Dewenwils LED Floor Lamp

CAUTION

1. Before assembly, place all parts out on a clean flat surface and inspect each part for defects that may have occurred during shipping.
2. Inspect wire insulation for any cuts, abrasions or exposed copper that may have resulted during shipping. If there are any defects in the wire, DO NOT continue to assemble. Please send an email to our Customer Service immediately.
3. Consult a qualified electrician if you have any electrical questions.
4. Never drape clothes over the lamp.
5. To reduce the likelihood of tipping over, we recommend placing the lamp behind furniture and keep children and pets away.
6. To prevent children from suffocating and choking, keep them away from packing materials.
7. Please keep this manual and hand it over when you transfer the product.

Packing List

The packing list includes:

• 1: Column Floor Lamp
• 2: Base
• 3: Adapter
• 4: Remote Control
• 5: Instruction Manual

A diagram shows the components labeled 1 through 5, with a separate diagram illustrating the adapter connection (3).

ASSEMBLY INSTRUCTIONS

Detailed assembly steps are provided with diagrams:

Step 1: Screw the Column Floor Lamp (A) clockwise onto the Base (B) until tight.

Step 2: Connect the Adapter connector (D) to the Adapter (C) and then Spin lock (3).

Step 3: Place the floor lamp where you need it and plug into the power supply.

FUNCTIONS

Foot Switch

The foot switch offers:

• Three color temperatures: 3000K/4500K/6000K
• Stepless Dimmable brightness

Operation:

• Press the switch once to turn the light ON.
• Short press the button to cycle through color temperatures (3000K/4500K/6000K).
• Short press the button again to turn the light OFF.
• After turning the light ON, long press the foot switch to gradually brighten or darken the light. Release when the desired brightness is reached.

Remote Control

The remote control has the following buttons:

1. Shutdown button: Long press for 3 seconds until the blue light flashes to unpair the floor lamp and remote control. Re-pairing with another remote is possible.
2. Brightness + (7 levels)
3. Brightness - (7 levels)
4. Color temperatures: 3000K/4500K/6000K
5. Power button: Power on the lamp, install a 12V 23A battery in the remote. Press and hold the power button for 3 seconds until the blue light flashes once for successful code matching.
6. Color temperature + (7 levels)
7. Color temperature - (7 levels)
8. Night light mode: Sets CCT to 3000K with 30% brightness.

Memory function: The floor lamp remembers the last set brightness and color mode before being turned off.

Specifications

• Product Height: 57.5 IN
• Base Length: 7.8 IN
• Wire Length: 70 IN
• Materials: Iron, PC
• Input Voltage: AC100V-240V 60Hz
• Max. Load Power: 19W
• Max. Lumens: 1100LM
• Color temperature: 3000K/4500K/6000K

One Year Limited Warranty

DEWENWILS warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase. Warranty is void if damage is caused by misuse or improper installation. Our dedicated customer service team will get back to you within 24 hours.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.