Olight BALDR RL User Manual

In the Box

• BALDR RL (with Battery)
• 1913 and Screw
• NYLOK Adjustable Screw
• Wrench

Specifications

* Results are based on tests using two 3V 1600mAh CR123A batteries and obey ANSI/NEMA FL1 standard.

* 1120 lumens is the output brightness when the battery is full. When battery power is lower than 30%, the maximum output brightness is limited to 500 lumens.

Product Overview

Before First Use

1. Pull up on the spring lock and open the tailcap.
2. Remove the insulating film from inside the battery compartment.
3. Close the tailcap.

Battery Installation

Safety Information

⚠️ DANGER

• DO NOT throw the light directly into human eyes. This may cause temporary blindness or permanent damage to the eyes.
• DO NOT cover the light head when the light is on, or place the light head on the ground. The radiation energy of the light may cause damage to the light itself, or even result in burning to other materials.
• DO NOT leave the light in any type of fabric bag or fusible plastic container under high temperature.

⚠️ WARNING

• Keep out of reach of children.
• After being on for a long time, the surface of the light may reach 50°C or higher. In this case, DO NOT touch the light to prevent burns.

? NOTICE

• Laser light is bright and blinding - DO NOT shine at aircraft or vehicles at any distance.
• If the light is stored for a long time or transported, turn the rotating switch to the Laser only position.
• When the light is on strobe mode and you change the light setting, it will quit strobe mode.
• Strobe mode is not available for the laser itself and only works when the mode selector is positioned to LED light only, and LIGHT&LASER combined.
• The light setting switch is sensitive to magnets and may malfunction when they are close.
• Pay attention to the battery polarities during installation. Signs for battery polarity are on the compartment cover.
• NOT compatible with RCR123 rechargeable lithium battery.
• The output will stay on 1120 lumens for 1 minute and step down to 500 lumens in 30 seconds.
• While battery power is too low, the maximum brightness will reach at 300 lumens.
• When batteries are running low, the light beam may blink, which is completely normal.
• NYLOK is a registered trademark of NYLOK LLC.

Operation

Three Light Settings Available: You can choose between LED light Only, Laser only, and LIGHT&LASER combined by flipping a rotating switch underneath the light. Brightness level changes and strobe mode are only available while using LED light only and LIGHT&LASER combined mode.

• CONSTANT ON/OFF: Single click either side switch for constant on. When the light is on, click either side switch again to turn it off.
• MOMENTARY ON: When the light is off, press and hold either side switch. Let go of the switch and it will turn off.
• CHANGE THE BRIGHTNESS LEVEL: When the light is on, quickly double click (or click three times or more) either side switch to change the brightness level. When the light is turned on again, it will return to the previously used brightness level.
• STROBE: Press both sides of the switch and release to enter strobe mode. Click either side switch to turn it off.

Light Installation

Light Settings

Compatibility Check

The BALDR RL can be used on most Glock or Picatinny (mil-std-1913) type rails. The Glock adapter labeled "GL" is already installed (compatible with most Glock handguns) and a Picatinny (mil-std-1913) adapter is included in the packaging. For Picatinny (mil-std-1913) rails, the user needs to replace the "GL" adapter with the included 1913 adapter using the screws and wrench provided in the package.

Laser Calibration

Use the included hex wrench to rotate the adjustment screw hole either underneath or on the side of the light to calibrate the vertical or horizontal angle of the laser beam, and finally sight in the laser for accurate use.

NOTE: A backup set of NYLOK adjustable screws is included.

Warranty

• Within 30 days of purchase: Contact the original seller for repair or replacement.
• Within 5 years of purchase: Contact Olight for repair or replacement.

This warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an Authorized retailer or Olight itself.

Contact & Compliance

EU-Declaration of Conformity: Can be found here: https://olightworld.com/ec-declaration

USA Customer Support: cs@olightstore.com

Global Customer Support: customer-service@olightworld.com

Visit www.olightworld.com to see our complete product line of portable illumination tools.

Manufacturer: Dongguan Olight E-Commerce Technology Co., Ltd

Address: 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

Made in China

Certifications: RoHS, CE

Date: B. 04, 23, 2020 | 3.0906.6010.9004