EVO Nano Series Multi-channel Charger Guidelines

Autel Robotics

Disclaimer

Thank you for purchasing the EVO Nano™™ battery multi-channel charger. Please read this statement carefully before using this product. Use of this product signifies approval and acceptance of the entire content of this document. Use strictly according to this manual and pay attention to warnings.

Autel Robotics is not responsible for any damage or injury caused directly or indirectly by improper use of this product. This includes, but is not limited to, using an unauthorized charger, charging an unauthorized battery, short-circuiting, overheating, inserting foreign objects into the product, touching terminals with hands or metal. Please refer to the disclaimer, safe operation guide, quick start guide, and user manual for related information not covered in this article.

The copyright of this product and manual belongs to Autel Robotics, and all rights are reserved. Without the prior written consent or authorization of Autel Robotics, no part of this product and manual may be copied in any form.

⚠️ Warning:

Multi-charger is only applicable to the extended battery interface. Please use the EVO Nano standard power adapter to supply power for it.
Multi-charger is only applicable to EVO Nano series drone batteries. Do not use multi-charger to charge other types of batteries.
When using, please place the multi-charger steadily and pay attention to the insulation.
Do not touch the metal terminals with your hands or other objects.
If foreign matter is attached to the metal terminal, please wipe it with a dry cloth.

Product Introduction

The multi-charger can expand the battery interface to be multiple. It can be used with the EVO Nano standard adapter, which can connect up to 3 EVO Nano batteries for charging.

A diagram illustrates the multi-charger unit with three distinct battery slots. An arrow shows batteries being inserted into the primary battery port (labeled ①). The power input port is labeled ②.

Product Use

1. Connect the power supply

Connect the EVO Nano standard adapter to the power socket (100-240V), and then plug the charging connector into the power port of the multi-charger. After powering on, the LED indicator will light up, showing a blue light or a green light.

A diagram shows the Autel EVO Nano standard power adapter, a wall plug connected to a cable, which plugs into the multi-charger's power port.

2. Charge

Insert the aircraft battery into the battery port to start charging. Once inserted, the indicator light will begin to flash slowly. When all the batteries are fully charged, the indicator light will be off. Do not cover the charger during charging.

Product Features

Charge management

Sequence charging: Priority is given to charging the battery with the highest amount of power remaining, and when it reaches full charge, it will continue to charge the next battery with the highest power. In sequence charging mode, only one battery will be charged at a time.

Please unplug once the battery is fully charged.

Note: Inserting the battery may interrupt the battery being charged.

Specifications

Specification	Value
Operating Voltage	12V
Operating Temperature	5–45°C (41–113°F)
Reference Charging Time (3 Batteries)	4.5 hours

	EVO Lite Series Multi-channel Charger Guidelines This document provides guidelines for the EVO Lite Series multi-channel charger, detailing its product introduction, usage, features, and specifications. It covers charging management, operating voltage, temperature, and charging times.
	EVO Lite Series Multi-channel Charger Guidelines Official guidelines for the Autel Robotics EVO Lite Series Multi-channel Charger, detailing its features, safe usage instructions, and specifications for charging multiple EVO Lite drone batteries.
	Autel EVO II Series Battery Multi-charger Guidelines Comprehensive guidelines for the Autel EVO II Series battery multi-charger, covering product introduction, usage, charging modes, status indicators, and specifications.
	Autel EVO Nano Series Quick Start Guide A concise guide to getting started with the Autel EVO Nano series drone, covering aircraft and remote control setup, charging, app installation, and basic flight controls.
	Autel EVO II DUAL 640T Packing List Detailed packing list for the Autel EVO II DUAL 640T drone, outlining all included components such as aircraft, remote controller, propellers, batteries, chargers, and accessories.
	Autel EVO Nano Series Standard Package Packing List Detailed packing list for the Autel EVO Nano Series Standard Package drone, including all included components such as the aircraft, remote control, cables, and manuals.
	Autel EVO II Series Battery Safe Operation Guidelines Comprehensive safety, usage, charging, and storage guidelines for Autel EVO II Series drone batteries. Learn about battery protection features and specifications.
	Autel Robotics EVO II RTK Series Packing List Detailed packing list for the Autel Robotics EVO II RTK Series drone, outlining all included components and accessories.