Olight BALDR Pro User Manual

In the Box

• BALDR Pro (with Battery)
• Wrench
• 1913 Adapter and Screw
• NYLOK Adjustable Screw

Specifications

Note on Performance: Results are based on tests using two 3V 1600mAh CR123A batteries, obeying ANSI/NEMA FL1 standard. The laser level is Class 3R, obeying IEC60825-1 requirement. The initial output is 1350 lumens, stepping down to 500 lumens after 1 minute (30 seconds for the step down). Maximum brightness is limited to 300 lumens when battery power is very low. Light beam may blink when batteries are running low.

NYLOK is a registered trademark of NYLOK LLC.

Product Overview

The BALDR Pro features several key components:

• TIR Optic Lens: For focused light output.
• Green Laser: For aiming.
• Parallel Rail Adapter: For mounting.
• Swing Arm: Allows for opening and closing the mount.
• "GL" Rail: The default Glock rail adapter.
• Mode Switch: Located underneath the light to select modes (LED only, Laser only, LED & Laser combined).
• Side Switch: Used for operation (ON/OFF, momentary, brightness adjustment, strobe).
• Vertical Calibration Hole of Laser: For adjusting the laser's vertical position.
• Horizontal Calibration Hole of Laser: For adjusting the laser's horizontal position.

Before First Use

Please open the tailcap as shown in the diagram. Remove the insulating film from the battery compartment and close the tailcap.

Diagram Description: Shows opening the tailcap by pulling up the spring lock, removing an insulating film, and then closing the tailcap.

Supported Battery

2 x CR123A batteries.

Battery Installation

1. Pull up on the spring lock and open the tailcap.
2. Place the batteries inside the body following the direction of the positive (+) and negative (-) marks indicated inside the compartment.
3. Hold the tailcap firmly and then close the spring lock.

Diagram Description: Illustrates the battery installation process with numbered steps and polarity indicators.

Light Installation

Open the swing arm as shown in the diagram. Ensure the rail insert used fits inside the rail notch without any movement. Close the swing arm once it is aligned.

Diagram Description: Shows how to open the swing arm, align it with a rail, and then close the swing arm to secure the light.

Compatibility Check

The BALDR Pro can be mounted on most Glock or Picatinny (mil-std-1913) type rails. The Glock adapter labelled "GL" is pre-installed and compatible with most Glock handguns. A Picatinny (mil-std-1913) adapter is included. For Picatinny rails, replace the "GL" adapter with the included 1913 adapter using the provided screws and wrench.

Laser Calibration

Use the included hex wrench to rotate the adjustment screw hole (located underneath or on the side of the light) to calibrate the vertical or horizontal angle of the laser beam for accurate aiming.

Note: A backup set of NYLOK adjustable screws is included.

Operation

Light Settings

Three light settings are available via the rotating switch located underneath the light:

• LED light Only
• Laser only
• LIGHT & LASER combined

Brightness level changes and strobe mode are only available when using LED light only and LIGHT & LASER combined modes.

Constant ON/OFF

Single click either side switch for constant ON. Click either side switch again to turn it OFF.

Momentary ON

When the light is OFF, press and hold either side switch. The light will turn OFF when the switch is released.

Change Brightness Level

When the light is ON, quickly double-click (or click three times or more) either side switch to cycle through brightness levels. The light will return to the previously used brightness level upon being turned on again.

Strobe Mode

Press both side switches simultaneously and release to enter strobe mode. Click either side switch to turn it OFF.

Important Safety Information

DANGER

• Do NOT throw the light directly into human eyes. This may cause temporary blindness or permanent eye damage.
• Do NOT cover the light head when the flashlight is on, or place the flashlight head on the ground. The heat generated may damage the flashlight or surrounding materials.
• Do NOT use rechargeable lithium batteries without a protection circuit, as this may lead to battery damage or hazardous situations.
• Do NOT leave the light in any type of fabric bag or fusible plastic container under high temperatures.

WARNING

• Keep out of reach of children.
• The surface of the light may reach 50°C (122°F) or higher after being on for 10 minutes or more. Avoid touching the light to prevent burns.
• Laser light is bright and blinding – DO NOT shine it at aircraft or vehicles at any distance.
• If the light is stored or transported for a long time, turn the rotating switch to the "Laser only" position.

NOTICE

• The light setting switch is sensitive to magnets and may malfunction if they are nearby.
• Pay attention to battery polarities during installation. Polarity indicators are present inside the battery compartment.
• The output will stay at 1350 lumens for 1 minute, then step down to 500 lumens over 30 seconds.
• When RCR123A batteries with a protection circuit are used, the light may experience sudden power failure due to the battery's protection mechanism (overcurrent or undervoltage protection).
• While battery power is very low, the maximum brightness will be limited to 300 lumens.
• When batteries are running low, the light beam may blink; this is normal.

Warranty

• Within 30 days of purchase: Contact the original seller for repair or replacement.
• Within 5 years of purchase: Contact Olight for repair or replacement.

This warranty does not cover normal wear and tear, modifications, misuse, disintegration, negligence, accidents, improper maintenance, or repair by anyone other than an authorized retailer or Olight itself.

Declarations and Support

EU-Declaration of Conformity can be found here: https://olightworld.com/ec-declaration

USA Customer Support: cs@olightstore.com

Global Customer Support: Customer-service@olightworld.com

Visit www.olightworld.com to see Olight's complete product line of portable illumination tools.

Manufacturer:

Dongguan Olight E-Commerce Technology Co., Ltd

Address: 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

Made in China