Proscenic COCO Smart 790T User Manual

Your Robot

Top View

The top view of the robot includes: Touch Buttons, Display Screen, Dustbin Lid, Bumper, and Power Switch.

Bottom View

The bottom view of the robot includes: Lower Cover, Right Wheel, Charging Socket, Right Brush, Suction Attachment, Brush Attachment, Left Wheel, Battery Compartment Cover, Left Brush, Caster Wheel, and Charging Interface.

Accessories

Remote Control

The remote control allows you to set cleaning plans, navigate with arrow keys, select area cleaning, set time, and control charging functions (ON/OFF). It requires two AAA batteries (not included). Remove batteries if the remote will not be used for an extended period.

Charging Station

The charging station has a Power Interface for connecting the power adapter and Charging Interfaces that connect to the robot. It also features a Power Indicator light.

Setting Up Your Robot

Step 1: Activate Robot

1. Place the charging station in a clear area against a wall on a flat floor.
2. Connect one end of the power cable to the charging station and the other end to a power outlet.
3. Place the robot on the charging station, ensuring the station's charging contacts align with the robot's.
4. Turn the main power switch on the robot (located on the right side) to the "ON" position.

Step 2: The Cleaning Cycle

1. Press and hold the POWER button for 3 seconds to turn on the robot.
2. To start a cleaning cycle, press the POWER button or the CLEAN button again.
3. The robot will clean an entire floor in your home during a cleaning cycle.
4. If the battery is low during a cleaning cycle, the robot will return to the charging station to recharge.

Step 3: Download the Proscenic Robotic App

The Proscenic Robotic App allows you to control your robot vacuum using your iOS or Android device. Search for "Proscenic Robotic" in the Apple App Store (iOS) or Google Play Store (Android) and install it. Open the app and register an account. Follow the app's instructions to connect your robot to your Wi-Fi network (2.4GHz). Press and hold the Charging button until "CONN" appears on the robot's display to connect to the robot.

Controls and LED Indicators

Buttons

• POWER Button: Switches from standby to cleaning mode (press and hold for 3 seconds). Starts cleaning (press once in cleaning mode). Saves time in schedule settings.
• EDGE CLEAN Button: Starts edge cleaning mode along walls.
• CHARGING Button: Returns the robot to the charging station. Increases hours/minutes in schedule settings.
• CLEAN Button: Starts cleaning. Decreases hours/minutes in schedule settings.
• SCHEDULING Button: Accesses or exits time settings. Press and hold to access or exit schedule settings.

LED Indicator (Display Screen)

The display screen shows Time, Charging Status, and Error Codes. Indicator lights show Charging, Cleaning, Scheduling, and Edge Clean status.

Charging the Battery

The robot's battery can be charged directly on the robot or via the charging station. When the battery is low or after cleaning, the robot automatically returns to the charging station. The display shows "1111" upon successful docking and charging initiation. The "CHARGING" button on the robot or remote can also send the robot to the charging station. A voice prompt "Please charge" sounds at low battery. The display shows "FULL" when charging is complete. For optimal battery life, charge for 12 hours before first use or after long periods of inactivity. Charge promptly when the battery is low. For long-term storage, fully charge the battery and turn off the robot using the main power switch.

Creating a Cleaning Schedule

A cleaning schedule allows the robot to start cleaning automatically at set times and days (via the app). First, set the robot's internal clock. To set the clock: Turn the robot on to "Cleaning Mode". Press the "Scheduling Button" to open time settings; the current time will flash. Use the "CHARGING/CLEAN" buttons to adjust hours and the "POWER" button to switch to minutes. Adjust minutes similarly. Press the "POWER" button again to save the time and then the "Scheduling Button" to exit.

To set a cleaning schedule: Ensure the robot is on or charging. Press and hold the "CLOCK" button until numbers flash, then use arrow keys to set the current time and "CLOCK" again to save. Press and hold the "Scheduling Button" for 3 seconds in "Cleaning Mode" to access schedule settings. Set the cleaning time using the "CHARGING/CLEAN" buttons (or arrow keys on the remote) for hours and minutes, and the "POWER" button (or ON/OFF on remote) to save. Place the robot on the charging station to ensure connection. Press the "Scheduling Button" to exit the schedule menu.

Note: To delete a schedule, set the cleaning schedule time to 00:00. The Proscenic app offers advanced features like setting schedules for specific weekdays.

How the Robot Cleans Your Home

Pressing the CLEAN button starts the Auto-Clean mode, where the robot follows a specific cleaning pattern. The robot also offers Area-Clean modes, selectable via the "AREA" button on the remote. You can choose from four different area cleaning patterns: 1x1m square, 2x2m square, 3x3m square, or 4x4m square. After completing a cleaning program, the robot returns to its starting point or the charging station.

Cleaning the Robot

Cleaning the Side Brushes

1. Check if the side brushes are damaged or dirty.
2. Clean the side brushes of dirt using the cleaning accessory or a damp cloth.
3. If a side brush is deformed, remove it and place it in warm water for 5 seconds.
4. Replace the side brush if it is damaged beyond use.

Cleaning the Dustbin and Filters

Empty the dustbin after each use. Follow these steps: 1. Open the lid and remove the dustbin. 2. Remove the HEPA and primary filters. 3. Empty the dustbin.

The dustbin should be rinsed after emptying. The filters can be cleaned with the provided brush or rinsed. Rinse the filters every 15-30 days and ensure they are completely dry before re-inserting. Filters are replaceable accessories and should be changed approximately every 24 months. Do not dry filters in direct sunlight.

Cleaning the Brush Attachment

1. Remove the brush attachment from the bottom of the robot.
2. Remove the brush roller.
3. Clean the brush roller with the cleaning accessory or a soft cloth. The brush can also be cleaned with water; ensure it is completely dry before reuse.

Installing the Water Tank

1. The mopping cloth is fixed to the water tank with Velcro fasteners.
2. Open and fill the tank with water.
3. Place the tank flat on the floor and close it.
4. Bubbles may appear at points A and B, which is normal.
5. Check if the water has permeated the cloth.
6. Attach the tank under the robot.
7. Carefully place the robot down and start it.

If the robot operates on inclined surfaces, the mopping cloth may not be completely soaked with water. In such cases, tilt the robot to redistribute the bubbles in the tank.

Product Specifications

• Robot Dimensions: Diameter: 330mm, Height: 90mm
• Weight: 3.7kg
• Electronics: Voltage: 14.6V
• Charging Methods: Manual charging / Automatic charging
• Charging Time: 4-6 hours
• Cleaning Time: 100 minutes
• Robot Button Type: Touch

How to Change the Battery

1. Remove the battery cover using a screwdriver.
2. Remove the battery and disconnect it from the robot.
3. Connect a new battery and place it back into the robot's housing (the battery label must face upwards).
4. Reattach the battery cover to its original position and secure it with the screw.

Please use only original batteries. Any other type could lead to damage to the robot vacuum!

Error Codes

• E1: No dustbin in the robot
• E2: No power supply during charging
• E3: Low supply voltage or error during auto-charging
• E11: Left anti-fall sensor detected a drop
• E12: Right anti-fall sensor detected a drop
• E13: Front anti-fall sensor detected a drop
• E21: Left wheel has no ground contact
• E22: Right wheel has no ground contact
• E31: Left bumper infrared detector detects an obstacle
• E32: Right bumper infrared detector detects an obstacle
• E33: Front bumper infrared detector detects an obstacle
• E41: Overload on the left wheel
• E42: Overload on the right wheel
• E43: Overload on the left side brush
• E44: Overload on the right side brush
• E45: Suction attachment overloaded
• E46: Brush attachment overloaded
• LO: Low battery level
• 11:11: Active charging process
• FULL: Battery fully charged
• CONN: Connecting to WiFi

If the above instructions do not help, turn the robot off and restart it. If the error persists, contact support at service-de@proscenic.cn.

Manufacturer Information

Manufacturer: Shenzhen Proscenic Technology Co., Ltd. 5th floor, Jinshun Building, No.287 Ruyi Road, Ailian Community, Longgang District, Shenzhen City, China

Head Office: Taiwan Proscenic Polytron Technologies Inc. Yingyi Street 121 Lane 3rd Lingya District, Gaoxiong City, Taiwan