OttLite Wireless Charging LED Lamp with Colour Changing Base

Congratulations and Product Registration

Congratulations on your purchase of the finest in natural lighting technology with your new OttLite® product.

Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OttLite.com/warranty

Setup Instructions

WARNING: To prevent electric shock, ensure the lamp is not plugged in until all steps are complete.

This unit is fully assembled. Remove the lamp from its packaging and place the lamp body base (A) flat on a steady surface.

Connect the power adapter input (J) into the connector (K) located at the rear-bottom of the lamp.

Plug the power adapter (L) into a standard household 230V outlet. Note: Only use the supplied power adapter to avoid damage or fire.

The power switch (B) is a touch switch that controls ON/OFF power, LED brightness settings, and the colour mode function of the lamp.

To power the main light:

• Turn lamp "ON" to the 1st brightness setting: slightly touch the switch (B) once.
• For the 2nd brightness setting: touch the switch (B) twice.
• For the 3rd brightness setting: touch the switch (B) three times.
• To turn the lamp "OFF": touch the switch (B) four times.

This lamp provides three colour modes. To adjust the lighting colour mode, slightly "press and hold" switch (B) for three seconds to cycle through colour temperatures: 5000°K, 2700°K, 4000°K.

Touch button (C) to turn on the colour changing base. When the desired colour is shown, touch button (C) again briefly to maintain that colour; otherwise, colours will shift continuously. Touch and hold button (C) to turn off the colour changing base.

To reposition the light, hold the lamp base (A) steady and grasp either the lamp body (E) or shade (F) depending on the needed adjustment.

Refer to Diagram 1 and Diagram 2 for the lamp's maximum adjustment range. Note: DO NOT FORCE the shade outside the allowable adjustment range, as excessive adjustment may cause damage.

? Read instructions prior to use.

Diagram 1 Description: Illustrates the flexible gooseneck of the lamp and the articulation of the lamp head, pointing out components like the lamp body (E) and base (A).

Diagram 2 Description: Shows the range of motion for the lamp head, indicating how it can pivot and tilt.

Wireless Charging Instructions

Wireless charging requires a Qi-certified device. To determine if your device is Qi-certified, please visit the Wireless Power Consortium website.

To wirelessly charge a device:

• Place the device, which supports the Qi wireless charging standard, face up on the middle of the wireless charging icon (D).
• When the device is centered on the Qi wireless charging area (D), a solid RED light (P) will come on, indicating charging mode is active. Note: If the RED light is blinking, this indicates the device is not charging. Your device should show that charging is taking place.
• Check the charge level on your device periodically to determine when the device is fully charged.
• Note: The product DOES NOT provide any indication of when the device is fully charged.

CAUTION: Device may become warm during charging. This is normal and part of the process. Charging times vary by device.

The wireless charging area is indicated by a [qi logo] symbol.

Control Panel and Settings

Refer to the following icon legend for the control panel (M), as it pertains to the instructions for various setting functions below:

• [Setting Button] – to set time and calendar; in alarm mode, push to turn off alarm.
• [Mode Button] – push to set alarm and snooze.
• [Up Button] – In setting mode, push to increase.
• [Down Button] – In setting mode, push to decrease.
• [Display Key] – Push display key for suitable brightness.

Calendar and Clock Setting:

Note: The Control Panel (M) to set Calendar and Clock is located behind the lamp body (E).

• Under normal mode, press the [Setting Button] to enter setting mode. Press the [Setting Button] again for the next setting. The sequence of setting is: HOUR-MINUTE-YEAR-DAY-MONTH.
• Press the [Setting Button] to quit setting, or it will automatically quit to normal mode if idle for 60 seconds.
• Under normal mode, press the [Up Button] to switch between "12h" and "24h" display.

Alarm & Snooze Function Setting:

• Under normal mode, press the [Mode Button] to enter alarm mode.
• Under alarm mode, press the [Setting Button] to enter alarm setting. Press the [Setting Button] again for the next setting; the sequence of setting is: HOUR-MINUTE-SNOOZE-MUSIC, and then exit.
• Note: There are 8 music tones to select.
• Press the [Up Button] and [Down Button] to adjust the alarm time sequence.
• Under alarm mode, press the [Up Button] and [Down Button] to turn ON/OFF the alarm and snooze function. A [music note icon] will light up on the display to indicate the alarm is set. A [snooze icon] will appear on the display to indicate snooze is activated.
• Snooze can be set from 1 to 60 minutes.
• When the alarm time is reached, the alarm will ring for 1 minute, then snooze and ring again. Press the [Setting Button] to turn OFF the alarm or touch the [Up Button] and [Down Button] to activate snooze. Note: Snooze defaults to 60 minutes if loss of power occurs.

Temperature Switch Setting:

• In normal mode, touch the [Down Button] to switch between °F and °C display.

Clock Display Brightness:

• Press the [Display Key], located above the [Setting Button] and [Mode Button], to change the clock display brightness level.

Safety Warnings

⚠️ CAUTION! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:

• Turn the lamp off and WAIT UNTIL THE LAMP HEAD (G) IS COOL before handling.
• The LED panel (G) might get hot after several hours of continuous use. DO NOT place your hands directly on the LED light panel.
• Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
• Do not alter the plug.
• The lamp head included with this unit cannot be replaced by the consumer.
• INDOOR USE ONLY.

Note: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.

Battery Replacement

• This lamp uses a CR2032 battery. For battery replacement, see diagram. The battery compartment (N) is located behind the lamp body (E).
• To remove/install the button cell battery: use a screwdriver to remove the battery compartment door (O). The button cell battery is to be installed with the "+" or flat side facing upward.

Battery Disposal

Battery disposal should be in compliance with local regulations pertaining to the disposal of hazardous materials. DO NOT INCINERATE.

Battery Safety Warning

⚠️ CAUTION: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD!

• This lamp contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
• Keep new and used batteries away from children.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Note: Coin/button cell batteries are small, single cell devices having a diameter greater than their height.

Final Caution

⚠️ CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.