Quick Start Guide
Pre-Configured Cat6 Surface-Mount Box
Models: N236-004-WH, N236-006-WH
Note: N236-006-WH model shown in the installation diagrams. Installation for the N236-004-WH model is the same.
Available in: English, Español, Français, Русский
Package Contents
- N236-004-WH or N236-006-WH Cat6 Surface-Mount Box
- Double-Sided Tape (x2)
- Cable Ties
- N236-004-WH (x4)
- N236-006-WH (x6)
- Screws (x2)
Installation
Use a flathead screwdriver to carefully pry apart the unit's housing.
Diagram: A flathead screwdriver is shown being used to gently separate the two halves of the surface-mount box. Strip the Cat6 cable's PVC jacket 1 ½ inches (30 mm). Separate the cable wires into four pairs.
Diagram: A Cat6 cable is shown with its outer jacket stripped back approximately 1.5 inches (30 mm), revealing the four twisted pairs of wires. Follow the instructions on the color code sticker to position T568B or T568A wiring. Insert the four wire pairs into the slots accordingly.
Diagram: Shows the punch-down terminals within the surface-mount box. A color-coded sticker indicates wiring order for T568B and T568A standards. Wire pairs are shown being inserted into numbered slots (1-8). T568B Wiring
- Pin 1: White / Orange
- Pin 2: Orange
- Pin 3: White / Green
- Pin 4: Blue
- Pin 5: White / Blue
- Pin 6: Green
- Pin 7: White / Brown
- Pin 8: Brown
T568A Wiring
- Pin 1: White / Green
- Pin 2: Green
- Pin 3: White / Orange
- Pin 4: Blue
- Pin 5: White / Blue
- Pin 6: Orange
- Pin 7: White / Brown
- Pin 8: Brown
Use a punch-down tool (such as Tripp Lite model N046-000) to complete the terminations and cut off any excess wire.
Diagram: A punch-down tool is shown seating a wire into a terminal block and cutting off excess wire. Use the included cable ties to secure the Cat6 cables to the unit's housing.
Diagram: Cable ties are used to bundle and secure installed Cat6 cables to the base of the surface-mount box. Once all cables are secured to the unit's housing, reattach the unit's top cover.
Diagram: The top cover of the surface-mount box is shown being placed back onto the assembled unit.
Warranty & Product Registration
3-Year Limited Warranty
Tripp Lite warrants its products to be free from defects in materials and workmanship for a period of three (3) years from the date of initial purchase. After 90 days from purchase, the obligation is limited to replacing parts on defective products. To obtain service, contact Tripp Lite or an authorized service center. Products must be returned with transportation charges prepaid and accompanied by a description of the problem and proof of purchase. This warranty does not apply to equipment damaged by accident, negligence, misapplication, or alteration. It applies only to the original purchaser who registered the product within 10 days of purchase.
Warranties for Tripp Lite surge suppressors are void if connected to a UPS system output. Warranties for Tripp Lite UPS Systems are void if a surge suppressor is connected to their output receptacles.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for costs such as lost profits, loss of equipment, loss of use, loss of software, loss of data, costs of substitutes, or claims by third parties.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
Protect Your Investment!
Register your product for quicker service and ultimate peace of mind. You could also win an ISOBAR6ULTRA surge protector—a $100 value! Visit www.tripplite.com/warranty.
