Amantii CUBE-2025WM Installation / Owner's Manual

Important Instructions

Please Retain This User Guide for Future Reference

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this fireplace.
2. The fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains at least 3 feet (0.91 m) from the front of the unit.
3. Extreme caution is necessary when any heater is used near children and whenever the unit is left operating and unattended.
4. Do not operate a fireplace with a damaged cord or plug, or if the heater has malfunctioned, or the fireplace has drooped or been damaged in any manner.
5. Not all fireplaces are suitable for use in bathrooms or laundry facilities. Please consult individual product literature to confirm suitability.
6. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from traffic areas and where it will not be tripped over.
7. Do not modify this fireplace. Use it as described in the manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
8. Do not use this heater with a programmer, timer, separate remote-control system, or any other device that switches the heater on automatically, as a fire risk exists if the heater is covered or positioned incorrectly.
9. Disconnect all power supply before cleaning, maintenance, or relocation of the fireplace.
10. Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust opening, as this may cause electric shock, fire, or damage to the heater.
11. Do not immerse the cord, plug, or any part of the appliance in water or any other liquid.
12. In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device.

SAVE THESE INSTRUCTIONS

Caution: Procedures and techniques, which, if not carefully followed, will result in damage to the equipment.

Warning: Procedures and techniques, which, if not carefully followed, will expose the user to the risk of fire, serious injury, illness or death.

Consult with a professional electrician and adhere to all code requirements for installations in bathrooms.

FCC Cautions

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Unpacking and Testing the Appliance

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet. Test all aspects of its operation (manual switches, remote, and heater) to make sure all components operate correctly.

As with most electronic devices, your new electric fireplace has been designed to operate at temperatures between 5°C (41°F) and 35°C (95°F). During the cold winter months, allow the fireplace to reach room temperature before turning it on.

Note: There may be a trace of odor during the first few minutes of initial use. This is harmless, normal, and will never occur again.

Grounding the Appliance

This appliance is for use on 120 Volts. The cord has a plug as shown in [Figure A]. An adapter [Figure C] is available for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground, such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

To disconnect the appliance, turn controls to OFF, then remove the plug from the outlet.

Note: Adapters are NOT for use in Canada.

Locating the Fireplace

Plan where to locate and frame the fireplace. This will save time and money later when you install the fireplace. Before installation, consider the following:

1. Where the fireplace is located must allow for wall and ceiling clearances.
2. Consider a location where the fireplace screen will not be exposed to direct sunlight from windows or doors.
3. A 15 Amp, 120 Volt, 60 Hz branch circuit with proper ground must be available at the location. Preferably, a dedicated branch circuit should be provided to avoid circuit breakers tripping or fuses blowing.

CUBE-2025WM Specifications

This appliance has been tested in accordance with the UL Standard 2021 for fixed and location-dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer.

Note: This appliance must be electrically wired and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the current ANSI/NFPA 70 National Electrical Code in the United States.

Installation: Wall Mount

Note: Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance.

1. Select a location that is not prone to moisture and is located at least 0.91 m (3 feet) away from combustible materials such as curtains or drapes, furniture, bedding, paper, etc.
2. Select a suitable position in which to mount the heater horizontally. Use a spirit level to achieve this [Figure 1].
3. Check the wall to ensure there is no wiring, pipes, etc. in the area to be drilled. Drill 8 or more pilot holes (8mm diameter & 40mm depth) using a suitable size drill bit and insert the wall plugs into the holes.
4. Take out the hanger from the fireplace by unscrewing the screw [Figure 2].
5. Fix the hanger to the wall, referring to [Figure 3].
6. To prevent the fireplace from moving, use screws to fix the fireplace to the wall [Figure 4].

Warning! Be sure that the bolts have been fixed firmly enough to withstand the weight.

Installation: Cube-Base Legs

1. Screw the base legs to the steel panel.
2. Unscrew the adjustable feet from the bottom of the unit.
3. Place the unit onto the base legs and screw in the adjustable feet, fixing the unit and the base legs.
4. You have completed the installation of the CUBE-BASE-LEGS.

Installation: Cube-Base Speaker

1. Unscrew the adjustable feet from the unit.
2. Unscrew the rear screws and remove the back steel panel.
3. Place the unit on the CUBE-BASE-SPEAKER and screw in the adjustable feet, fixing the unit and the speaker box.
4. Plug into the back of the unit. Re-install the back steel panel.

Installation: Outdoor

CUBE electric fireplaces are suitable for installation in outdoor areas protected from direct water impingement. In addition to maintaining the listed mantel and combustible clearances, a rain protection overhang factor of 1/2 shall be constructed to the front and to each side of the installed appliance. See illustration below.

All wiring connections to line power shall be in accordance with local building code requirements.

Note: The CUBE Wall Mount Unit is approved for outdoor use. The Cube Speaker Base and Cube Leg Base are NOT approved for use outdoors.

The overhang (A) must extend at least 1/2 the roof-line height (B). Height is measured from the base of the fireplace. For example: if the roof-line (B) is 8' above the base of the fireplace, the overhang (A) must be at least 4'.

Mantel Clearance

The clearance to the mantel should be 6 inches (15.2 cm) minimum when a mantel is applied (Measurement is taken from the glass front).

Diagram shows a wall with combustible facing allowed, a fireplace, a mantel, and the floor, with a 6" clearance indicated between the mantel and the fireplace.

Hardwire Installation

Turn off the appliance completely and let it cool before servicing. Only a qualified technician should service and repair this electric appliance. If it is necessary to hardwire this appliance, a qualified electrician must remove the cord connection and wire the appliance directly to the household wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hardwired. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

1. Remove the cover plate from the left side of the appliance by removing the two screws, as shown below. Unscrew and remove the power cord.
2. Attach the wiring to the junction block. Please make sure the live wire goes into "L" (Live), the neutral wire into "N" (Neutral), and the ground wire into "G" (Ground).
3. Replace the steel plate and screws.

Media Options

The media that come with this appliance are Birch Log Set, "Clear glass", Amber glass, one (1) bag of Black Vermiculite, and one (1) bag of White Vermiculite. Consumers may purchase optional decorative media if they choose. See dealer for more details.

Decorative Media Installation

1. Unplug the unit and make sure controls are switched off.
2. Unscrew the 2 adjustable screws securing the front glass panel. (Always secure the front glass before unscrewing the securing screws; removal of the securing screws may cause the front glass to fall out suddenly).
3. Remove the front glass panel to decorate your fireplace. Pour the decorative media into the tray. Feel free to use any combination of fire glass media that you find most appealing.
4. After finishing decoration, re-install the front glass panel using the securing screws removed in step 2.

Operation

The fireplace operates by using either the touch panel located on the upper left-hand corner or by remote control. Plug the fireplace into a 15 Amp wall socket.

Manual Operation

1. Press [Power Button Symbol] to turn the fireplace on and off.
2. Press [Flame Brightness Button Symbol] to adjust the flame brightness. There are 6 brightness levels (L6-L1) and an OFF (OF) position. Each time the flame button is pressed, the brightness of the flame decreases. Press the flame button for 10 seconds: the timing indicator light will turn on and blink rapidly. At this time, you can use the TuyaSmart APP to connect to the fireplace.
3. Press [Ember Bed/Moodlight Brightness Button Symbol] to adjust the ember bed / moodlight brightness. There are 11 brightness levels (d11-d2), a dynamic condition (d1), and the OFF (OF) setting you can cycle through.
4. Press [Timer Button Symbol] to set the turn-off time. Options include 30 min, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h, t0. The indicator light shows the current timing. If the timing is in the OFF position, the second press will show 30 min. Multiple presses set the operating duration to OFF, 30 min, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h.
5. Press [Temperature Button Symbol] for the first time to display the current setting temperature. Press the button again to clear the current temperature. If the heater is in the OFF position, the second press will show 22°C (72°F). Multiple presses set ambient temperatures at 22°C (72°F), 23°C (74°F), 24°C (76°F), 25°C (78°F), 26°C (80°F), 27°C (82°F), 28°C (84°F), 15°C (52°F), 16°C (54°F), 17°C (56°F), 18°C (58°F), 19°C (60°F), 20°C (62°F), 21°C (64°F).

Temperature unit conversion function: When the heater is on, press and hold the [Temperature Button Symbol] for 5 seconds; the current temperature unit display will convert to another temperature unit.

Remote Control Operation

For the remote to function, make sure the fireplace is plugged in and the remote has batteries. Important: When operating the remote, make sure you point the remote towards the center of the fireplace. Each time you press a button, the buzzer inside the unit will beep once. It takes some time for the receiver to respond to the transmitter. Do not press the buttons more than once within two seconds for correct operation.

• Set the current time: Press the [Time Set Button Symbol] to activate the remote control and press [Up/Down Arrow Buttons Symbol] to set the time and date. When one of the days "Sun", "Mon", "Tue", "Wed", "Thu", "Fri", "Sat" is flashing, press [Up/Down Arrow Buttons Symbol] to set the day of the week, then press [Confirm Button Symbol] to confirm the day of the week and enter hour setting. Press [Up/Down Arrow Buttons Symbol] to set the hour, press [Confirm Button Symbol] to confirm the hour and then enter minute setting. Press [Up/Down Arrow Buttons Symbol] to set the minute and press [Confirm Button Symbol] to confirm the minute and finish time setting.
• Power Button: Press this button to turn the fireplace on and off.
• Timer Button: Press this button to set the time to turn off the fireplace. The available settings range from 30 minutes to 8 hours (e.g., 0:30, 1:00, 1:30, ..., 8:00). Once you have set the timer, the [Timer Icon Symbol] will be displayed on the LCD screen of the remote control. Press this button again to cancel the timer setting, and the icon disappears.
• Heater Button: Each time the Heater Button is pressed, the power of the heater will change. Options are H1 (Low Heat / 750W), H2 (High Heat / 1500W), AUTO (fireplace can automatically adjust to the temperature you set), and OFF (no display). When in AUTO mode, you can set the desired temperature with the [Up/Down Arrow Buttons Symbol]. You can switch temperature between Celsius and Fahrenheit with the [Up/Down Arrow Buttons Symbol]. When on Auto mode, the fireplace operates at 1500W.
• Flame Speed Button: Press this button to adjust the speed of the flame. There are 3 options: High, Medium, Low.
• Ember bed / Moodlight Button: This button turns the ember bed or moodlight on and off. When in the ON position, the display screen of the remote control shows "AD1". When the number "1" flashes, you can set the color with the [Up/Down Arrow Buttons Symbol]. There are 10 different colors (AD1-AD10) and a dynamic condition (AD11) to choose from.
• Flame Button: Press the Flame button to turn the flame on and off. When in the ON position, the LCD screen of the remote control shows "6 6 6". Press the [Up/Down Arrow Buttons Symbol] to change the brightness of each color flame.
• 7-Day Timer Function: Press once. 7 days from Monday to Sunday will display on the LCD screen of the remote control. Press within 5 seconds to enter the 7-day timer function. When "Sun" flashes, press [Up/Down Arrow Buttons Symbol] to select the day you want to set, then press [Confirm Button Symbol] to confirm your setting. Then "ON" will be displayed on the LCD screen of the remote control, and at the same time, the hour digits flash. Press [Up/Down Arrow Buttons Symbol] to set the time to turn the fireplace ON. After setting the startup time, "OFF" will be displayed on the LCD screen, and press [Up/Down Arrow Buttons Symbol] to set the shutdown time. When the shutdown time is set, "AUTO" will be displayed on the LCD screen, and the temperature digits flash. At this time, you can set the temperature using the [Up/Down Arrow Buttons Symbol]. Now you have finished setting this function.

When the 7-day timer is set, the [7-Day Timer Icon Symbol] will be displayed on the LCD screen of the remote control. Press the button again to cancel the 7-day timer, and the icon will disappear.

Note: If the 7-day timing and the general timing are set at the same time, the system will respond to the earlier shutdown time.

• Refer Button: Press this button to check the settings of the 7-day timer. Press [Up/Down Arrow Buttons Symbol] to see the settings of the day of the week and [Up/Down Arrow Buttons Symbol] for the settings of the startup and shutdown time.

WiFi Operation

Install TuyaSmart life

There are 2 ways to install TuyaSmart:

1. Search for "TuyaSmart life" in the App Store on your phone, download and install.
2. Scan the QR code below with your mobile phone.

Wi-Fi Setting and Fireplace Operation

1. Create an account and log in.
2. When you log in, touch "+" [Figure 1] to enter the screen shown in [Figure 2]. Touch "Others" on the left corner first, and then choose "Connector (Wi-Fi)" to enter the screen shown in [Figure 3] to set your Wi-Fi account and password.
3. Press the [Flame Button Symbol] on the touch panel of the fireplace for more than 5 seconds when the fireplace is in standby mode. There will be 2 beeps from the fireplace, and the [Flame Button Symbol] will flash, indicating that Wi-Fi is in EZ mode. Then, please confirm to proceed [Figure 5].
4. The app will scan [Figure 6] and add the fireplace to the app [Figure 7] automatically. Please make sure the Wi-Fi account and password you set are correct and the Wi-Fi signal is good.
5. Touch "Done" to finish Wi-Fi setting [Figure 7].
6. Now you are in an interface like [Figure 7]. You can operate the fireplace via Wi-Fi.

Note: Turn off the flashing blue Wi-Fi indicator light. Touch the [Power Button Symbol] once; the blue light will stop flashing.

Replacement Parts

There is a QR code indicated by the arrow in the below image (The QR code is on the left top behind the front glass). Scan the code to get the replacement parts list for your reference. You will get a detailed parts list with images.

*There is a QR code on page 2 of the manual, at the bottom of the table of contents.

Exploded View

A diagram showing all components of the fireplace disassembled with labels indicating each part.

Troubleshooting

Service History

This heater requires annual servicing depending on usage.

Date | Dealer Name | Service Technician Name | Service Performed | Special Concerns | Notes

(Space for recording service history)

Warranty

Electric Fireplace Warranty

For Products Manufactured After January 1, 2016

Amantii Imports Corp. ("Amantii") warrants that your newly purchased Amantii electric fireplace is free from manufacturing and material defects for a period of two (2) years from the date of the first purchase, subject to the conditions and limitations outlined below.

Warranty Application & Exclusions

The limited warranty applies to purchases made in any province of Canada or any of the 52 States of the United States of America, including the District of Columbia. Only the original purchaser of the product is eligible for coverage under this limited warranty; the warranty is not transferable.

Products Excluded from This Limited Warranty

Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner/purchaser.

Warranty Coverage and Term

Products covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Amantii warrants such products to be free from defects in material and workmanship for a period of two (2) years from the date of the first purchase of such products.

The limited two (2) year warranty period for products also applies to any implied warranties that may exist under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to the purchaser.

All other warranties, expressed or implied, regarding the product, its components, and accessories, or any obligations/liabilities on the part of Amantii, are hereby expressly excluded.

Warranty Coverage and Term - Bespoke Series

Products covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Amantii warrants such products to be free from defects in material and workmanship for a period of five (5) years from the date of the first purchase of such products.

The limited five (5) year warranty period for products also applies to any implied warranties that may exist under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to the purchaser.

All other warranties, expressed or implied, regarding the product, its components, and accessories, or any obligations/liabilities on the part of Amantii, are hereby expressly excluded.

Limitations to Coverage Under Limited Warranty

This limited warranty does not apply to products that have been repaired (except by Amantii or its authorized service representatives) or otherwise altered. This limited warranty further does not apply to defects resulting from misuse, abuse, accident, neglect, incorrect installation, improper maintenance or handling, or operation with an incorrect power source. Products made by other manufacturers, sold with the product or thereafter, are not covered by this limited warranty. The use of unauthorized components will render this warranty null and void.

Panorama Outdoor Units

All Panorama units that are installed outdoors or in moisture-intense conditions must use the stainless steel cover. Proof of purchase of the cover is required for any warranty claims.

Service Under Limited Warranty

Defects must be brought to the attention of Amantii Technical Support by contacting Amantii at 1-877-850-9458, or at 502-1027 Davie Street, Vancouver, BC V6E 4L2. Please have your proof of purchase, catalogue/model, and serial numbers available when calling; all service under the limited warranty requires proof of purchase of the product.

Defects

Should a product or part covered by this limited warranty be proven defective in material or workmanship during the two (2) year limited warranty period, Amantii will replace such defective product or part without charge. If Amantii is unable to replace the product, or if replacement is not commercially practicable or cannot be done in a timely manner, Amantii may, at its sole discretion, refund the purchase price for such product or part instead of replacement.

Application of Provincial and State Law

This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty.

General

Amantii reserves the right to make changes at any time without notice to design, materials, specifications, prices, and the right to discontinue styles and products.

Glass

This limited warranty does not apply to the following glass products:

Exclusion of Batteries

Ocean carriers have implemented new rules to protect the safety of shipments during transit. This new rule disallows the inclusion of lithium/alkaline batteries; batteries will no longer be included with the fireplace remote.

Replacement Motors

With the reliability of the components used in the construction of electric fireplaces, a complimentary replacement motor will no longer be included in the fireplace carton.

Technical Support: 1-877-850-9458 - Ext 5

Customer Service: 1-877-850-9458 - Ext 1

Or email: cdn-service@amantii.com

www.amantii.com

Revised - 01.01.22AC