Olight BALDR Mini User Manual

Introduction

Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!

In the Box

• BALDR Mini (with Battery)
• USB Magnetic Charging Cable
• Wrench
• 1913 Adapter and Screws
• NYLOK Cone Point Set Screw (for vertical calibration)
• NYLOK Oval Point Set Screw (for horizontal calibration)

Specifications

ℹ️ The green beam level is Class 3R, obeying the standard IEC60825-1 requirement.

ℹ️ All specifications are test results based on ANSI/NEMA FL1 Standard when the built-in battery is fully charged.

Product Overview

The BALDR Mini features the following components:

• Reflector and Green Beam Emitter
• Light Setting Switch (Controls green beam only, white LED/green beam combined, or white LED only)
• Switch (Ambidextrous, push-down activation)
• Magnetic Charging Port
• Low Battery Indicator (Turns red when battery is below 10%)
• Swing Arm (for mounting)
• Parallel Rail Adapter (pre-installed)
• "GL" Adapter (for Glock rails, pre-installed)
• 1913 Adapter (for Picatinny rails, included)
• Vertical Calibration Hole of Green Beam
• Horizontal Calibration Hole of Green Beam

Before First Use

Please fully charge the product before first use.

Connect the included USB magnetic charging cable to an external USB power source and attach it to the light's charging port. Charging takes approximately 1 hour. The charging indicator will be ? [Charging] while charging and turn ? [Charging Complete] when charging is finished.

Light Installation

The BALDR Mini can be mounted on Glock or Picatinny (MIL-STD-1913) rails.

1. Flip up the swing arm to unlock it.
2. Slide the light onto the rail mount.
3. Slide it back and forth to fix it in the desired position.
4. Flip down the swing arm to lock it securely.

Compatibility Check: The "GL" adapter is pre-installed for Glock rails. For Picatinny (MIL-STD-1913) rails, replace the "GL" adapter with the included 1913 adapter using the provided screws and wrench.

Green Beam Calibration

Use the included hex wrench to rotate the adjustment screws on the side of the light to calibrate the vertical or horizontal angle of the green beam for accurate aiming.

• The NYLOK cone point set screw is for vertical angle calibration.
• The NYLOK oval point set screw is for horizontal angle calibration.

Operation

The BALDR Mini offers three light settings, controlled by the Light Setting Switch:

• Green Beam Only: Move switch to the left.
• White LED / Green Beam Combined: Move switch to the middle.
• White LED Only: Move switch to the right.

The ambidextrous switches can only be activated by pushing downward. Pressing the side or front of the switch will not activate the light.

• Momentary ON: Press and hold down either switch. The light stays on until the switch is released.
• On/Off: Single-click either switch for constant on. Single-click again to turn the light off.

Safety Information

❗ DANGER

• DO NOT throw the light directly into human eyes. This may cause temporary blindness or permanent eye damage.
• DO NOT charge this product with charging cables other than the one included in the original package.
• DO NOT cover the light head, or place the light head down on the ground when the light is on. The radiation energy may cause damage to the light itself or result in burning other materials.
• DO NOT leave the light in fabric bags or fusible plastic containers under high temperatures.

⚠️ WARNING

• Keep out of reach of children.
• The green beam light is bright and blinding – DO NOT shine at aircraft or vehicles at any distance.
• If the light is stored or transported for a long time, turn the light setting switch to the Green Beam Only position.

ℹ️ NOTICE

• The setting switch is magnetically sensitive; proximity to magnets may cause interference.
• Fully charge the battery before storing the light for extended periods.
• Keep the charging port clean. Wipe off any dust before charging.
• Wipe the lens regularly. If the green beam spot appears abnormal, clean the lens.
• The LED light will operate at its top output mode for one minute, then gradually step down to 100 lumens within two minutes.
• The two switches are push-down activated only.
• Attaching the light to the rail helps protect the switch and prevents damage from falls.
• The BALDR Mini is only compatible with the included MCC special charging cable.
• NYLOK is a registered trademark of NYLOK LLC.

Warranty

• Within 30 days of purchase: Contact the original seller for repair or replacement.
• Within 2 years of purchase: Contact Olight for repair or replacement.

This warranty does not cover normal wear and tear, modifications, misuse, disintegration, negligence, accidents, improper maintenance, or repair by anyone other than an Authorized retailer or Olight itself.

Manufacturer Information

Dongguan Olight E-Commerce Technology Co., Ltd

Address: 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

Made in China

Support and More Information

USA Customer Support: cs@olightstore.com

Global Customer Support: customer-service@olightworld.com

Visit www.olightworld.com to see the complete product line.

EU-Declaration of Conformity can be found here: https://olightworld.com/ec-declaration