MOES ZigBee Smart Switch Instruction Manual

Product Description

This ZigBee Smart Switch is designed to replace traditional wall switches, offering smart control capabilities via the ZigBee protocol. It supports both Neutral+Live (N+L) wire and Live-only (L) wire configurations, requiring a ZigBee hub for operation. The switch features multi-control association, allowing multiple switches to control a single light when using the N+L wiring method. Its design aims to blend with various home decoration styles.

Technical Parameters

Safety Information

Risk of Electric Shock:

Electricity can cause personal injury and property damage if handled improperly. If you are unsure about any part of these instructions, seek professional assistance from a qualified electrician.

• Do not disassemble, reassemble, modify, or attempt to repair the product yourself. Such actions may cause electric shock, leading to serious injury or death.

Installation Guide

Warnings:

• Turn off the power at the circuit breaker and test that power is off before wiring.
• Please disconnect the power supply before installing or removing the device to avoid irreversible damage from electric current or unpredictable problems like lamp flashing.

Note: Ensure the power at the circuit breaker is off before wiring. Two versions are available: one requiring a Neutral wire and one that does not. Please make the correct wiring according to the switch version purchased. If your switch requires a neutral wire, confirm your wall box contains one (typically white). If not, try another location or call a professional electrician. Wire colors in this manual are typical and may differ. Ensure wire conductors are securely fastened. Ensure Wi-Fi signal is steady and your mobile and Zigbee gateway hub are on the same 2.4GHz WiFi network. If you lack wiring experience, call a professional electrician.

1. Step 1: Turn Off Power

   Turn off the circuit breaker and use an electrical tester to confirm power is off before wiring.

2. Step 2: Remove Old Switch

   Remove the faceplate from the old switch. Use an electrical tester to ensure no voltage is present in the circuit. You may need to turn off more than one circuit breaker.

3. Step 3: Disconnect and Identify Wires

   Remove the old switch and pull it away from the wall. Identify the Line/Load wires. (Note: The color of your wire may differ from the colors shown in diagrams.)

4. Step 4: Document Wiring

   Take pictures of the existing wiring for reference. Follow the wiring diagram to connect the switch wires to the wall wires using wire conductors.

   Wiring Diagram Description: The diagram shows a central switch unit with terminals labeled L (Line/Live), N (Neutral), and L1, L2, L3 (for controlling Light 1, Light 2, Light 3 respectively). The input power lines (L and N) connect to the switch's L and N terminals. Output lines (L1, L2, L3) connect to the respective light circuits. This diagram illustrates how to connect the switch wires to the wires in the wall box using wire conductors.

5. Step 5: Mount New Switch

   Open the switch panel from the bottom of the new switch using a screwdriver. Mount the switch using the provided screws and snap the wall plate onto it.

   ? [Screwdriver icon]

6. Step 6: Restore Power and Test

   Turn the power back on at the circuit breaker. Test the switch to ensure the light turns on and off correctly.

Add Devices (App Configuration)

This section guides you through connecting the smart switch to your smartphone via the Smart Life app.

1. 1. Download Smart Life App

   Scan the QR code provided in the original document or search for "Smart Life" on your device's app store and download it.

2. 2. Registration or Log In

   Open the "Smart Life" application. Tap "Register" to create an account using your phone number and a verification code, then set a password. If you already have an account, choose "Log in".

3. 3. Configure the APP to the Switch

   Preparation: Ensure the switch is connected to electricity, your phone is connected to Wi-Fi, and can access the internet.

   Note: If you have connected to a 5GHz WiFi network, please disconnect it first and connect to a 2.4GHz WiFi network, as ZigBee devices typically operate on this band.

Steps for connecting the APP to the device:

Ensure the device is within the effective signal coverage of your smart ZigBee gateway for successful connection.

1. Method One: Scan QR Code Configuration

   Make sure your Smart Life/Tuya Smart APP has successfully connected to a Zigbee gateway. Follow the on-screen prompts in the app to scan a QR code for network configuration.

2. Method Two: Manual Pairing

   Make sure your Smart Life/Tuya Smart APP has successfully connected to a Zigbee gateway. Press and hold the button on the switch for approximately 7 seconds. The indicator light on the switch will flash fast after about 3 seconds, indicating it has entered pairing mode. Repair is successful.

3. 3. Enter Gateway Pairing Mode

   Follow the app's visual guide to finish adding the sub-device. The indicator light should be blinking. The connecting process typically takes 10-120 seconds, depending on network conditions.

4. 4. Add Device Successfully

   Once the device is added successfully, you can edit its name and enter the device page by clicking "Done".

How to Reset/Re-pair ZigBee Code

To reset or re-pair the ZigBee connection:

1. Press and hold the button on the switch for approximately 7 seconds, until the indicator light flashes fast after 3 seconds. Reset/Re-pair is successful.
2. In the app, you will see the device. Click the main switch to enter the next operation.
3. Click "Done" to enter the device page and enjoy your smart life with home automation.

How to Achieve Multi-Control Association (Only for N+L Wire)

Note: Please confirm you have successfully linked the switch to your Smart Life App before proceeding with association.

1. 1. Add Another Smart Switch

   Add another smart switch to the same Smart Life/Tuya App. If a smart switch has already been added, proceed to the next step.

   Note: If your switch requires a neutral wire, the newly added switch does not need to be wired to the light; only L and N are required for wiring. This allows you to control one light with multiple switches in the Smart Life/Tuya App. If your switch does not require a neutral wire, follow the wiring instructions to connect L and the light. You can then control lights simultaneously with multiple switches.

   Visual representation: ? [Lightbulb icon] ⚙️ [Settings icon] ➡️ [Arrow icon] ? [Lightbulb icon]

   Diagram Description: Shows "New Added Switch" and "Main Switch" as separate entities.

2. 2. Access Association Settings

   In the app, click the upper right corner icon [options icon], choose "Multi-Control Association", and then click the "+" icon [add icon] in the right corner.

3. 3. Select Switch and Button

   Choose the switch you want to associate and then select the specific switch button that will control the same light. Go back to the previous page. You will see two items listed: your main switch and the newly associated switch.

   Note: Please confirm the associated switch is enabled.

4. 4. Control with Multiple Switches

   You are now able to control your light with two switches. Do not associate another button on the same switch for multi-control. If you wish to add a third or more smart switches to control the same light, repeat the steps above.

   Visual representation: ? [Lightbulb icon] ⚙️ [Settings icon] ➡️ [Arrow icon] ? [Lightbulb icon] ⚙️ [Settings icon] ➡️ [Arrow icon] ? [Lightbulb icon]

   Diagram Description: Shows "Main Switch", "Associated 1", and "Associated 2" controlling a single light.

Voice Control with Alexa

Integrate your smart switch with Amazon Alexa for voice control.

1. 1. Complete Product Networking Configuration

   Ensure the device is connected to your network via the Smart Life app. It is recommended to name the device in the app with an easily identifiable name, such as "bedroom light" (names are usually in English).

2. 2. Configure Amazon Echo Device

   If you have already configured Amazon Echo, skip this step. The following instructions are based on the iOS client:

   • Make sure your Amazon Echo device is powered on and connected to a Wi-Fi network.
   • Open the Alexa APP on your phone and log in.
   • Tap the menu icon [menu icon] in the upper left corner of the Home page, select "Settings", and tap "Set Up A New Device" to set up the Amazon Echo.
   • Choose your Amazon Echo device type and language for connecting.
   • Press and hold the small dot on the Echo device until the light turns yellow.
   • Click "Continue" to connect to the Echo's hotspot, then return to the Alexa APP page.
   • Click "Continue" to find and connect to your home Wi-Fi network.
   • Amazon Echo will take a few minutes to connect to the network.
   • After successful network connection, tap "Continue". An introduction video will play. After the video, tap "Continue" to jump to the Alexa Home page. You have now completed the Amazon Echo's configuration process.

3. 3. Link Skill

   Tap on "Skills" in the Alexa App menu. Search for the "Smart Life" app name. Tap "Enable" to activate the Skill. Enter your Smart Life app account and password, then tap "Link Now" to link your app account and enable the Skill. You can now start your smart home journey.

4. 4. Common Commands

   Control your smart device via voice commands with Echo:

   • "Alexa, turn on <device name>"
   • "Alexa, turn off <device name>"

Troubleshooting

1. Why does the device fail to link to the APP?

   • a. ZigBee products require a MOES/TUYA ZigBee gateway.
   • b. Check if the router connected to the gateway is online. Ensure the gateway has a good Wi-Fi signal and try connecting the gateway again.
   • c. Check if the device is too far from your gateway or other ZigBee devices. Keep the ZigBee gateway and the ZigBee device close (less than 5 meters) to form a mesh network.
   • d. Verify that the device has entered the network distribution mode.

2. After the device is installed, why does the light not respond when I click the switch button?

   Please disconnect the power supply and check if the connection is correct according to the instructions.

3. Why is there no reset button on my switch?

   The reset button is typically the switch button itself. You can long-press the switch button for APP configuration. The power indicator light will start blinking when the device enters successful pairing mode.

4. What if my smart switch malfunctions and doesn't respond for a long time?

   Please try resetting the device. First, remove the smart switch from your APP and then re-configure the network for use.

Transportation and Storage

Transportation

Products should be free from severe vibration, impact, exposure to rain, dumping, and other issues during transportation. Comply with the provisions indicated by marks on the packing boxes.

This product has no waterproof and dustproof function.

Storage

Products should be stored in a warehouse where the temperature is between -10°C and +45°C, and the relative humidity is below 70% RH. The environment should be free from acid, alkali, salt, corrosive substances, explosive gases, and flammable matter. Protect from dust, rain, and snow.

Recycling Information

All products marked with the WEEE symbol (separate collection of waste electrical and electronic equipment, WEEE Directive 2012/19/EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment, as appointed by the government or local authorities. Correct disposal and recycling help prevent potential negative consequences for the environment and human health. Contact your installer or local authority to find out where these collection points are and how they operate.

Service and Warranty

1. During the free warranty period, if the product breaks down during normal use, free maintenance will be provided.
2. The warranty does not cover: natural disasters/man-made equipment failures, disassembly and repair without company permission, lack of warranty card, or products beyond the free warranty period.
3. Any commitment (oral or written) made by a third party (including dealers/service providers) to the user beyond the warranty scope is the responsibility of that third party.
4. Please keep this warranty card to ensure your rights.
5. MOES may update or change products without notice. Refer to the official website for updates.

Contact and Manufacturer Information

Manufacturer: WENZHOU NOVA NEW ENERGY CO.,LTD

Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China

Tel: +86-577-57186815

After-sale Service: service@moeshouse.com

European Representative: EVATOST CONSULTING LTD

Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR

Tel: +44-292-1680945

Email: contact@evatmaster.com

Distributor: AMZLAB GmbH

Address: Laubenhof 23, 45326 Essen

Made In China

Company Information

Thank you for your support and purchase from MOES. We are always here for your complete satisfaction. Feel free to share your shopping experience.

For any other needs, please contact us.

Follow us: @moessmart, @moes_smart, MOES.Official, @moes_smart

Website: www.moes.net