JURA IMPRESSA Z5 Generation II Quick Reference Guide

The 'IMPRESSA Manual' together with these short instructions 'IMPRESSA Z5 – Quick Reference Guide' has been awarded the seal of approval by the independent German Technical Inspection Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.

Image: A front view of the JURA IMPRESSA Z5 Generation II automatic coffee machine, showcasing its sleek design and control panel.

Switching On

These short instructions do not replace the 'IMPRESSA Z5 Generation II Manual'. Make sure you read and observe the safety information and warnings first in order to avoid hazards.

When the IMPRESSA is switched on, a prompt for the rinse operation automatically appears, which is initiated by pressing the maintenance button.

Precondition

Your IMPRESSA is switched on at the power switch and the On/Off button is illuminated (standby).

1. Press the On/Off button to switch the IMPRESSA on.
2. The display shows: WELCOME TO JURA, UNIT IS HEATING. The maintenance button lights up.
3. Place a receptacle under the coffee spout.
4. Press the maintenance button.
5. The machine rinses itself, stopping automatically. The display shows: COFFEE READY. Your IMPRESSA is ready to use.

Image: A close-up of the JURA coffee machine's milk frothing system, showing the wand and milk pipe connection.

Latte Macchiato

Your IMPRESSA prepares a latte macchiato at the touch of a button.

Example: Preparing a Latte Macchiato

Precondition

COFFEE READY is shown on the display.

• Remove the milk pipe from the packaging of the vacuum milk container. For a milk carton/bottle, use the long pipe; for the vacuum milk container, use the short pipe.
• Attach the milk pipe to the Frother.
• Insert the other end into a milk carton/bottle or connect it to the vacuum milk container.
• Place a glass under the Cappuccino Frother.
• Turn the selection lever of the Frother to the milk foam position [milk-foam].
• To enable the typical layers of a Latte Macchiato to form more effectively, add 10 ml of cool milk to the glass before preparing this specialty.
• You can refine your Latte Macchiato further by adding a little flavored syrup to the glass.
• Press the Latte Macchiato button.
• The display shows: 1 LATTE MAC. and the coffee strength.
• The display shows: 1 LATTE MAC. / MILK, the milk foam is being prepared. The operation stops automatically after reaching the pre-set amount of milk.
• The display shows: 1 LATTE MAC. A brief interval follows during which the hot milk separates from the milk foam, enabling the formation of typical latte macchiato layers.
• The display shows: 1 LATTE MAC. / COFFEE, coffee preparation starts. Preparation stops automatically after reaching the pre-set amount of water. COFFEE READY is shown on the display.

To ensure that the Cappuccino Frother works perfectly, rinse and clean it regularly. Descriptions can be found in the 'Cappuccino Frother' section.

Image: A glass positioned under the JURA coffee machine's milk frothing system, ready for beverage preparation.

Using and Activating Filter

Your IMPRESSA no longer has to be descaled if you use the CLARIS filter cartridge.

Perform the 'Insert filter' operation without interruption. This will ensure that your IMPRESSA always produces its best.

Precondition

COFFEE READY is shown on the display.

• Keep the Rotary Switch pressed until MAINTENANCE appears on the display.
• Turn the Rotary Switch until FILTER I.P.H.S. is displayed.
• Press the Rotary Switch to enter the programme item. The display shows: FILTER NO.
• Turn the Rotary Switch until FILTER YES is displayed.
• Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display.
• The display shows: INSERT FILTER / PRESS BUTTON, the maintenance button lights up.
• Remove a CLARIS filter cartridge and the filter cartridge extension from the Welcome Pack.
• Place the extension on top of the filter cartridge.
• Remove the water tank and empty it.
• Lift the cartridge holder and insert the filter cartridge into the water tank, applying slight pressure.
• Close the cartridge holder. It will click into place audibly.
• Fill the water tank with fresh, cold water and reinsert.
• Place a receptacle (containing at least 500 ml) under the Cappuccino Frother.
• Turn the selection lever of the Frother to the steam position [steam].
• Press the maintenance button. The display shows: FILTER RINS., water will flow out of the Frother.

Image: A close-up of the JURA coffee machine's water tank with a filter cartridge inserted.

Image: The JURA coffee machine with its milk frothing system, ready for filter rinsing.

Filter Change

• You can interrupt filter rinsing at any time by pressing any button.
• The water may be slightly discoloured. This is not harmful to health and does not affect the taste.
• Filter rinsing stops automatically after approx. 500 ml. COFFEE READY appears on the display. The filter is now activated.

After 50 litres of water have flowed through the filter, or after two months, its capacity is reached. Your IMPRESSA will automatically prompt you to change the filter.

If the CLARIS filter cartridge is not activated, you will not be prompted to change the filter.

To change the CLARIS filter cartridge when prompted:

Precondition

COFFEE READY / FILTER CHANGE is displayed and the maintenance button lights up.

• Press the maintenance button. The display shows: CHANGE TIME 2 MIN / START YES.
• If you want to change the filter at a later point, turn the Rotary Switch until CHANGE / START NO is displayed. Exit the maintenance programme by pressing the Rotary Switch. The prompt 'change filter' remains on the display.
• Press the maintenance button. The display shows: INSERT FILTER / PRESS BUTTON.
• Remove the water tank and empty it.
• Open the cartridge holder and remove the old CLARIS filter cartridge and the extension.
• Fit the extension on top of a new CLARIS filter cartridge.
• Insert the filter cartridge into the water tank, exerting slight pressure.
• Close the cartridge holder. It will click into place audibly.
• Fill the water tank with fresh, cold water and reinsert.
• Place a receptacle (containing at least 500 ml) under the Cappuccino Frother.
• Turn the selection lever of the Frother to the steam position [steam].
• Press the maintenance button. The display shows: FILTER RINS., water flows from the Frother.
• You can interrupt filter rinsing at any time by pressing any button.
• The water may be slightly discoloured. This is not harmful to health and does not affect the taste.
• Filter rinsing stops automatically after approx. 500 ml. Your IMPRESSA heats up and is once again ready to use.

Clean Machine

After 220 coffee preparations or 80 switch-on rinses, the IMPRESSA will prompt you to clean it.

CAUTION

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. Use only original JURA care products.

• The cleaning programme only lasts about 20 minutes.
• Do not interrupt the cleaning programme; the quality of cleaning will be impaired if you do so.
• JURA cleaning tablets are available from stockists.

Precondition

COFFEE READY / CLEAN is displayed and the maintenance button lights up.

• Press the maintenance button. The display shows: CLEANING TIME 20 MIN / START YES.
• If you want to clean the machine at a later point, turn the Rotary Switch until CLEANING / START NO is displayed. Exit the maintenance programme by pressing the Rotary Switch. The prompt 'clean machine' remains on the display.
• Press the maintenance button. The display shows: TRAY / GROUNDS EMPTY.
• Empty the drip tray and coffee grounds container and put them back into the machine.
• Press the maintenance button. The display shows: PRESS BUTTON. The maintenance button lights up.
• Place a receptacle under the coffee spout and the Cappuccino Frother.
• Press the maintenance button. The display shows: MACHINE IS CLEANING, water flows out of the coffee spout.
• The process is interrupted. The display shows: ADD TABLET.
• Open the cover of the bean container.
• Open the cover of the filler funnel for pre-ground coffee.
• Insert a JURA cleaning tablet into the filler funnel.
• Close the cover of the filler funnel and the cover of the bean container.
• Press the maintenance button. The display shows: PRESS BUTTON. The maintenance button lights up.
• Press the maintenance button. The display shows: MACHINE IS CLEANING, water flows out of the coffee spout and the Cappuccino Frother several times.
• The process is interrupted. The display shows: TRAY / GROUNDS EMPTY.
• Empty the drip tray and coffee grounds container and put them back into the machine.

The cleaning operation is now complete. The IMPRESSA is once more ready for use.

Image: Close-up of the JURA coffee machine's control panel and drip tray area.

Descale Machine

The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.

CAUTION

If the descaling agent comes into contact with the skin or eyes, this can cause irritation.

• Avoid contact with the skin or eyes.
• Rinse the descaling agent off with clean water. Should you get any descaling agent in your eye, consult a doctor.

CAUTION

If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. Use only original JURA care products.

CAUTION

If the descaling operation is interrupted, there may be damage to the machine. Allow the descaling programme to run to the end.

CAUTION

If the descaling agent comes into contact with sensitive surfaces, damage cannot be ruled out. Clean up any splashes immediately.

• The descaling programme lasts approx. 45 minutes.
• JURA descaling tablets are available from stockists.
• If you use a CLARIS filter cartridge and this is activated, you will not be prompted to descale the machine.

Precondition

COFFEE READY / DESCAL is displayed and the maintenance button lights up.

• Press the maintenance button. The display shows: DECALCIFYING TIME 45 MIN / START YES.
• If you want to descale the machine at a later point, turn the Rotary Switch until DECALCIFYING / START NO is displayed. Exit the maintenance programme by pressing the Rotary Switch. The prompt 'Descale machine' remains on the display.
• Press the maintenance button. The display shows: TRAY / GROUNDS EMPTY.
• Empty the drip tray and coffee grounds container and put them back into the machine.
• Remove the water tank and empty it.
• Completely dissolve the contents of one blister (3 JURA descaling tablets) in a container that holds 600 ml of water. This may take several minutes.
• Pour the solution into the empty water tank and insert it in the machine.
• The display shows: SOLVENT IN TANK / PRESS BUTTON, the maintenance button lights up.
• Remove the Cappuccino Frother.
• Place a receptacle under the hot water spout and the connector of the Frother.
• Press the maintenance button. The display shows: MACHINE IS DECALCIFYING. Water flows from the hot water spout and the connector of the Frother. The maintenance button blinks during the descaling operation.
• The process stops automatically. The display shows: TRAY / GROUNDS EMPTY.
• Empty the receptacles below the hot water spout and the connector of the Frother.
• Empty the drip tray and coffee grounds container and put them back into the machine.
• The display shows: WATER TANK FILL.
• Remove the water tank and rinse it thoroughly.
• Fill the water tank with fresh, cold mains water and reinsert.
• Press the maintenance button. The display shows: PRESS BUTTON, the maintenance button lights up.
• Replace the Cappuccino Frother.
• Place a receptacle under the hot water and coffee spout and the Cappuccino Frother.
• Press the maintenance button. The display shows: MACHINE IS DECALCIFYING, water flows out of the hot water spout and the Cappuccino Frother. The display shows: UNIT IS HEATING, RINSING, water flows out of the coffee spout.
• The process stops automatically. The display shows: TRAY / GROUNDS EMPTY.
• Empty the drip tray and coffee grounds container and put them back into the machine.

The descaling operation is now complete. Your IMPRESSA heats up and is once again ready to use.

If the descaling operation stops unexpectedly, rinse the water tank thoroughly.

Image: A measuring jug with water and a blister pack of JURA descaling tablets.

Image: The JURA coffee machine with its milk frothing system, during the descaling process.

Rinsing the Cappuccino Frother

Each time milk has been prepared, the IMPRESSA displays a prompt for cappuccino rinsing.

Precondition

COFFEE READY / CAPPU RINSE is shown on the display, the maintenance button lights up.

• Place a receptacle under the Cappuccino Frother.
• Turn the selection lever of the Frother to the steam position [steam].
• Press the maintenance button. The display shows: CAPPUCCINO RINSING, the Cappuccino Frother is rinsed.
• The procedure stops automatically. COFFEE READY appears on the display.

Cleaning the Cappuccino Frother

To ensure that the Cappuccino Frother works perfectly, you should clean it daily when you have been preparing milk.

CAUTION

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. Use only original JURA care products.

• The IMPRESSA will not prompt you to clean the Cappuccino Frother.
• The JURA Cappuccino Cleaner is available from stockists.

Precondition

COFFEE READY is shown on the display.

• Keep the Rotary Switch pressed until MAINTENANCE appears.
• Press the Rotary Switch to enter the programme item. The display shows: CAPPUCCINO CLEANING.
• Press the Rotary Switch. The display shows: CLEANER FOR CAPPUCCINO / PRESS BUTTON.
• Pour 250 ml of fresh water into a container and add one capful (max. 15 ml) of Cappuccino Cleaner.
• Immerse the milk pipe in the receptacle.
• Turn the selection lever to the milk foam position [milk-foam] or milk [milk].
• Place another receptacle under the Cappuccino Frother.
• Press the maintenance button. The display shows: CAPPUCCINO CLEANING, the Frother and pipe are cleaned.
• The display shows: WATER FOR CAPPUCCINO / PRESS BUTTON.
• Rinse the receptacle thoroughly, fill it with approx. 250 ml of fresh water and immerse the milk pipe in the water.
• Empty the receptacle and place it under the Frother once more.
• Press the maintenance button. The display shows: CAPPUCCINO CLEANING, the Frother and pipe are rinsed with fresh water.

COFFEE READY appears on the display. Your IMPRESSA is once more ready to use.

Image: A bottle of JURA Cappuccino Cleaner and a measuring cup.

Image: The JURA coffee machine's milk frothing system, being cleaned.

Dismantle and Rinse the Cappuccino Frother

• Carefully pull off the Cappuccino Frother.
• Dismantle the Cappuccino Frother completely.
• Rinse all the Frother parts thoroughly under running water.
• Reassemble the Cappuccino Frother and attach it once more to the connector.

Diagram: An exploded view illustrating the parts of the JURA coffee machine's Cappuccino Frother for dismantling and cleaning.