RadioShack 4-1 Family Favorites Remote User Guide

Introduction

Thank you for purchasing a RadioShack 4-1 Family Favorites Remote. This remote allows you to control up to four home entertainment devices with one easy-to-use, compact unit. It also enables setting up favorite channels for different family members (Mom, Dad, kids).

After installing batteries, the remote can immediately control an RCA TV, VCR, DVD player, and Satellite receiver. For other brands, follow the programming instructions. For best results, read all instructions and keep this guide for future reference.

Installing Batteries

The RadioShack 4-1 Family Favorites Remote requires four AAA batteries (not supplied).

Battery Use And Safety

• Use only fresh batteries of the required size and recommended type.
• Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities.

CAUTION: If the remote will not be used for an extended period, remove the batteries to prevent chemical leakage that could damage electronic parts.

WARNING: Dispose of old batteries promptly and properly. Do not burn or bury them.

To Install Batteries:

1. Open the battery compartment cover on the back of the remote.
2. Place the AAA batteries in the compartment, matching the + and - polarity symbols.
3. Replace the cover.

NOTE: When the remote stops operating properly, replace the batteries within 10 minutes to preserve programming information.

A Quick Look at the Controls

Programming a Device

The remote is pre-programmed for RCA devices. To control other brands:

1. Turn on the device and load media if necessary.
2. Press the desired device key (TV, VCR, DVD, CBL/SAT).
3. Press and hold the P key until the red LED blinks twice, then release.
4. Enter the first four-digit code for your device. The LED blinks once per digit. It blinks twice if the code is correct.
5. Aim the remote at the device and press Power (or PLAY if no Power key). The device should turn off. If not, repeat steps 2-5 with other codes for your brand. If no code works, see "Searching for Your Code".
6. Repeat for each device. Record working codes for future reference.

NOTE: For TV/DVD, TV/VCR/DVD, or TV/VCR Combos, use the TV key. For PVRs, use the VCR key. For HTiBs, use the DVD key. VCR/DVD combos may require programming for both VCR and DVD codes.

Searching for Your Code

If listed codes don't work or your brand isn't listed, use the search function:

1. Press the device key (e.g., TV).
2. Press and hold P until the red LED blinks twice, then release.
3. Enter 991. The LED blinks twice.
4. Aim the remote at the device and press Power. The remote sends codes sequentially.
5. If the device responds, proceed to step 6. If not, press CH+ to try the next code. Continue until the device responds. (Press CH- to try the previous code).
6. To lock the code, press P once. The LED blinks twice.
7. Repeat for other devices, substituting the appropriate device key.

Checking the Codes

To find out which code is currently operating a device:

1. Press the device key (e.g., TV).
2. Press and hold P until the red LED blinks twice, then release.
3. Enter 990. The LED blinks twice.
4. To find the first digit, press 1. Count the LED blinks (e.g., 3 blinks = 3). Write down the number. (0 blinks = 0).
5. Repeat step 4 for the remaining digits using keys 2, 3, and 4.
6. Repeat for other devices by substituting the appropriate key.

Reassigning Device Keys

You can reassign unused device keys (e.g., VCR) to control a second device of another type (e.g., DVD player):

1. Press and hold P until the red LED blinks twice, then release.
2. Enter 992. The LED blinks twice.
3. Press the new device key (e.g., DVD), then the key to be reassigned (e.g., VCR). The VCR key is now ready to be programmed for the second DVD player.

To reassign other keys, substitute the appropriate device key in step 3. To clear a reassigned mode, repeat steps 1-2 and press the mode key twice.

Programming Favorite Channel Scan

Store up to 10 favorite channels for quick scanning:

NOTE: Only channels from one device can be stored for this feature.

1. Press a device key.
2. Press and hold P until the red LED blinks twice, then release.
3. Enter 996. The LED blinks twice.
4. Enter a favorite channel number (e.g., 031) and press P (if less than 5 digits or 4 digits plus Enter).
5. Repeat step 4 for up to 10 channels.

NOTES:

• Entering more than 10 channels or a 10-second pause exits programming.
• If your device requires an Enter key after channel numbers, press it during programming.
• To exit with fewer than 10 channels, press and hold P for three seconds. The LED blinks twice.
• If you entered fewer than 10 channels and want to add more, you must re-enter all channels.
• To program new channels after reaching 10, reset the remote (see Troubleshooting).

Using Channel Scan

Use the FAV (Scan) key to scan favorite channels or all channels:

1. Press a device key.
2. Press SCAN once.

The remote scans favorite channels first (if programmed), then all channels. If Favorite Channel Scan is not set up, scanning starts from the current channel.

Press any key to stop scanning at any time.

Setting Family Favorites

Customize four genre keys (News, Movies, Sports, Family) for up to three users (Mom, Dad, Kids). Each genre key can store up to three channels.

To set up a scan key:

1. Press and hold P until the LED blinks twice, then release.
2. Enter 995. The LED blinks twice.
3. Press a user key (e.g., Mom's).
4. Press a genre key (e.g., News).
5. Press the device key (e.g., TV), followed by the desired channel number (up to 3 digits).
6. Press and hold P for three seconds. The red LED blinks twice.
7. Repeat for each channel. Entering more than three channels overwrites the first.

NOTES:

• If your device requires an Enter key after channel numbers, press it during programming.
• If you entered fewer than three channels and want to add more, you must re-enter all channels for that user and genre.
• To clear a genre key, follow steps 1-6 but do not enter a mode or channel at step 5.

Using Family Favorites

To access programmed favorite channels:

1. Press the user key (Mom's, Dad's, Kid's).
2. Press the genre key (e.g., Sports). The remote accesses the first programmed channel.
3. Press the genre key again to access the next programmed channel for that user and genre.

Setting the Power Macro

Program the Power key to perform a sequence of actions (up to 15 commands):

1. Press and hold P until the red LED blinks twice, then release.
2. Enter 995. The LED blinks twice.
3. Press Power.
4. Enter the series of commands for the macro.
5. Press and hold P until the red LED blinks twice, then release.

Pressing and holding the Power key for about 2 seconds will execute the macro. To clear the macro, repeat steps 1-5 without entering commands in step 4.

NOTE: User or genre keys cannot be included in the Power macro.

Changing Volume Lock

The remote defaults to independent volume control for each device (Global Volume Unlock). You can change this to Global Volume Lock (one device controls all volume) or Individual Volume Unlock.

Locking Volume Control to One Mode (Global Volume Lock)

1. Press and hold P until the red LED blinks twice, then release.
2. Enter 993, then press the desired device key (e.g., TV). The LED blinks twice. Now, VOL+, VOL-, or Mute on that device will control volume across all modes.

Unlocking Volume Control for a Single Device (Individual Volume Unlock)

1. After Global Volume Lock, press and hold P until the red LED blinks twice, then release.
2. Press the device key for independent volume control.
3. Enter 993, then press VOL-. The LED blinks four times.
4. Repeat for other devices needing independent control.

Unlocking All Volume Control (Restoring Global Unlock)

1. Press and hold P until the red LED blinks twice, then release.
2. Enter 993, then press VOL+. The LED blinks four times. All devices will now have independent volume control.

Troubleshooting

• PROBLEM: LED does not blink. SOLUTION: Replace batteries with four new AAA alkaline batteries.
• PROBLEM: LED blinks, but device does not respond. SOLUTION: Ensure the remote is aimed at the device and is within 15 feet.
• PROBLEM: LED blinks one long blink. SOLUTION: An entry error occurred. Try the sequence again.
• PROBLEM: Remote does not control devices or commands are not working properly. SOLUTION: Try all listed codes for the device. Ensure the device uses an infrared remote control.
• PROBLEM: CH+, CH-, and LAST keys do not work for RCA TVs (1983-1987 models). SOLUTION: Only the original remote control operates these functions for these specific models.
• PROBLEM: No volume on a second TV. SOLUTION: Refer to "Changing Volume Lock".
• PROBLEM: Channels do not change properly. SOLUTION: If the original remote required an Enter key, press Enter on this remote after entering the channel number.

For more help, contact rshelp@ueic.com.

Manufacturer's Codes

The remote includes codes for various home entertainment devices. Below are examples for each category:

Setup Codes for Cable Boxes (Converters)

• ABC: 0003, 0008, 0014, 0017
• Archer: 0153, 0039, 0797, 0022, 0207
• General Instrument: 0476, 0276, 0003
• Jerrold: 0476, 0276, 0003, 0012, 0014, 0015
• RadioShack: 0797, 0315, 0303, 0883, 0015
• Zenith: 0000, 0525, 0899
• ...and many more.

Setup Codes for DVD Players

• Aiwa: 0641
• Apex Digital: 0672, 0717, 0755, 0796, 0797, 1100, 1061, 1937, 0794, 1056, 1915
• Denon: 0490, 0634
• JVC: 0558, 0623, 0867, 1940, 1901
• Panasonic: 0490, 1925, 1907, 1762, 1990
• Sony: 0533, 0864, 1903, 1981, 1033, 1934, 1904
• ...and many more.

Setup Codes for HTiBs (Home-Theater-in-a-Box)

• Aiwa: 0641
• Apex Digital: 1937, 1915
• JVC: 1940, 1901
• Magnavox: 1976
• Panasonic: 1907, 1990, 1925
• Sony: 1904, 1903, 1981, 1934
• ...and many more.

Setup Codes for Satellite Receivers

• DirecTV: 0392, 0566, 0639, 1639, 1142, 0247, 0749, 1749, 0724, 0819, 1856, 1076, 1109, 0099, 1442
• Echostar: 1005, 0775, 0218, 0269, 1170
• Hughes Net. Sys.: 1142, 0749, 1749, 1442
• Philips: 1142, 0749, 1749, 0724, 1076, 0722, 0099, 1442
• RCA: 0392, 0566, 0855, 0143
• Sony: 0639, 1639
• ...and many more.

Setup Codes for TVs

• Admiral: 0093, 0463
• Apex Digital: 0748, 0765, 1943, 0767
• Emerson: 0154, 0236, 0463, 0180, 0178, 0171, 1909, 1929, 0282, 1905, 1928, 0280, 0623, 1911, 0039, 1944, 0177
• GE: 0047, 0051, 0451, 0178, 0747, 1907, 1922, 0027, 0055, 1347, 1919, 0282, 1147, 1917
• Magnavox: 0054, 0030, 1454, 0706, 1931, 0020, 0186, 1254, 1913, 1904, 0386
• Panasonic: 0250, 0051, 1924, 1946, 0055, 1919, 1941, 0650, 1927
• RCA: 0047, 1447, 1247, 1547, 1919, 0018, 0679, 1147, 1953, 1917, 1948, 0090, 1047, 1347, 1907, 1922, 0747
• Sony: 0000, 1925, 1904, 0080
• Zenith: 0017, 0463, 0178, 1909, 0092, 1904, 1929, 1911
• ...and many more.

Setup Codes for TV/DVD Player Combos

• Apex Digital: 1943
• Panasonic: 1941
• RCA: 1948
• Sony: 1903
• Toshiba: 1935
• ...and many more.

Setup Codes for TV/VCR Combos

• Emerson: 0236, 1909, 1929, 1905, 1928, 1911
• Magnavox: 1904, 1931, 1913
• Panasonic: 1919, 1927, 1924
• RCA: 1922, 1919, 1917, 1907
• Sony: 1925, 1904
• Zenith: 1904, 1929, 1911
• ...and many more.

Setup Codes for VCRs

• Admiral: 0048, 0209
• Emerson: 0037, 0184, 0000, 0121, 0043, 0209
• GE: 0060, 0035, 0240, 0202, 1060
• Magnavox: 0035, 0039, 0081, 0000, 0593
• Panasonic: 1062, 0035, 0162, 0616, 1262, 0454, 1162
• RCA: 0060, 0240, 0042, 0619, 0058, 1060, 0202, 0880
• Sony: 0035, 0032, 0033, 0000, 0636
• Zenith: 0039, 0033, 0000, 0209
• ...and many more.

Setup Codes for DBS/PVR Combinations

• DirecTV: 0392, 0566, 0639, 1639, 1142, 0247, 0749, 1749, 0724, 0819, 1856, 1076, 1109, 0099, 1442
• Echostar: 1005, 0775, 1170
• Hughes Network Systems: 1142, 1442
• ...and many more.

Setup Codes for TV/VCR/DVD Combinations

• Emerson: 1944
• Panasonic: 1946
• Sharp: 1917, 0630
• Toshiba: 1945
• ...and many more.

Setup Codes for PVRs

• Panasonic: 0616
• ReplayTV: 0616, 0614
• Sony: 0636
• Tivo: 0636, 0618
• ...and many more.

Refer to the full manual for a complete list of codes.

Care

• Keep the remote dry. Wipe immediately if it gets wet.
• Use and store in normal temperature environments.
• Handle gently; do not drop.
• Wipe with a damp cloth to keep it looking new.

Modifying internal parts can cause damage and void the warranty. For issues, contact www.radioshack.com or visit a RadioShack store.

Specifications

• Power: (4) AAA Batteries
• Size (H x W x D): 7.67 x 2.44 x 1.42 in. (195 x 62 x 36 mm)
• Weight (w/o batteries): 4.76 oz (136 g)

Specifications are typical and subject to change without notice.

FCC Notice

This equipment complies with FCC Part 15 for Class B digital devices. It may cause interference if not installed and used correctly. If interference occurs, try reorienting the antenna, increasing separation, using a different outlet, or consulting a technician.

Shielded cables must be used. Modifications without manufacturer approval may void user authority.

Limited 90-Day Warranty

This product is warranted by RadioShack against manufacturing defects for ninety (90) days from the date of purchase. RadioShack makes no express warranties beyond this, and implied warranties are limited to the duration of this written warranty. RadioShack is not liable for indirect, special, incidental, or consequential damages.

Warranty service requires the product and proof of purchase at a RadioShack store. RadioShack may repair, replace, or refund the purchase price.

The warranty does not cover damage from acts of God, abuse, misuse, improper installation/maintenance, alteration, lightning, or unauthorized repairs. It also excludes consumables (batteries), cosmetic damage, and shipping costs.

This warranty provides specific legal rights, which may vary by state.

Contact RadioShack Customer Relations at 200 Taylor Street, 6th Floor, Fort Worth, TX 76102.