Amantii CUBE-2025WM Installation / Owner's Manual

Important Instructions

PLEASE RETAIN THIS USER GUIDE FOR FUTURE REFERENCE. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this fireplace.
2. The fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains at least 3 feet (0.91 m) from the front of the unit.
3. Extreme caution is necessary when any heater is used near children and whenever the unit is left operating and unattended.
4. Do not operate a fireplace with a damaged cord or plug, or if the heater has malfunctioned, the fireplace has drooped or damaged in any manner.
5. Not all fireplaces are suitable for use in bathrooms or laundry facilities. Please consult with individual product literature to confirm suitability.
6. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange the cord away from traffic area and where it will not be tripped over.
7. Do not modify this fireplace. Use it as described in the manual. Any other use not recommended by the manufacturer may cause fire, shock or injury to persons.
8. Do not use this heater with a programmer, timer, separate remote-control system or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
9. Disconnect all power supply before cleaning, maintenance or relocation of the fireplace.
10. Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust opening as this may cause electric shock, fire or damage to the heater.
11. Do not immerse the cord, plug or any part of the appliance in water or any other liquid.
12. In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device.

CAUTION: Procedures and techniques, which, if not carefully followed, will result in damage to the equipment.

WARNING: Procedures and techniques, which, if not carefully followed, will expose the user to the risk of fire, serious injury, illness or death.

Consult with a professional electrician and adhere to all code requirements for installations in bathrooms.

FCC Cautions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Unpacking and Testing the Appliance

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet. Test all aspects of its operation (manual switches, remote and heater) to make sure all components operate correctly. As with most electronic devices, your new electric fireplace has been designed to operate at temperatures between 5°C (41°F) and 35°C (95°F). During the cold winter months, allow the fireplace to reach room temperature before turning it on.

NOTE: There may be a trace of odor during the first few minutes of initial use. This is harmless, normal, and will never occur again.

Grounding the Appliance

This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as shown in (C) is available for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

To disconnect the appliance, turn controls to off, then remove plug from outlet.

Locating the Fireplace

Plan where to locate and frame the fireplace. This will save time and money later when you install the fireplace. Before installation, consider the following:

1. Where the fireplace is located must allow for wall and ceiling clearances.
2. Consider a location where the fireplace screen will not be exposed to direct sunlight from windows or doors.
3. A 15 ampere, 120 Volt, 60 Hz branch circuit with proper ground must be available at the location. Preferably, a dedicated branch circuit should be provided to avoid circuit breakers tripping or fuses blowing.

CUBE-2025WM Specifications

This appliance has been tested in accordance with the UL Standard 2021 for fixed and location dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer.

NOTE: This appliance must be electrically wired and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA 70 National Electrical Code in the United States.

Installation Wall-Mount

NOTE: Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance.

1. Select a location that is not prone to moisture and is located at least 0.91 m or 3 feet away from combustible materials such as curtains or drapes, furniture, bedding, paper, etc.
2. Select a suitable position in which to mount the heater horizontally; use a spirit level to achieve this. (Illustration shows a spirit level used to ensure the heater is mounted horizontally.)
3. Check the wall to ensure there are no wiring, pipe wires etc. in the area to be drilled. Drill 8 or more pilot holes (8mm diameter & 40mm depth) using a suitable size drill and put the wall plugs into the holes.
4. Take out the hanger from the fireplace by unscrewing the screw. (Diagram shows the removal of a screw to detach the hanger from the fireplace.)
5. Fix the hanger to the wall. (Illustration shows the hanger being fixed to the wall.)
6. To prevent the fireplace from moving, use screws to fix the fireplace to the wall. (Diagram shows screws used to secure the fireplace to the wall.) Warning! Be sure that the bolts have been fixed firmly enough to withstand the weight.

Installation Cube-Base-Legs

1. Screw the base legs to the steel panel. (Illustration shows base legs being screwed into the steel panel.)
2. Unscrew the adjustable feet from the bottom of the unit. (Illustration shows adjustable feet being unscrewed from the bottom of the unit.)
3. Place the unit onto the base leg and screw in the adjustable feet, fixing the unit and the base leg. (Illustration shows the unit placed on the base leg and adjustable feet being screwed in to fix it.)
4. You have completed the installation of the CUBE-BASE-LEGS.

Installation Cube-Base-Speaker

1. Unscrew the adjustable feet from the unit. (Illustration shows adjustable feet being unscrewed from the unit.)
2. Unscrew the rear screws and remove the back steel panel. (Illustration shows rear screws being removed to detach the back steel panel.)
3. Place the unit on the CUBE-BASE-SPEAKER and screw in the adjustable feet, fixing the unit and the speaker box. (Illustration shows the unit placed on the CUBE-BASE-SPEAKER and adjustable feet screwed in.)
4. Plug into the back of the unit. Re-install the back steel panel. (Illustration shows the power cord being plugged into the back of the unit and the back steel panel being re-installed.)

Installation Outdoor

The Cube (CUBE-2025WM) is suitable for installation in outdoor areas protected from direct water impingement. In addition to maintaining the listed mantel and combustibles clearances, a rain protection overhang factor of 1/2 shall be constructed to the front and to each side of the installed appliance. See illustration below.

All wiring connections to line power shall be in accordance with local building code requirements.

NOTE: The CUBE Wall Mount Unit is approved for outdoor use. The Cube Speaker Base and Cube Leg Base are NOT approved for use outdoors.

The overhang (A) must extend at least 1/2 the roof-line height (B). Height is measured from the base of the fireplace. For example: if the roof-line (B) is 8' above the base of the fireplace, the overhang (A) must be at least 4'. (Diagram shows an outdoor installation with a protective overhang (A) extending at least half the roof-line height (B) from the base of the fireplace.)

Hardwire Installation

Turn off the appliance completely and let cool before servicing. Only a qualified technician should service and repair this electric appliance. If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection and wire the appliance directly to the household wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

1. Remove the cover plate from the left side of the appliance by removing the two screws, as shown below. Unscrew and remove power cord. (Illustration shows the removal of the cover plate from the left side of the appliance, followed by unscrewing and removing the power cord.)
2. Attach the wiring to the junction block. Please make sure the live wire goes into "L", the neutral wire into "N", and the ground wire into "G". (Illustration shows wiring connections to a junction block, with labels for "L" (live), "N" (neutral), and "G" (ground).)
3. Replace the steel plate and screws.

Media Options

The media that come with this appliance are Birch Log Set, "Clear glass", Amber glass, one (1) bag of Black Vermiculite, and one (1) bag of White Vermiculite. Consumers may purchase optional decorative media if they choose. See dealer for more details.

Decorative Media Installation

1. Unplug the unit and make sure controls are switched off.
2. Unscrew the 2 adjustable screws that securing the front glass panel. (Always secure the front glass before unscrewing the securing screws; removal of the securing screws may cause the front glass to fall out suddenly.)
3. Remove the front glass panel to decorate your fireplace. Pour the decorative media into the tray. Feel free to use any combination of fire glass media that you find most appealing.
4. After finishing decoration, re-install the front glass panel using the securing screws removed in step 2.

Operation

The Fireplace operates by using either the touch panel located on the upper left-hand corner or by remote control. Plug the fireplace into a 15 Amp wall socket.

Manual Operation

1. Press the [Power Button] to turn on and off the fireplace.
2. Press the [Flame Brightness Button] to adjust the flame's brightness. There are 7 brightness levels (L5 L4 - L3 L2 L1 L0 L6). The indicator light turns off automatically after 10 seconds of inactivity.
3. Press the [Ember Bed Brightness Button] to adjust the ember bed brightness. There are 12 brightness levels (D4 D5 D6 D7 D8 D9 DA DB D0 D1 D2 D3).
4. Press the [Timer Button] to set the turn-off time (30min-1h-2h-3h-4h-5h-6h-7h-8h-t0). The indicator light turns off automatically after 10 seconds of inactivity. The timing turns off when the [Power Button] is pressed.
5. Press the [Heater Auto Mode Button] to turn on and off the heater in its AUTO mode. The setting temperature switches through Fahrenheit: 59- 61- 63- 64- 66- 68- 70- 72- 73- 75- 77- 79- 81- 83; or Celsius: 15 -16 -17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28. The temperature setting mode will close automatically if left inactive for 5 seconds.
6. When the heater is on, press and hold the [Temperature Unit Switch Button] for 5 seconds to switch between Celsius and Fahrenheit.

Remote Control Operation

For the remote to function, make sure the fireplace is plugged in and the remote has batteries. Important: When operating the remote, make sure you point the remote to the center of the fireplace. Each time you press a button, the buzzer inside the unit will beep once. It takes some time for the receiver to respond to the transmitter. Do not press the buttons more than once within two seconds for correct operation.

Set the current time of the remote control

Press the [Time/Date Button] to activate the remote control and press the [Time/Date Button] again to set the time and date. When one of the days "Sun" "Mon" "Tue" "Wed" "Thu" "Fri" "Sat" is flashing, press the [Hour/Minute Adjust Button] or [Day Select Button] to set the day of the week, then press the [Confirm Button] to confirm the day of the week and enter hour setting. Press the [Hour/Minute Adjust Button] to set the hour, press the [Confirm Button] to confirm the hour and then enter minute setting. Press the [Hour/Minute Adjust Button] to set the minute and press the [Confirm Button] to confirm the minute and finish time setting.

Power

Press this [Power Button] to turn on and off the fireplace.

Timer

Press this [Timer Button] to set the time to turn off the fireplace. The available settings range from 30 minutes to 8 hours (0:30 - 1:00 - 1:30 - 2:00 - 2:30 - 3:00 - 3:30 - 4:00 - 4:30 - 5:00 - 5:30 - 6:00 - 6:30 - 7:00 - 7:30 - 8:00). Once you have set the timer, the [Timer Icon] will be displayed on the LCD screen of the remote control. Press this button again to cancel the timer setting and the [Timer Icon] disappears.

Heater

Press the [Heater Button] once: one setting of heater works, 750W, indicating "H 1" on display. Press again: two settings of heater work, 1500W, indicating "H 2" on display. Press for the third time to turn on the AUTO mode. Press the [Temperature Adjust Button] or [Temperature Unit Switch Button] to set the temperature and switch the temperature unit between Celsius and Fahrenheit.

Flame Speed

Press this [Flame Speed Button] to adjust the speed of the flame. There are 3 options: High, Medium, Low.

Ember Bed Light

Press this [Ember Bed Light Button] to turn on and off the ember bed light. When in ON position, the display screen of the remote control shows AD 1. When the number "1" flashes, you can set the color of the ember bed by the [Color Select Button] or [Color Cycle Button]. There are 10 different ember bed light colors (AD1-10). When in AD 11 status, the color of the ember bed light cycles through 10 colors. Press [SET Button] to confirm the setting.

Flame

Press the [Flame Button] to turn on and off the Flame. When in ON position, the LCD screen of the remote control shows 666. Press the [Color Brightness Adjust Button] or [Color Brightness Cycle Button] to change the brightness of each color flame.

7 Day Timer Function

Press the [7 Day Timer Button] once: 7 days from Monday to Sunday will display on the LCD screen of the remote control. Press the [7 Day Timer Button] within 5 seconds to enter the 7-day timer function. When "Sun" flashes, press the [Day Select Button] or [Day Adjust Button] to select the day that you want to set, then press the [Confirm Button] to confirm your setting. Then "ON" will be displayed on the LCD screen of the remote control, at the same time, the digital hour flashes. Press the [Hour Adjust Button] or [Minute Adjust Button] to set the time to turn the fireplace on. After setting the startup time, "OFF" will be displayed on the LCD screen, and press the [Hour Adjust Button] or [Minute Adjust Button] to set the shutdown time. When the shutdown time is set, "AUTO" will be displayed on the LCD screen of the remote control, and the digital temperature flashes. At this time, you can set the temperature by the [Temperature Adjust Button] or [Temperature Unit Switch Button]. Now, you have finished setting of this function.

When the 7-day timer is set, the [7-Day Timer Icon] will be displayed on the LCD screen of the remote control. Press the [7 Day Timer Button] again to cancel the 7-day timer, and the [7-Day Timer Icon] will disappear.

NOTE: If the 7-day timing and the general timing are set at the same time, the system will respond to an earlier shutdown time.

Refer Button

Press the [Refer Button] to check the settings of the 7-day timer. Press the [Day Select Button] or [Day Adjust Button] to see the settings of the day of the week, and the [Time/Date Button] or [Time Adjust Button] for the settings of the startup and shutdown time.

Wi-Fi Operation

Install TuyaSmart life

There are 2 ways to install TuyaSmart: 1. Search for "TuyaSmart life" in the APP store on your phone, download and install. 2. Scan the QR code below with your mobile phone.

Wi-Fi Setting and Fireplace Operation

1. Create an account and log in.
2. When you log in, touch "+" (FIG.1) to enter the device list (FIG.2). Touch "Others" on the left corner first and then choose "Connector (Wi-Fi)" to enter the Wi-Fi setup screen (FIG.3) to set your Wi-Fi account and password.
3. Press and hold the [Flame Button] on the touch panel of the fireplace for more than 5 seconds when the fireplace is in standby mode. There will be 2 beeps from the fireplace, and the [Flame Button] will flash, indicating that Wi-Fi is in EZ mode. Then, please confirm to go next in the app (FIG.5).
4. The APP will scan (FIG.6) and add the fireplace to the APP (FIG.7) automatically. Please make sure the Wi-Fi account and password you entered are correct and the Wi-Fi signal is good.
5. Touch "Done" to finish Wi-Fi setting (FIG.7).
6. Now you are in the interface like FIG.7. You can operate the fireplace via Wi-Fi.

Replacement Parts

*Remote Control & WiFI Card are not shown in the exploded view.

*Items may not appear exactly as illustrated.

Model numbers: WM-BI-2428 VLR -BG - WiFi, 10124129, 602082, 601097, 601139B, 10104010, 301506, 10103007, 10124003, 3056504E, 601144, 601144, 3056503D, 10701200C, 10702150, 10701164, 10101501, 212051.

Exploded View

The exploded view diagram shows the assembly of the CUBE-2025WM fireplace, illustrating the arrangement of components such as the top panel, back top panel, circuit board, blower and heater assembly, fireplace box, canopy light, signal receiver, power cord, touch panel, flicker assemblies, LED strips, tray glass, side bracket, and front flat glass. The remote control and WiFi card are separate accessories.

Wiring Diagram

The wiring diagram illustrates the electrical connections within the CUBE-2025WM fireplace. It details the flow of power from the input source through the circuit board to various components including the heater, blower, flame flicker assembly, LED strips for the flame and ember bed, and the signal receiver for remote and Wi-Fi control. Proper grounding and connection to the junction block are also depicted.

Troubleshooting

Service History

This heater must be serviced annually depending on usage.

NOTES:

Warranty

Amantii Imports Corp. ("Amantii") warrants that your newly purchased Amantii electric fireplace is free from manufacturing and material defects for a period of two (2) years from the date of the first purchase, subject to the conditions and limitations contained below.

Warranty Application & Exclusions

This limited warranty applies to your newly purchased Amantii electric fireplace; its application is limited to purchases made in any province of Canada or in any of the 52 States of the United States of America, including the District of Columbia. Only the original purchaser of the product is eligible for coverage under this limited warranty; the warranty is not transferable.

Products excluded from this limited warranty: Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner/purchaser. Amantii does not cover service or labor charges.

Warranty Coverage and Term

Products covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Amantii warrants such products to be free from defects in material and workmanship for a period of two (2) years from the date of the first purchase of such products. The limited two (2) year warranty period also applies to any implied warranties that may exist under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to the purchaser. All other warranties—expressed or implied—with respect to the product, its components and accessories, or any obligation/liabilities on the part of Amantii are hereby expressly excluded.

Limitations to Coverage Under Limited Warranty

This limited warranty does not apply to products that have been repaired, except by Amantii or its authorized service representatives, or otherwise altered. This limited warranty further does not apply to defects resulting from misuse, abuse, accident, neglect, incorrect installation, improper maintenance or handling, or operation with an incorrect power source. Products made by other manufacturers, sold with the product or thereafter, are not covered by this limited warranty. The use of unauthorized components will render this warranty null and void.

Panorama Outdoor Units

All Panorama units that are installed outdoors or in moisture-intense conditions must use the stainless steel cover. Proof of purchase of the cover is required for any warranty claims.

Defects

Defects must be brought to the attention of the selling dealer. Please have your proof of purchase, catalogue/model, and serial numbers available when contacting the dealer; any and all service under the limited warranty requires a proof of purchase of the product. Should a product or part covered by this limited warranty be proven to be defective, in material or workmanship, and during the two (2) year limited warranty period, Amantii will replace such defective product or part without charge. If Amantii is unable to replace such product, or if replacement is not commercially practicable or cannot be timely done, in its sole discretion Amantii may, in lieu of replacement, choose to refund the purchase price for such product or part. Amantii does not cover labor or service charges to replace said parts.

Limitations

In no event will Amantii be liable to the purchaser or any third party for any indirect, special, punitive, exemplary, consequential, or incidental loss, cost, or damage arising out of or in connection with the sale, maintenance, use, or inability to use the product, even if Amantii has been advised of the possibility of such losses, costs, or damages, or if such losses, costs, or damages are foreseeable. In no event will Amantii be liable for any direct losses, costs, or damages that exceed the purchase price of the product. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to the purchaser.

Application of Provincial and State Law

This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty.

Amantii reserves the right to make changes at any time without notice, in design, material, specifications, prices, and the right to discontinue styles and products.

Amantii Electric Fireplaces, 502-1027 Davie Street, Vancouver, BC V6E 4L2