MM-Max1 Pull Down TV Mount Installation Instructions

Important Safety Information

Read this entire manual before you begin! Contains important safety information ? - please save this manual.

WARNING! Do not place hands into Lifting mechanism. The force of the Lifting mechanism can cause bodily injury!

WARNING! This product contains small parts that can be a choking hazard. Do not let children play with any of these small parts! Keep children away from the work area during the installation process.

CAUTION: This product is intended to be installed by professional installation contractors, or persons familiar with the tools and methods required for this installation. If you are not sure about your ability to perform this installation, you must contact a professional. MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.

Do not let children operate, pull on, or hang from MantelMount. Do not let children push MantelMount upward to the top position. Only a person tall enough to control the mount all the way to the top should operate MantelMount.

Do not use this product in any way, or for any purpose, that is not specifically described in these instructions. MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.

Installation Steps Overview

The installation process is divided into five main steps:

• Step 1 - Attaching Braces to TV
• Step 2 - Determine Wall Placement
• Step 3 - Attach Mount to Wall
• Step 4 - Attach TV to Mount
• Step 5 - Make Final Adjustments

Contact Customer Support

For any questions during installation, Contact Customer Support: Monday - Friday, 7am - 4pm PST at 1.800.897.9755 x1 or support@mantelmount.com.

Helpful Installation Tips and Videos can be found at: http://mantelmount.com/install-tips

Warranty Information

MantelMount offers a Lifetime Limited Warranty for all TV mounts and accessories. This Lifetime Limited Warranty covers all mechanical parts but excludes lifetime coverage for gas springs or electrical parts which are warrantied for five (5) years from the original purchase date.

This product is intended to be installed by professional contractors or persons familiar with the tools and methods required for this installation. If you are uncertain about your ability to perform this installation, please contact a professional.

Do not use this product in any way or for any purpose that is not specifically described in these instructions.

Product Dimensions and Features

The MM-Max1 mount offers a maximum drop of 29 inches and a thickness of 3.25 inches.

Dimensions for TV to Vertical Brace attachment are critical: Measure TV to Vertical Brace {31}. The distance of the Vertical Brace {31} above the Wall Frame {40} should be 11 inches, and below the Wall Frame {40} should be 2 inches.

The Wall Frame {40} can be positioned up to 40 inches from the TV, with a maximum clearance of 22 inches for full motion (40° L-R).

Exclusive MantelMount Features:

• Independent horizontal, swivel, and vertical movements.
• Adjustable lifting force keeps the TV neutral in all positions.
• Multiple Viewing Angles: Extends from the wall and lowers to eye level for optimal viewing. Make any seat the best seat in the house.
• Visual Temperature Sensor: Handle changes to red color at temperatures above 110 °F to warn users if the fireplace is too hot for TV safety.

© 2024 MANEHU PRODUCT ALLIANCE, LLC. For more information on MantelMount patented technology visit: www.mantelmount.com/pages/patents

Before Installation

1. Verify TV and Wall Space Meet Criteria

Screen Size:

• 50" to 86" (With Soundbar)
• 55" to 86" (Without Soundbar)

Weight Capacity:

• 20 to 90 LBS. (Including Sound Bar)

VESA COMPLIANT: Up to 600 X 600mm

Mantel Depth: 20" MAXIMUM

Stud Requirements: Wood studs for mounting. Studs Maximum 28" apart; Wall Covering Maximum 5/8".

2. Verify Space Height

The height of your space must be at least 4 inches taller than the largest height of your TV, or your TV / Soundbar combination. This is calculated as: (Distance from Top of TV to Bottom of TV or Soundbar) + 4 Inches. A 2-inch minimum clearance is required at the top and bottom of the TV/Soundbar.

3. Verify Required Tools

• Stud Finder
• Pencil
• Level
• AWL
• Allen Wrenches
• Socket Wrench
• Phillips Wrench
• Drill Bit (7/32")
• Power Drill
• Tape Measure
• Tape Dispenser

4. Verify All Parts Are Included

Check the included parts against the list provided in the manual. If any parts are missing or damaged, contact Customer Support at 1-800-897-9755 x1 before installing.

STEP 1: Attach Braces to TV

1.1 Do You Need the VESA Extenders?

If your TV's VESA holes align with the main holes on the VESA Extenders {62}, do not use the extenders. If they do not align, attach the VESA Extenders {62} to your TV using the appropriate silver TV screws.

1.2 Test-Fit the TV Components

The bottom of the Vertical Braces {31} must be attached within 3"-12" from the bottom of the TV or soundbar. Confirm that the Braces will attach to the TV at this distance. For a clean look, place Brace Extenders {30} slightly above the bottom of the TV. Ensure the Center Heat Sensing Handle {42} can be grabbed at the bottom of the TV or soundbar.

1.3 Determine TV Back Type

Check if the back of your TV is flat or irregular. The TV Components must be parallel with the TV screen. Use Spacers {12} as shown if needed for recessed threads or irregular backs.

1.4 Select Screws and Spacers

Select the appropriate screw and spacer combination for your TV's threaded inserts. Ensure adequate thread engagement without bottoming out the screw. Use the provided diagrams to choose the correct screws {4-9} and spacers {12}.

CAUTION: Do not use screws that are too long for the TV's threaded inserts because it may damage internal components!

1.5 Hand-thread Screw Combination

Hand-thread the selected screw combination into the TV's threaded inserts. Ensure there is adequate thread engagement without hitting the bottom of the threaded insert.

1.6 Attach the Vertical Braces

Attach the Vertical Braces {31} to the TV. Mount them as low as possible on the TV, ensuring the bottom of the braces is within 3"-12" of the bottom of the TV (or Soundbar). Lower mounting hides more of the mount.

1.7 Attach Horizontal Brace and Brace Extenders

Slide the Brace Extenders {30} onto each side of the Horizontal Brace {43}, centering the brace. Use the Vertical Braces {31} on the TV as a temporary guide to attach the Extenders to the Horizontal Brace using Screws {15}. Attach the Extenders to the Vertical Braces with Screws {18} on the INSIDES and Nuts {23} on the OUTSIDES. Do not install the Center Heat Sensing Handle {42} until Step 5.3.

1.8 Optional: Soundbar Configurations

The soundbar can typically be attached directly to the Horizontal Brace {43}. Soundbar Wings {16} are provided for situations where the soundbar's mounting holes are too wide for the Horizontal Brace or too tall for the Handle to reach below. Otherwise, do not use the wings.

Step 2: Determine Wall Placement

2.1 Determine Wall Location

Measure the distance from the bottom of the Vertical Braces {31} on your TV to the bottom of your TV (or the bottom of the Soundbar if used). This distance should be between 3"-12". Add 4 inches to this measurement. The bottom of the Wall Frame {40} will be installed at least 4 inches higher than this calculated distance.

2.2 Find Center of Mantel and Studs

Measure and mark the center line of your mantel onto the wall with tape. Use a stud finder to locate two studs, one on each side of the centerline (maximum stud width is 28 inches). At the height determined in Step 2.1, locate the center of the studs by poking a sharp awl or finish nail through the drywall to find each stud edge. Mark these center spots. Lag Bolts {17} must be installed into the center of the studs.

2.3 Mark Wall Location with Template

Use the calculated height from Step 2.1 to position the template on the wall. Level the template and tape it into place. Mark at least four holes where the template slots align with your wall studs. Do not locate holes higher than necessary unless you have verified sufficient top clearance.

2.4 Pre-drill Holes

Pre-drill the 4 marked holes using a 7/32" drill bit to a depth of 2.5 inches (65mm), accounting for wall covering thickness. Wall covering must not exceed 5/8" thickness.

2.5 Concrete Wall Installation

For concrete walls, ensure the blocks or solid walls can support four times the weight of the TV and Mount. Install anchors at least 2 inches from mortar or joints.

2.6 Installing Concrete Anchors

Drill pilot holes to a depth of 3 inches (75mm) using a 3/8" (10mm) diameter masonry drill bit. Insert Concrete Anchors {57} until flush. Pilot holes must be at least 2 inches away from any mortar joint.

Step 3: Attach Mount to Wall

3.1 Attach The Wall Frame

Level the Wall Frame {40} and attach it to the wall using Lag Bolts {17} and Washers {11}. Do not over-tighten Lag Bolts {17}. Tighten only until the washers are firmly against the wall plate. Over-tightening can cause property damage or injury.

3.2 Attach The Wall Frame Covers

Tuck the center tabs of the Wall Frame Covers {41} under each other before snapping the cover onto the metal post inside the Wall Frame. To remove, gently pry the cover from the end.

3.3 Prepare The Lifting Mechanism

Partially thread four Screws {13} into the threaded tabs on the sides of the Lifting Mechanism {55}. Do not thread them all the way in; leave a 1/4" gap for hanging.

3.4 Hang the Mechanism

Pull the Wall Frame {40} horizontally from the wall. Lower the thread gaps of the top screws of the Lifting Mechanism {55} into the top slots of the Wall Frame, then swing the lower screws into the lower slots. Do not tighten these screws yet.

3.5 Remove Tilt of the Lifting Mechanism

Install two Screws {15} into the threaded holes at the back of the Wall Frame bracket. Using a level vertically on the front of the Lifting Mechanism, remove any unwanted tilting by turning these screws in or out. Ensure both screws are equally snug against the Lifting Mechanism.

3.6 Secure the Lifting Mechanism

Tighten the four Screws {13}. Be prepared to loosen these screws and re-adjust the tilting screws (Step 3.5) after hanging the TV, as the TV's weight may add unwanted tilting.

STEP 4: Attach TV to Mount

4.1 Pre-adjust the Lifting Force

Before hanging the TV, determine your TV's weight from its manual or website. Adjust the tension bolt on the Lifting Mechanism {55} so the front edge of the Gas Spring Block aligns with the correct weight setting. Rotating the bolt clockwise (labeled "MORE") increases lifting force.

4.2 Hang the TV

This step requires two people. Pull the Lifting Mechanism {55} away from the wall. Hang all four hooks of the TV braces onto the mechanism and slowly release the TV. If the TV starts to lower, remove it and increase the lifting force as described in Step 4.1.

4.3 SECURE the TV

Insert four Screws {15} into the Vertical TV Braces {31}. Do not tighten them until the TV is leveled in Step 5.1.

STEP 5: Make Final Adjustments

5.1 Level the TV

If the TV is not level, insert the Leveling Block {56} with Screw {13} into the notch in the Vertical TV Brace {31} on the side that is too low. Turn the Screw downward until the TV is level.

5.2 Tighten the Hanging Screws

Once the TV is level, tighten the four Screws {15} securing the TV to the mount.

5.3 Install the Center Heat Sensing Handle

Attach the Center Heat Sensing Handle {42} with Screws {15} to the Horizontal Brace {43}.

5.4 Fine Tuning the Lifting Force

From the back of the Lifting Mechanism {55}, adjust the lifting force using the tension bolt (as in Step 4.1) until the force required to raise and lower the TV is equal in both directions.

5.5-5.8 Routing Component Cables

Pull the mount all the way down. Route component cables as shown in the diagrams. Cables should be attached to the cable anchor {22} on the Vertical Brace {31}. Ensure cables have a reverse loop behind the hanging bracket. In the UP position, the cable should have a slight dangle. Run the cable along the outside of the first horizontal arm and attach with a small cable clip {60}, then on the inside of the second horizontal arm and attach with a large cable clip {61}. In the UP position and flat to the wall, the cable on the horizontal arms should be visible and should not pinch or bind through all motions.

Parts List

The following is a comprehensive list of parts included with the MM-Max1 mount. Contact Customer Support if any parts are missing or damaged.

Additional Information

For missing/damaged parts or questions during installation, please contact MantelMount Customer Support at 1.800.897.9755 ext.1 or support@mantelmount.com. Customer satisfaction is their highest priority.

For more information on MantelMount patented technology visit: www.mantelmount.com/pages/patents

WARNING: This product can expose you to chemicals including Lithium Grease, which is known to the State of California to cause cancer or developmental harm. For more information go to www.P65Warnings.ca.gov.

MAILING ADDRESS: 2647 Gateway Road Ste. 105-435 Carlsbad, CA 92009

Website: mantelmount.com

© 2024 MANEHU PRODUCT ALLIANCE, LLC