Gembird Mobile Lecture Desk with Caster Wheels

General Information

This product is manufactured by Gembird Europe B.V. For inquiries regarding product compliance in Europe, contact Gembird Europe B.V., Wittevrouwen 56, 1358 CD, Almere, The Netherlands. Visit www.gmb.nl for warranty conditions and product support.

Safety: Follow the safety advice provided on www.gmb.nl/safety for safe handling of the product.

Warranty Conditions: The receipt must clearly list the date of purchase and part number. Keep the receipt for the entire warranty period for all claims. Gembird Europe B.V. reserves the right to credit, repair, or replace defective items at the manufacturer's expense. Warranty work does not extend the warranty period. Claims for damages due to misuse, abuse, or external impact (falling, impact, water ingress, dust, contamination, breakage) are void. Wear parts (e.g., rechargeable batteries) are excluded. Gembird Europe B.V. may choose between replacement or credit note for RMA goods, calculated at current market value.

Maximum Loading Weight:

• Tabletop: 44 lbs (20 kg)
• Shelf: 22 lbs (10 kg)

Exceeding these weights can damage the product and create safety hazards.

Package Content

• A(x1): Tabletop
• B(x1): Shelf
• C(x2): Braked Casters
• D(x2): Non-braked Casters
• E(x1): Left Column Assembly
• F(x1): Right Column Assembly
• G(x1): Base Assembly
• H(x1): Column connection plate
• I(x2): Shelf Support
• J(x1): Drawer
• K(x1): Left Rotation Panel
• L(x1): Right Rotation Panel
• M(x2): Quick Lock Handle
• N(x2): Reinforcement
• S-A(x17): M6x12 screws
• S-B(x2): M6x16 screws
• S-C(x3): D6.4xD16x1.6 Plastic Flat Washer
• S-D(x3): D6.4xD16x1.6 Flat Washer
• S-E(x5): M5x12 screws
• T-A(x2): M8x35 screws
• T-B(x1): 4mm wrench
• T-C(x1): 5mm wrench
• T-D(x1): 5mm wrench

Installation Steps

1. Step 1

   Install the 4 casters onto the base assembly (G). Use the (T-D) wrench to tighten the casters clockwise. Place braked casters at the front and non-braked casters at the back.

2. Step 2

   Rotate the rotary knob on the column counterclockwise and adjust the column height using the one-way knob.

3. Step 3

   Place the left column assembly (E) and right column assembly (F) into the base's limit positioning round holes. Place reinforcement plates (N) at the bottom. Align (T-A) screws with the center holes and tighten using the (T-C) wrench clockwise.

4. Step 4

   Install the column connection plate (H). Align it with the inner holes of the left and right columns and tighten the four (S-A) screws using the (T-B) wrench.

5. Step 5

   Install the shelf support (I). Align it with the front holes of the left and right columns and tighten the four (S-A) screws using the (T-B) wrench.

6. Step 6

   Install the shelf (B). Align it with the left and right support holes and tighten the four (S-A) screws using the (T-B) wrench. Adjust the shelf support (I) by bending it to align with the shelf holes if necessary.

7. Step 7

   Install the drawer (J). Align it with the holes below the shelf and tighten the four (S-E) screws using the (T-C) wrench.

8. Step 8

   Install the left and right rotation plates (K) and (L). Ensure the arc slots face the front. Align with the embedded nut holes of the shelf and tighten the four (S-A) screws using the (T-B) wrench.

9. Step 9

   Install the tabletop assembly (A). Align the circular holes of the rotation plate with the 1st nuts on both sides of the columns and tighten the two (S-B) screws using the (T-B) wrench.

10. Step 10

    Thread the quick lock handle (M) through the (S-D) flat washer, (S-C) plastic flat washer, and the waist hole of the rotation plate. Screw it into the 2nd nut at the top of the column and tighten.

11. Step 11

    Adjust the quick lock handle (M) to achieve the 40° tilt function. Adjust the rotary knob to achieve the up and down height adjustment function.

12. Step 12

    Installation is complete. The desk can now be used to hold a laptop.