote does not work it needs to be paired.
To Pair Remote: 1. Unplug Power to mount for 30 seconds 2. Hold the (DOWN) button while plugging in power 3. Keep holding (DOWN) button for around 10 seconds
until mount moves down
3.4
Run System Reset System reset ensures software is running correctly. Press Set. Press Run. Press/Hold Set. Mount will move to the top position. Keep holding for 5 seconds after mount reaches top position.
Press and hold DOWN button for 10 seconds.
Press
Press
Press and hold.
Customer Support 1.800.897.9755 x1 support@mantelmount.com 13
3.5
Programming Bottom Stop
Warning: Damage will occur If the Mount can drive down into something, the bottom stop needs to be set.
If the mount would hit the Mantel or some other object in the bottom position. You can easily reduce the bottom most ( ) position so that the mount cannot move past that point.
1. Drive mount to the desired Bottom-most Position by holding
2. Do NOT allow the mount to run into anything
3. Press Set
4. Press
5. Press/Hold Set for 4 to 8 Seconds
6. Check it was correctly done by trying to move the mount down farther
Note: To delete the bottom stop follow steps 3 to 6 but hold the set button for more than 10 seconds in step 5.
3.6
Swivel Safety Clutch
The Swivel on the mount has a friction clutch that automatically disengages to avoid damage if the mount swivels into something, or someone swivels the mount manually. If that happens the swivel will be out of position and the swivel will not work as expected. The swivel needs to be recalibrated right away to avoid damage.
To recalibrate Auto-move the mount to the top position:
Press Run Press within 3 seconds
The mount will automatically move to the top position and recalibrate. You can also run Reset Function to recalibrate.
3.7
Attach the TV Brace {33} to the lifting arm {35}. Manually Swiveling the Swivel Plate will make accessing the screw holes easier. Level the TV Brace and tighten the 4 screws {15}.
NOTE: After TV is mounted to bracket you may need to adjust these screws to make final Post-Leveling adjustments (Step 5.6).
Press
Press within 3 Seconds
Note: If clutch is engaged the mount may swivel a little when coming down, to fix this; manually center mount at zero degree swivel by rotating TV with hands and over-riding clutch. Mount is at zero degrees swivel after you recalibrate (drive the mount to the top position), then move the mount straight down.
14 MM815 Installation Instructions
STEP 4
Attach TV to Mount
NOTE: These Next Steps Will Require Two People
4.1
WARNING!
Do Not put hands into Lifting Mechanism. The power of the Lifting Mechanism can cause bodily injury!
Pinching and Crushing Hazard.
The wall mount actuation is very strong, do NOT run the mount when anyone is near the mount. Do NOT have any part of the body in the mount or between the TV and Wall. The Mount will keep driving until someone pushes another button on the remote to stop it. When working on the mount unplug the power.
Never allow small children to play around or operate the MantelMount. Property damage or personal injury can occur.
4.2
This step requires two people.
Carefully hang the Television onto the TV Brace making sure that both hooks on the Vertical Braces {31} engage the TV Brace {33}.
Customer Support 1.800.897.9755 x1 support@mantelmount.com 15
4.3
Center the TV on the TV Frame and check it with a level.
Carefully slide the TV sideways, if required, until it is balanced and horizontal, up to a MAXIMUM OF 2 INCHES left or right.
The TV would only need to be moved off-center if it has an unbalanced weight. These are usually older, heavier TVs.
If the TV needs to be moved sideways and is visually too much off-center above the mantel, remove the TV and relocate the Wall Plate {32} an equal distance but in the opposite direction of the TV to compensate.
4.4 Install 4 Screws {15} through the TV Brace {33} and into the Vertical Braces {31}.
4.5
Attach cable ties to lower arm.
Shown below is the easiest way to attach cables. Use the included Cable Ties {24} to attach cables so they attach to the underside of the Lower Arm, making a gentle loop.
Cables should be long enough to accommodate the extension and swivel of MantelMount. Check all ranges of motion before tightening the Cable Ties.
4.6
Attach the electrical and signal cables to the TV.
Run signal cables through open loop. Give each segment of the cables extra length so that they are not stressed or kinked when the mount moves.
Ensure that cables do not get pinched within the Lifting Arm when the TV is raised.
Reference Only: This is one possible configuration for the signal cables. Each segment of the cables has extra length so that the cables are not stressed or kinked when the mount is moved.
16 MM815 Installation Instructions
STEP 5
Make Final Adjustments
Centering Cam Swivel Hardstop
Top Tilt Adjust
Post-Leveling
Bottom Tilt Adjust
5.1
Programming Left/Right Stop
If the mount would swivel into the Mantel or some other object in the bottom position. You can easily reduce the right and left swivel limits so that the mount cannot move past them.
1. Press Run then to calibrate (Mount Should move all of the way to the Top Position).
2. Drive mount to the Bottom Position
3. Press and hold or to swivel
mount as far as wanted
4. Press Set.
5. Press or .
6. Press/Hold Set for 4 to 8 Seconds.
7. Check it was correctly done by trying to move the mount past set swivel.
Note: To delete the swivel soft stop follow steps 3 to 6 but hold the set button for more than 10 seconds in step 6
5.2
Adjust the Side Swivel Stop positions, if necessary.
To keep the TV from bumping the mantel or wall, loosen the Locknuts {23} and adjust the Swivel Stop Screws to the desired stopping left and right positions. Tighten both Locknuts after the adjustments are made. Mechanical Swivel Stops should be just past the programmed swivel stop
If a small amount or no swivel is desired, it may be necessary to remove the Screw and/or Locknuts and reattach them on the other side of the Swivel Bracket.
NOTE: To better access swivel stop adjustments screws swivel the mount to the left or right to gain better access.
Customer Support 1.800.897.9755 x1 support@mantelmount.com 17
5.3
Centering Cam Adjustment.
The Centering Cam automatically swivels the TV to center while raising to avoid permanent obstacles.
Out of the Box they are set for max protection, to get more possible swivel follow below steps.
Warning: ensure Cams are set to avoid damage.
Steps to Set Cam: 1. Move TV to Out Position. 2. Swivel TV so that it is near the wall or mantel. 3. Swing Centering Cam forward until Cam Rollers
Contact. 4. Tighten Cam Nut. 5. Repeat on other side. 6. Swivel the TV and Hold the UP button to ensure it is
set so that the TV can swivel as much as possible in either direction without it hitting.
5.4
Bottom and Out Tilt Adjustment.
To adjust the tilt in all positions besides the Top Position. 1. Adjust Tilt Adjustment Screw with a 10mm Wrench.
· Tighten (Clockwise) to tilt TV up · Loosen (Counterclockwise) to tilt TV down
A B C A.) Cam Nut B.) Centering Cam C.) Cam Contact Rollers
5.5
Top Position Tilt Fine Adjustment
TV Tilt in the Top Position can be fine tuned:
1. Drive the Mount to the Topmost Position to check Tilt 2. Drive the Mount down to Access Adjustment Screws 3. Adjustments must be done the same on each side of
the mount 4. Loosen the Lock Nuts 5. Adjust Tilt Adjustment Screws 6. Tighten (Clockwise) to tilt TV down 7. Loosen (Counterclockwise) to tilt TV up 8. Check the settings are the same on both sides 9. Drive Mount to Topmost Position to check Tilt 10. Repeat steps 2-9 until satisfied 11. Tighten Lock Nuts
Bottom and Out Tilt Adjustment Screw
Tighten screw for more UP tilt.
5.6
Make Post-Leveling adjustments, if necessary.
Place a level on top of the TV while it's in the UP position. If it's level, the installation is complete! If not, slightly loosen all four Leveling Screws {15} and rotate the TV until it's level and then tighten all the Screws.
{15} x4
18 MM815 Installation Instructions
Top Tilt Adjustment Screw
Locknut
Loosen Screw for More Up Tilt
5.7
Set Memory Position
To Set Positions 1, 2. There are 2 settable Positions which can be set.
1. Drive the mount to the desired Position.
2. Press Set
3. Press the Memory (Button 1 or 2) Button within 3 seconds
Quick Note:
To return mount to the home position press: Run then arrow.
This will Auto-Swivel and move mount to the topmost position.
5.8 Paint the Wall Covers {29} if desired.
5.9 Attach the eight Wall Cover Clips to the wall frame as shown below. These will be used to attach the adhesive Velcro strips that hold the wall covers to the wall frame.
5.10 Install the Wall Covers using the included adhesive Velcro strips. Attach the Hook {25} and Loop {26} strips together onto the Wall Cover Clips, and then press the Wall Covers into the correct position onto the Wall Plate. This will properly align the velcro onto the Wall Covers.
Hook and Loop Together
Customer Support 1.800.897.9755 x1 support@mantelmount.com 19
20 MM815 Installation Instructions
31 18 52
23 16
253
23
85
261
206 80
216
33
255
15 255
209
202
87
80 57
15
31
15 18 23 10
82
267
205
55
82
252 212
260
15
213
222
204
208
252
253
217
215 256 85 257
268 14
23 23 11 81
85
86 226 220
214
211
228
60
218 88
231
89
219
221
30
49
262
265
227
85
210
264
273 261
207
269
224
230 259
229 272
223
261
203
85
81
84
82
11
14
201 271 266
270 63
14 32
Customer Support 1.800.897.9755 x1 support@mantelmount.com 21
ITEM #
1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 20 23 24 25 26 30 31 32 33 49 52 55 57 60 80 81 82 84 85 86 87 88 89 63 219 201 202 203 204
PART #
12189 12190 12191 12195 12194 12193 12197 12198 12199 12166 14126 12122 12176 12178 15083 12154 12255 MM815 Manual 12183 12162 12139 12141 14056 14038 13011 24030 12222 15010 14060 12113 24127 12115 12174 12185 13064 21191 24142 24153 12187 14128 25000 24219 24201 24202 24203 24204
DESCRIPTION
M5 x 12 M5 x 30 M5 x 40 M6 x 16 M6 x 30 M6 x 40 M8 x 15 M8 x 25 M8 x 45 Washer M6 Washer M8 x 2 Spacer BHCS M8x16 Round Head Screw M6 x 12 CARRIAGE BOLT M6 X 12 Lag Bolt M8 x 60 Round Head Screw M6 x 40 MM815 Instruction Manual Locknut M6 Cable Tie Velcro Strip Hook Velcro Strip Loop Brace Extender TV Vertical Brace Wall Frame TV Frame Handle Rubber, Temp Change Sound Bar Wing TV Horizontal Brace Wall Cover TP7 Plug Bushing M6x10 SHCS Nut M6 Shaft 164 Locknut M5 M10 External Retain Ring Cable Tie Mount Locknut M8 M10 Washer Wall Cover Clip MM815 Temp Display MM815 Wall Bracket MM815 Upper Arm MM815 Lower Arm MM815 Swivel Plate
QTY.
4 4 4 4 4 4 4 4 4 8 12 12 8 12 4 4 4 1 13 16 8 8 2 2 1 1 2 2 1 2 1 4 4 5 1 11 3 1 1 2 8 1 1 1 1 1
ITEM # 205 206 207 208 209 210 211 212 213 214 215 216 217 218 220 221 222 223 224 226 227 228 229 230 231 232 252 253 255 256 257 259 260 261 262 264 265 266 267 268 269 270 271 272 273
PART # 24205 24206 24207 24208 24209 24210 24211 24212 24213 24214 24215 24216 24217 24218 24220 24221 24222 24223 24224 24226 24227 24228 24229 24230 24231 24232 24252 24253 24255 24256 24257 24259 24260 24261 24262 24264 24265 24266 24267 24268 24269 24270 24271 24272 24273
DESCRIPTION MM815 Swivel TV Plate MM815 Centering Cam MM815 Bottom Tilt Adjust MM815 Motor Coupling MM815 Clutch Preload MM815 M6 Bushing MM815 Motor Attach MM815 Motor Spacer MM815 Swivel Spacer MM815 Controller Holder MM815 Centering Roller MM815 TV Side Shaft MM815 TV Shaft Spacer MM815 Actuator Adjust MM815 TA16 Actuator MM815 Swivel Motor MM815 Custom M8 HHCS MM815 Bot Tilt Spacer Short MM815 Bot Tilt Spacer Long MM815 Actuator Pin TV Side MM815 TFH22 RF Remote MM815 TC7 Controller MM815 Actuator Adjust Pin MM815 Bot Tilt Spacer Med MM815 Actuator Adjust Spacer MM815 Swivel Wire M5x8 Set Screw, McM 91390A117 M6x12 Shoulder Bolt, McM 92981A101 M6x22 BHCS M4 ID 22 OD, McM 91100A130 M4 Rubber Washer, McM 90133A017 M6x60 Shoulder Bolt, McM 92981A109 M3x8 SHCS M6 15OD Belleville, McM 96445K294 M5x45 SHCS M6x20 Shoulder Bolt, McM 92981A103 M6x15 Shoulder Bolt, McM 92981A751 M6x100 SHCS Fully Threaded M6x30 BHCS M3x35 SHCS M2.5x16 Cotter Pin, McM 98350A621 M10x110 Full Thread SHCS M10x40 SHCS M10 Nut, McM 90592A024 M6 Washer 30 OD 1 Thick
QTY. 1 2 1 1 1 3 1 4 2 1 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 4 2 2 1 4 4 4 1 1 1 2 2 1 1 1 3 1
TROUBLESHOOTING TIPS
Customer satisfaction is our top priority!
Following are solutions for the most common installation challenges. For further assistance, visit www.mantelmount.com/troubleshooting or contact Customer Support at 1-800-897-9755 ext.1 or support@mantelmount.com, Monday through Friday, 7am to 4pm PST.
NOTE: In rare cases, one troubleshooting adjustment may create the need for another. Be prepared for some trial and error.
MOUNT SPACE
ISSUE The wall covering is made of brick or stone.
The drywall/stucco wall covering is thicker than 5/8".
SOLUTION It's possible to install MantelMount by using concrete anchors (included) with the Lag Bolts {17}, PROVIDED the brick/stone/wall is structurally sound, several inches thick, and can handle four times the weight of the TV and mount. Working with a concrete/masonry professional for this type of installation is recommended.
Please contact Customer Support for guidance before attempting installation.
A single wood stud is centered on my wall.
MantelMount recommends adding more support so mount can attach to the equivalent of 2 studs.
MOUNT PERFORMANCE
ISSUE
SOLUTION (May require some trial and error to reach optimal performance.)
Swivel is off
Swivel needs to be recalibrated 1. Press Run 2. Press Within 3 seconds to allow Mount to move all of the way to the top position. Mount should be recalibrated. You can also run Reset Function to recalibrate. See page 5.
NOTE: The Swivel on the mount has a friction clutch that automatically disengages to avoid damage if the mount swivels into something, or someone swivels the mount manually. If that happens the swivel will be out of position and the swivel will not work as expected. The swivel needs to be recalibrated right away to avoid damage. To recalibrate Auto-move the mount to the top position:
TV isn't vertical in out and bottom positions
See step 5.4 to adjust the Bottom/Out Position tilt
TV isn't vertical in the Top Position
TV is not returning to same memory position
See step 5.5 to adjust the Top Position tilt
1. Press Run 2. Press within 3 seconds 3. Allow Mount to move all of the way to the top position and wait 5 seconds 4. Mount should be recalibrated 5. Or run System reset, See page 5.
Mount does not move
There are a few things to try 1. Run System Reset, see page 5 2. Check that power is getting to the mount by making sure there is a green light shining on the plug. 3. Replace the CR2032 battery in the remote. 4. Check that the wires in the mount are plugged in and not damaged. 5. Pair the RF remoted, see Step 3.3 6. Maybe the Bottom Limit got set too high, clear the Bottom Travel Limit, see Page 5. Warning: The mount can now travel all of the way down and the Bottom Limit will have to be redone, see section 3.5.
22 MM815 Installation Instructions
CONTINUED ON NEXT PAGE
TROUBLESHOOTING TIPS
CONTINUED FROM PREVIOUS PAGE
MOUNT PERFORMANCE
ISSUE
SOLUTION (May require some trial and error to reach optimal performance.)
Mount is acting weird
Run System Reset, see Page 5
Mount swivels a little when coming down
TV LEVELING
ISSUE TV is not level in the UP and/or DOWN positions.
TV is level in the UP position, but unleveled in the DOWN position, or vice cersa.
Manually center mount at zero degree swivel by rotating TV with hands and over-riding clutch. Mount is at zero degrees swivel after you recalibrate (drive the mount to the top position), then move the mount straight down.
POSSIBLE CAUSE The mantel, ceiling or floor may not be level.
Vertical Braces aren't evenly attached.to the back of the TV.
Wall Plates aren't level.
The Top Stops aren't evenly set. TV is heavier on one side.
HOW TO CHECK Compare TV level with that of the mantel and floor.
Look at the back of the TV and ensure that the top of the Vertical Braces are offset from the top of the TV the same distance.
Use a level on top of Wall Plates to verify that it's not level.
SOLUTION
1. Adjust until visibly satisfactory. 2. Move the TV down. 3. Make Post Leveling adjustments (Step 5.6) and
match the level readings of the mantel with the TV. 4. Ensure Top Tilt Adjustment is the same on each side of the mount, see Step 5.5
1. Remove electrical and signal cables (Step 4.5). 2. Detach the TV Brace from the Vertical Braces
(Step 4.4). 3. Remove the TV from the TV Brace (Step 4.2) and lay
TV face down on a blanketed surface (Step 1.1). 4. Remove the Vertical Brace(s) as necessary. 5. Reposition the Vertical Braces so that they are
properly parallel to one another, then repeat Step 1, Step 4 and if necessary, Step 5.
1. Remove electrical and signal cables (Step 4.5). 2. Detach TV Brace from Vertical Braces (Step 4.4). 3. Remove the TV from the TV Brace (Step 4.2) and
lay TV face down on a blanketed surface (Step 1.1). 4. Slightly loosen all four Lag Bolts (Step 3.1). 5. Adjust Wall Plates so that they are level. 6. Hold Wall Plates in level position and firmly tighten
the four Lag Bolts. Heed warning in Step 3.1. 7. Once the Wall Plates are level, repeat Steps 3, 4 and 5.
Use a level to verify the TV is level in the UP position but not in the DOWN position, or vice versa.
Follow the instructions in Step 5.5. Be prepared for some trial and error. If adjusting the Top Stops doesn't solve the problem, try the solution below for when a TV is heavier on one side.
Use a level to verify the TV is level in the UP position but not in the DOWN position, or vice versa.
Attach a counterweight to the back of the TV. Contact Customer Support for assistance.
Customer Support 1.800.897.9755 x1 support@mantelmount.com 23
For missing/damaged parts or questions during installation, please contact our Customer Support team at 1.800.897.9755 ext.1 or support@mantelmount.com. Customer satisfaction is our highest priority!
MAILING ADDRESS: 2647 Gateway Road Ste. 105-435 Carlsbad, CA 92009 mantelmount.com
U.S. Pat. No. 8,864,092 , No. 8,724,037 - For more information on MantelMount patented technology visit: www.mantelmount.com/pages/patents
© 2022 MANEHU PRODUCT ALLIANCE, LLC
REV. 09.30.22
Adobe PDF Library 16.0.7 Adobe InDesign 17.4 (Windows)