Oase Waterfall Pump 1650 / 2300

Operating Instructions

Reminder

CALL 1-866-627-3435 BEFORE RETURNING TO STORE.

Part	Description	QTY
A	Pump	1
B	1 in. and 1½ in. ID tubing adapter	1

Diagram Description: The document shows a diagram of the Oase Waterfall Pump (labeled A) and a separate tubing adapter (labeled B).

Information about these operating instructions

Welcome to OASE Living Water. You made a great choice with the purchase of this product Waterfall Pump 1650 / 2300. Prior to operating the unit, please read the instructions of use carefully and fully familiarize yourself with the unit. Ensure that all work on and with this unit is only carried out in accordance with these instructions. Please strictly follow the enclosed instructions to ensure safe and correct handling of the product. Keep these instructions in a safe place. Please also hand over the instructions when passing the unit on to a new owner.

Warnings and Cautions Symbols

The symbols used in this operating manual have the following meanings:

⚡ Risk of injury to persons due to dangerous electrical voltage. This symbol indicates an imminent danger, which can lead to death or severe injuries if the appropriate measures are not taken.
⚠️ Risk of personal injury caused by a general source of danger. This symbol indicates an imminent danger, which can lead to death or severe injuries if the appropriate measures are not taken.
❗ Important! The unit is equipped with a permanent magnet. The magnetic field may affect the function of pacemakers.
ℹ️ Important information for trouble-free operation.

Intended Use

The Waterfall Pump 1650 / 2300, referred to in the following as "unit", may only be used as specified in the following:

For pumping normal pond water for filters, waterfalls and water courses.
Operation under observance of the technical data.

The following restrictions apply to the unit:

Do not use in swimming pools.
CAUTION - this pump has been evaluated for use with water only.
Never run the unit without water.
Do not use for commercial or industrial purposes.
Do not use in conjunction with chemicals, food products, easily flammable or explosive substances.
Do not connect to the domestic water supply.
Do not exceed the voltage shown on the pump.
Inspect the power cord for damage before installation and maintenance.
Do not remove the grounding pin from the power cord plug.

Use other than that intended: This unit can be dangerous and cause harm if not used in accordance with these instructions. Any use not in accordance with these instructions or modification(s) to the unit will void the limited warranty.

Installation

WARNING: Risk of electric shock - This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly grounded, grounding-type receptacle.

Important:

Always place the unit below water level.
It is recommended to place the unit horizontally on the ground ensuring its stable position.
Do not lift the pump by its power cord. Use the handle to lift and maneuver the pump.

Steps for connecting tubing:

For maximum water flow, it is recommended that the largest tubing size for your pump is used. If needed, cut the adapter as shown using a hacksaw; consult packaging for tubing size.
Attach the adapter to the pump first, then connect tubing to the adapter. NOTE: Tubing is NOT INCLUDED.
Attach the other end of the tubing to desired water feature or spillway.

Diagram Description: Illustrates connecting the tubing adapter to the pump and then connecting the tubing to the adapter.

Start-up

Attention! The pump must never run dry. Possible consequences: The pump will be destroyed. Protective measures: Check the water level at regular intervals. Always place the unit below water level.

Attention! The installed temperature sensor automatically turns the pump off, if it is overloaded. The pump automatically switches on again once the motor has cooled down. Risk of accident! Install the unit so that it is not exposed to direct sun radiation (max. 104 °F - 40 °C).

Important: The unit switches on automatically when power connection is established.

Switching on: Connect power plug to the socket.
Switching off: Disconnect the power plug.

Maintenance and Cleaning

Attention! Dangerous electrical voltage. Possible consequences: Death or serious injuries.

Protective measures:

Electrical units and installations with a rated voltage of U > 12 V AC or U >30 V DC located in the water: Isolate the units and installations (switch off and disconnect from the power supply) before reaching into the water.
Isolate the unit before starting any work.
Secure the unit to prevent unintentional switching on.

WARNING: This pump uses a very strong magnet to achieve superior performance. When removing the impeller assembly there will be considerable magnetic force resisting the extraction of the impeller assembly. This is normal. Likewise when replacing the impeller assembly there will be a strong magnetic force pulling the assembly into the pump to potentially cause injury to fingers and in rare cases damaging the ceramic shaft or rear bearing. Use thick gloves when replacing the impeller assembly.

Cleaning the unit

Regular cleaning of the pump may be necessary depending upon the environment in which it is operated. Clean the pump when it is visibly soiled or when a drop in performance is detected. Clean the unit with warm water using a soft brush.
Never use aggressive cleaning agents or chemical solutions. These could attack the housing surface or impair the function.
In the event of stubborn furring (calcium deposits), a common household cleaner free from vinegar and chlorine can be used. Subsequently, clean the pump thoroughly using warm water.

Cleaning the pump

Disconnect the pump from the power source. Disconnect the tubing.
Disassemble the screen and remove the impeller housing to expose the impeller assembly.
Remove the impeller assembly by pulling on the back round plate behind the impeller.
Use a soft cloth or brush to clean the impeller assembly and the inside of the impeller housing. Check parts for damages such as cracked rotor, shaft, or bearing, cracks in the magnet, and broken plastics. Replace parts if necessary.
Reassemble in the reverse order.

Diagram Description: Illustrates the steps for disassembling and cleaning the pump, including removing the impeller assembly.

Storage/Winterization

Put the unit out of operation at water temperatures below 46 °F (8 °C) or, at the latest, when freezing temperatures are to be expected.
Thoroughly clean the unit, check for damage.
Ensure that the storage place is inaccessible to children.

Wear Parts

The impeller unit is a wear part and is excluded from the warranty.

Disposal

Do not dispose of this unit with domestic waste! Disable the unit beforehand by cutting off the cables. Further information about the recycling of this product can be obtained from your local municipal authority.

Troubleshooting

Issue	Cause	Solution
The unit is not performing its suction function	Power supply not connected	Connect pump power supply, check the supply lines to make sure the voltage is correct
The unit is not performing its suction function	Impeller blocked, shaft broken	Remove the inlet screen and/or pump cover, and impeller housing to expose the impeller. Turn the impeller to ensure that it is not broken or jammed by debris. Also check to make sure that the ceramic shaft or bearings are not broken.
Insufficient flow	Pump is not completely submerged	Completely submerge pump in the water
	Pump is not completely submerged	Completely submerge pump in the water
	Screen clogged	Clean
	Tubing blocked	Clean or replace tubing
	Tubing kinked	Eliminate kink, replace tubing if it is damaged
	Excessive flow loss in the tubing due to friction	Reduce tubing length to reduce frictional loss Select larger hose diameter, adapt stepped hose adapter to hose diameter.
Unit switches off after a short running period	Pump overload. The flow is automatically stopped to protect the pump.	Clean the pump housing and impeller assembly Reduce the ambient temperature (e.g. ensure that the specified water temperature is adhered to, avoid direct sunlight)
	Impeller worn	Replace impeller assembly
	Excessive soiled water	Clean impeller housing, bearing and impeller assembly
	Impeller blocked, shaft broken	Remove the inlet screen and/or pump cover, and impeller housing to expose the impeller. Turn the impeller to ensure that it is not broken or jammed by debris. Also check to make sure that the ceramic shaft or bearings are not broken.
	Water temperature too high	Maximum water temperature: +95 ° F (+35 °C)

Technical Specifications

Model	Model No.	Rated voltage	Power consumption	Max. flow rate	Max. head height	Cord length	Connection for hoses	Dimensions
1650	45421	120V / 60 Hz	75 W / 1 A	1650 GPH	16.5 ft.	20 ft.	1", 1 1/2"	8.4 x 5 x 6.23 in.
2300	45422	120V / 60 Hz	130 W / 1.5 A	2300 GPH	20 ft.	20 ft.	1", 1 1/2"	8.4 x 5 x 6.23 in.

Waterfall Pump Parts

Diagram Description: An exploded view of the Waterfall Pump components is shown.

Pos.	1650	2300	Part Name
1			Screen
2			Impeller housing
3			Impeller assembly
4			O-ring
5			1 in., 1 1/2 in. ID tubing adapter

Contact Information

Questions, problems, missing parts?

Before returning to your retailer, call us at 1-866-627-3435, 8 a.m.-6 p.m., EST, Monday-Friday, or email us at customercare@oase-livingwater.com. Or visit our website at www.oase-livingwater.com

	OASE Waterfall Pump Installation and Start-up Guide Comprehensive guide for installing and starting up OASE waterfall pumps, covering safety warnings, important notes, and step-by-step instructions for optimal performance and safe operation.
	OASE Waterfall Pump 3700 / 5150: Operating Instructions & Technical Guide Comprehensive operating instructions, installation guide, maintenance tips, and technical specifications for the OASE Waterfall Pump models 3700 and 5150. Learn how to safely set up, use, and maintain your pond pump for water features.
	Oase FP 1500/2500/3500 Pond Pump Operating Instructions Comprehensive operating instructions for Oase FP 1500, 2500, and 3500 pond pumps. Includes safety, installation, maintenance, troubleshooting, and technical specifications for water features and fountains.
	Oase Fountain Pump 320: Operating Instructions and Specifications Comprehensive operating instructions, installation guide, maintenance tips, and technical specifications for the Oase Fountain Pump 320. Learn how to safely install, use, and care for your Oase water pump.
	Oase Pump Vault 20000, 60000, Extension: Pond Filtration System Guide Comprehensive guide to the Oase Pump Vault series (20000, 60000, Extension) for efficient pond filtration. Includes installation, compatibility, and application details.
	Oase Waterfall 30, 60, 90, XL 30, XL 60, XL 90 Operating Instructions Comprehensive operating and installation guide for Oase Waterfall water features, including dimensions, pump recommendations, and assembly steps for models 30, 60, 90 and XL variants.
	Oase AquaOxy 450 Operating Instructions Comprehensive operating instructions for the Oase AquaOxy 450 pond aerator, covering installation, startup, maintenance, troubleshooting, and disposal.
	OASE FiltoClear Pond Filter Manual: Installation, Operation, and Maintenance Guide Comprehensive operating manual for OASE FiltoClear 12000, 16000, 20000, and 30000 pond filter systems. Includes installation, maintenance, troubleshooting, and technical data for garden pond water treatment.