Outsunny 84A-316V00 Garden Swing Chair
Model: 84A-316V00 | Part Number: IN231000518V01_GL
Introduction
Thank you for purchasing this Outsunny garden swing chair. Please read this manual carefully for proper use, assembly, and maintenance to ensure your enjoyment and safety.
Important Safety Information & Precautions
General Safety:
- For domestic use only.
- Place the swing chair stably on a flat floor.
- Mount the garden chairs under shelter or a canopy.
- Keep away from open flames and heat sources.
- Do not hang anything on the structure.
- Do not exceed the maximum weight capacity of 240kg.
- It is advised not to remain on the chairs during storms or adverse weather conditions.
- Cover the furniture when not in use to protect it from the elements.
Before Assembly:
- Prepare a clean and dry assembly area.
- Verify that the product is not damaged.
- Check that none of the pieces are missing.
Assembly Caution:
- Be aware of the risk of pinching or cuts during assembly.
- Do not confuse similar screws.
- Do not tighten bolts fully until all parts are connected.
The manufacturer declines all responsibility for damages due to improper installation or weather-related issues.
Usage Tips
- Ensure the chair is placed stably on a flat surface for optimal performance.
- Install the chair under a canopy or shelter.
- Keep the swing away from open flames.
- Avoid overloading the anchors/structure.
- Do not remain on the swing during storms.
- Cover the furniture when not in use, especially during adverse weather.
Maintenance and Storage
Maintenance:
- Clean the swing chair with a soft, damp cloth.
- Regularly remove leaves and/or water collected on the fabric.
- Periodically inspect the chair for any loose parts or damage.
- Do not use the product if the seat cloths, cushions, or tarpaulins are aged or deteriorated. Contact customer service if this is the case.
Storage Conditions:
- When not in use, store the furniture completely dry in a clean, dry place to avoid the risk of mold.
- Cover the furniture with an appropriate cover if stored outdoors.
Parts List
| Identifier | Description | Quantity |
|---|---|---|
| A | Top Bar | x01 |
| B | Side Frame | x02 |
| C | Curved Leg Support | x02 |
| D | Suspension Rod | x04 |
| E | Lower Support Bar | x02 |
| F | Lower Crossbar | x01 |
| G | Seat Frame | x02 |
| H | Canopy Support | x02 |
| J | Backrest Frame | x01 |
| K | Seat Cushion | x01 |
| L | Backrest Cushion | x01 |
| M | Canopy Fastener | x02 |
| Y | Canopy | x02 |
Hardware List
| Identifier | Description | Quantity |
|---|---|---|
| N | Washer/Tape | x04 |
| P | Bolt M8*110 | x04 |
| Q | Bolt M6*82 | x02 |
| R | Bolt M6*78 | x02 |
| S | Bolt M6*62 | x02 |
| T | Bolt M8*62 | x04 |
| U | Bolt M8*55 | x04 |
| V | Bolt M6*45 | x04 |
| W | Wrench | x01 |
| X | Screw | x02 |
Assembly Instructions
Note: Do not fully tighten bolts until assembly is complete.
Step 1: Assemble Main Frame Top
Connect the top bar (A) to the two side frames (B) using four M8*110 bolts (P).
Step 2: Attach Lower Support Bars
Attach the two lower support bars (E) to the inside of the side frames (B) using two M6*62 bolts (S).
Step 3: Connect Leg Supports to Crossbar
Connect the two curved leg supports (C) to the lower crossbar (F). Use two M6*82 bolts (Q) and two M6*78 bolts (R).
Step 4: Assemble Seat and Backrest Frames
Assemble the two seat frames (G) and the backrest frame (J). Use four M8*62 bolts (T) and four washers/tape (N).
Step 5: Attach Seat Assembly to Main Structure
Attach the assembled seat frames (G) to the main swing structure using four M6*45 bolts (V). Place the seat cushion (K) and backrest cushion (L) onto the assembled seat and backrest frames.
Step 6: Install Suspension Rods
Connect the swing seat assembly to the main frame using four suspension rods (D) and four M8*55 bolts (U).
Step 7: Attach Canopy Supports
Attach the two canopy supports (H) to the top bar (A) of the swing frame.
Step 8: Install Canopy
Attach the two canopies (Y) to the canopy supports (H) using the two canopy fasteners (M).
Assembly is now complete. Ensure all bolts are tightened securely.
Customer Service and Importer Information
For questions or assistance, please contact the importer in your region:
United States
Imported by Aosom LLC
27150 SW Kinsman Rd Wilsonville, OR 97070 USA
MADE IN CHINA
Canada
Imported by Aosom Canada Inc.
7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9
MADE IN CHINA
United Kingdom
IMPORTER ADDRESS: MH STAR UK LTD
Unit 27, Perivale Park, Horsenden lane South Perivale, UB6 7RH
MADE IN CHINA
France
ADRESSE D'IMPORTATION: MH FRANCE
2 Rue Maurice Hartmann 92130 Issy Les Moulineaux France
FABRIQUÉ EN CHINE
Spain & Portugal
IMPORTADOR: SPANISH AOSOM, S.L.
C/ROC GROS,N°15.08550, ELS HOSTALETS DE BALENYÀ, SPAIN.
B66295775
WWW.AOSOM.ES
ATENCIONCLIENTE@AOSOM.ES
TEL: 931294512
SPANISH AOSOM, S.L
C.ROC GROS N.15, 08550. ELS HOSTALETS DE BALENYÀ
TEL: 931294512 (SEG-SEX DAS 7:30H ÀS 16:30H)
INFO@AOSOM.PT
WWW.AOSOM.PT
Germany
ADRESSE DES IMPORTEURE: MH Handel GmbH
Wendenstraße 309 D-20537 Hamburg Germany
IN CHINA HERGESTELLT
Italy
IMPORTATO DA: AOSOM Italy srl
Centro Direzionale Milanofiori Strada 1 Palazzo F1 20057 Assago (MI)
P.I.: 08567220960
FATTO IN CINA
