Philips TAS2000 Wireless Speaker

Important Information

Safety

Follow these important safety instructions to ensure safe operation of your speaker:

• Ensure the power adapter voltage matches the rating on the product.
• Do not expose the speaker to dripping or splashing.
• Do not place any hazardous sources (e.g., liquid-filled objects, lit candles) on the speaker.
• Ensure adequate ventilation around the speaker.
• Operate the speaker in temperatures between 0°C and 40°C.
• Use only manufacturer-approved attachments/accessories.
• Do not expose the product to liquids without disconnecting the power cable. Do not expose the speaker to water while charging, as this can cause permanent damage. Chemicals, salt, or foreign particles in pools or oceans can damage the water-resistant seals or connector surfaces if not rinsed off after use. Do not charge a wet speaker; allow it to dry completely first.

Battery Safety Precautions

• Risk of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type.
• Do not expose the battery to excessive heat such as sunlight, fire, or similar.
• Battery usage, storage, or transport under extreme high or low temperatures, and low air pressure at high altitudes may pose a safety hazard.
• Do not replace the battery with an incorrect type that can defeat protection (e.g., certain types of lithium batteries).
• Disposing of a battery in a fire or hot oven, or mechanically crushing or cutting a battery, may result in an explosion.
• Leaving a battery in an extremely high temperature surrounding or an extremely low air pressure surrounding that can result in an explosion or the leakage of flammable liquid or gas.

Caring for Your Product

• Clean the product with a microfiber cloth only.
• Your device contains built-in lithium batteries. Battery charging capacity will decrease over time due to self-discharge. To ensure a long battery life, it is recommended to recharge the built-in lithium battery to approximately 50% every 6 months when not in use.

Caution

• Never remove the casing of this speaker.
• Never lubricate any part of this speaker.
• Place the speaker on a flat, hard, and stable surface.
• Do not place this speaker on other electrical equipment.
• Use this speaker indoors only. Keep it away from water, moisture, and liquid-filled objects.
• Do not expose the speaker to direct sunlight, open flames, or heat.
• Risk of explosion if the battery is replaced with an incorrect type.

Your Wireless Speaker

What's in the box

Check and identify the contents of the package:

• Speaker (with cord)
• USB cable
• Quick start guide / safety sheet / warranty

Speaker Overview

Refer to the diagram for button functions:

1. Power: Turn the speaker on or off.
2. Bluetooth/Pairing: Press and hold to enter pairing mode or disconnect from a connected Bluetooth device.
3. Play/Pause/Call: Play or pause audio playback / Answer or reject a call.
4. Volume Up: Increase volume.
5. Volume Down: Decrease volume.
6. Mode/TWS/Auracast™: Press to enter/start Auracast™ receiver mode. Double press to enter/exit TWS mode. Press and hold for over 3 seconds to turn on/off Auracast™ broadcast mode.
7. Light Adjustment: Adjust the lighting effect.
8. Auxiliary Input: Connect an external audio device.
9. USB-C Charging Port: For charging the speaker.

Getting Started

Charge the built-in battery

The speaker is powered by a built-in rechargeable battery.

• Fully charge the built-in battery before first use.

Connect the USB-C port on the speaker to a power source (5V === 2A) using the provided USB cable.

The power indicator LED will be red while charging and turn off when fully charged. A voice prompt will alert you when the battery level is below 20%, and the speaker will automatically turn off if the battery level drops below 2%.

Power On/Off

Press the power button to turn the speaker on or off. You will hear a prompt tone. The speaker will automatically turn off after 15 minutes of no audio signal to save power.

Play from Bluetooth Devices

Connect the speaker to a Bluetooth device

Enjoy audio from your Bluetooth device with this speaker.

• Ensure Bluetooth is enabled on your device.
• The maximum range for pairing is 30 meters (99 feet). Keep away from other electronic devices that may cause interference.

1. Turn on the speaker by pressing the power button. It will automatically enter Bluetooth pairing mode, indicated by a slowly flashing blue light. You can also press and hold the Bluetooth button to enter pairing mode.
2. Enable Bluetooth on your device and select "Philips S2000" from the Bluetooth list.
3. Start streaming music by playing audio on your Bluetooth device.

Bluetooth Indicator

Playback Control

While playing music:

• Press Play/Pause to play or pause.
• Double press to skip to the next track.
• Triple press to skip to the previous track.
• Press Volume Up/Down briefly to adjust volume by one level.
• Press and hold Volume Up/Down to continuously adjust volume.

Phone Call Control

• Press to answer or end a call.
• Press and hold to reject a call.

Auracast™

Use Auracast™ to pair with another S2000 speaker for stereo sound (TWS), receive broadcasts from others, or start your own broadcast to compatible speakers.

Auracast™ Receiver

1. To search for a broadcast, press the Auracast™ button or go to the Entertainment app and select Auracast™ Receiver under Source control. The Auracast™ LED will turn blue, and you will hear a prompt tone. The speaker will automatically search for nearby Auracast™ broadcasts and connect to unencrypted broadcasts with the strongest signal.
2. To exit a broadcast, press and hold the Auracast™ button for 3 seconds or switch to another source in the app.

Auracast™ Transmitter

The default Auracast™ broadcast setting is Public (unencrypted). In the Philips Entertainment app, go to General Settings > Auracast™ Broadcaster to select Personal (encrypted) and set a password.

1. To start broadcasting, press and hold the Auracast™ button for 3 seconds or select Setup PartyLink mode in General Settings within the app. The Auracast™ LED will turn purple (Public) or yellow (Personal), and you will hear a prompt tone.
2. To stop broadcasting, press and hold the Auracast™ button for 3 seconds again or select Unlink in the app. The Auracast™ LED will turn off, and you will hear a prompt tone.

Pairing for Stereo Mode

Two identical Philips S2000 speakers can be paired for stereo sound.

1. The speaker connected to your Bluetooth device will be the primary speaker. Double press the Auracast™ button on both speakers. You will hear a prompt tone. The Auracast™ LED will flash white during pairing and turn pink once connected.
2. In stereo mode, all operations are synchronized between the two speakers. Playback, volume, and lighting can be controlled from either speaker.
3. To exit stereo mode, double press the Auracast™ button on either speaker.

Other Functions

Adjust Lighting

Press the lighting button on the speaker or use the app to control the lighting effects.

Listen to an External Device

• Insert a USB drive into the USB-A port. Music will play automatically.
• Alternatively, use a USB-A to USB-A cable (not included) to connect the device to a computer or other devices, and select "Philips S2000 USB" on the device for audio playback.

Philips Entertainment App

This convenient app allows you to select sources, manage playback, switch between lighting modes, check battery status, and more. The PartyLink mode in the app enables easy connection with other speakers via Auracast™ for a more powerful sound experience.

Download the App

Scan the QR code or press the "Download" button, or search for "Philips Entertainment" in the Apple App Store or Google Play Store.

Pair the App with the Bluetooth Speaker

1. Open the Philips Entertainment app on your mobile device and tap "Add device +" to discover the Philips S2000. Ensure Bluetooth is enabled on your mobile device.
2. When you connect the app to the speaker for the first time, you will be prompted to pair it. Press the power button on your speaker to confirm the app connection.

Sound Control

Once connected to the Entertainment app, you can enjoy additional features and customize your settings.

Light Effect

Control the lighting effects through the app.

Source Control

Use the app to select your audio source: Bluetooth, Auracast™ receiver, or USB. You can also choose different sound modes like Relaxation, Concentration, Masking, Generative, Ambient, or Nature.

General Settings

You may notice new firmware updates available for your speaker.

Auracast™ Broadcasts

Public broadcasts allow other Auracast™ devices to listen without a password. Personal broadcasts are encrypted and require a password.

PartyLink Mode Setup

To purchase more S2000 speakers or other Philips speakers supporting Auracast™ and enjoy PartyLink, follow the in-app instructions to easily pair them.

What is PartyLink Mode?

This mode links various speakers with Auracast™ technology to create a party sound experience. The Primary speaker plays audio and broadcasts it to other Secondary speakers.

Product Information

General Information

Speaker

Bluetooth

Troubleshooting

General

No Power

• Ensure the speaker is fully charged.
• Ensure the USB power source is correctly connected.
• The speaker automatically turns off after 15 minutes of inactivity to save energy.

No Sound

• Adjust the volume on this speaker.
• Adjust the volume on the connected device.
• Ensure your Bluetooth device is within range.

Bluetooth

Poor Audio Quality After Connecting to a Bluetooth Device

• Weak Bluetooth reception. Move the device closer to the speaker or remove any obstructions.

Cannot Find [Philips S2000] in Bluetooth Device Pairing List

• To enter Bluetooth pairing mode, press and hold the Bluetooth button for 3 seconds, then try again.

Cannot Establish Connection with Your Bluetooth Device

• Ensure Bluetooth is enabled on your device. Refer to your device's user manual.
• The speaker is not in pairing mode.
• The speaker is already connected to another Bluetooth device. Disconnect and try again.

Notices

Modifications

Any changes or modifications not expressly approved by MMD Hong Kong Holding Limited may void the user's authority to operate the product.

Compliance

TP Vision Europe B.V. hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive RED 2014/53/EU and the UK Radio Equipment Regulations SI 2017 No 1206. The Declaration of Conformity can be found at www.philips.com/support.

Environmental Care

Disposal of Old Product and Battery

Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused. Please dispose of the product and batteries according to local regulations. Do not dispose of them with regular household waste. Proper disposal helps prevent negative consequences for the environment and human health.

Removing the Built-in Battery

Please inquire about your local system for the separate collection of electrical and electronic products and batteries. Follow local regulations for product and battery disposal. Proper disposal of old products and batteries helps prevent negative consequences for the environment and human health.

Trademarks

Bluetooth®

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

AURACAST™

The Auracast™ name and logos are trademarks owned by Bluetooth SIG, Inc., and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

Unauthorized copying of copyrighted material, including computer programs, files, broadcasts, and sound recordings, may be a violation of copyright law and is punishable by law. Do not use this equipment for such purposes.