Mito Red Light Universal Stand User Manual

Brand: Mito Red Light

Introduction

This manual provides comprehensive instructions for assembling and using the Mito Red Light Universal Stand. The stand is designed to support Mito Red Light Therapy panels in either vertical or horizontal configurations.

Important Safety Precautions:

Read this user manual carefully before beginning assembly or use.
Severe personal injury and property damage can result from improper installation or assembly.
The universal stand is intended for use with Mito Red Light Therapy panels only.
Ensure the stand is placed on a level floor and that the wheels are locked after installation.
Do not install or assemble if the product or hardware is damaged or missing. Contact Mito Red Light for replacement parts.
This product fits most 21" x 71" red light therapy panels. The maximum weight capacity is 46 KG or 100 lbs.
Do not use this product for anything other than its original design.
This product contains moving parts; please use with caution.
The manufacturer disclaims liability for damages arising from modifications, improper installation, or exceeding the specified weight range.
Children should not use the stand unless approved by a physician.

Product Specifications

The Universal Stand supports both Vertical and Horizontal Mounting configurations for Mito Red Light panels.

Dimensions:

Base Width: 33.2" (845mm)
Base Depth: 28.1" (716mm)
Adjustable Height (Vertical): 41.3"-59" (1050-1500mm)
Height (Horizontal): 41.3" (1050mm)

Parts List

The following parts are included in the Universal Stand kit:

A: M8x25mm Bolts (6x)
B: M8x65mm Bolts (8x)
C: M5x12mm Bolts (4x)
D: Brackets (2x)
E: Washers (4x)
F: M6 Bolts (1x)
G: M8x8mm Bolts (26x)
H: M5 Bolts (1x)
I: Knobs (4x)
J: Base (1x)
K: Vertical Poles (1x)
L: Mounting Arms (2x)
M: Caster Wheels (4x)
N: Front Vertical Stand Adapter (1x)
O: Horizontal Bracket (1x)
P: Horizontal Bracket (1x)
Q: Horizontal Mounting Brackets (2-4x, depending on setup)
R: Vertical Mounting Brackets (4x)
S: Horizontal Poles (2x)
T: Rear Vertical Stand Adapter (1x)
U: Top Cover (1x)

Base Assembly Instructions

Locate the base (J) and flip it upside down.
Find the four caster wheels (M). Press the brakes on each caster wheel to prevent movement during installation.
Place one washer (E) onto each caster wheel (M). Screw each caster wheel clockwise into the four corners of the base (J) until tightly secured.
Return the base (J) to its normal position with the caster wheels facing downward.
Locate the vertical poles (K). Align the poles with the slots on the base (J), ensuring the cable management holes face the rear. Gently lower the poles into the designated slots until securely seated.
Insert four bolts (A) into the designated holes in the base (J) – two from the top and two from the bottom. Use the Allen wrench (H) to tighten the bolts until snug.
Verify the poles are securely attached and aligned. Slide the cover (U) over the top holes, gently pinching the tabs to insert them for a secure fit.
Adjusting Pole Height: Remove the preinstalled shipping security bolts. Locate the spring plunger ball on the right lower pole. Press the ball to unlock the pole and pull it upwards to the desired height. Align the spring plunger ball with the nearest hole and twist slightly to engage. Repeat for the left upper pole.
Once both poles are at the desired height, reinsert the safety bolts into the predrilled holes above the plunger. Use the Allen wrench (H) to tighten the safety bolts to lock the poles in place. Ensure they are snug but avoid over-tightening.

Vertical Mounting Instructions

Decision Point: Vertical or Horizontal Mounting

Choose between vertical and horizontal mounting based on your space, preferences, and intended use. Vertical mounting is ideal for maximizing height coverage and narrow spaces, while horizontal mounting is suitable for wider areas where height is less critical.

Step 1: Mount Adapters

Locate the front (N) and rear (T) vertical stand adapters and four bolts (B).
Align the adapters with the top of the poles, ensuring the four predrilled holes align.
Insert the bolts (B) and hand-tighten to hold the adapters in place.

Step 2: Tighten Bolts

Use the Allen wrench (H) to tighten the bolts (B) clockwise until snug. Avoid over-tightening.

Step 3: Attach Mounting Brackets

Locate the four vertical mounting brackets (R) and fourteen bolts (G).
Identify your specific panels to determine the correct bracket attachment method.
Refer to the diagrams and hand-tighten the bolts (G) in alignment with the red dots for your panel configuration.

Panel Configuration Notes:

MitoPRO+ and PRO X: Always place the MitoPRO 1500+/X on top. Use at least 3 screws on each side to attach brackets to the MitoPRO 1500+/X, and at least 3 screws on each side for the MitoPRO 750+/X.
MitoADAPT 3.0: Place the MitoADAPT MAX 3.0 as the top panel and MitoADAPT MID 3.0 below. Screw positions are noted in red circles. For MitoADAPT MEGA, refer to specific instructions.
MitoPRO+ Elite/Mega or MitoADAPT - Elite/Mega: Use the provided Allen wrench (F) to tighten bolts (G) securely.

Step 6: Hang Panel

Carefully hang the panel, with attached vertical mounting brackets, onto the vertical cross bracket on the stand.

Step 7: Secure Panel

Locate the two tab pieces (D) and two screws (C).
Align the tab pieces (D) as shown in the diagrams. Insert and tighten the screws (C) into the attachment points on the outside of the outer brackets to secure the panel. Ensure all components are properly aligned and tightened for stability.
For ADAPT Panels: Use the longer, white tab pieces provided separately with ADAPT brackets. Use the provided screws to attach panels. Each tab requires two screws. Disregard the smaller metallic tabs.

Horizontal Mounting Instructions

Step 1: Attach Horizontal Brackets

Locate the two horizontal brackets (O) and (P), and four bolts (B).
Position bracket (O) to face the front of the stand.
From the rear, hand-tighten all four bolts (B) to temporarily hold the brackets.
Use the Allen wrench (H) to securely tighten the bolts.

Step 2: Attach Horizontal Poles

Locate the two horizontal poles (S) and four bolts (B).
Align the poles with the corresponding holes and hand-tighten the bolts.
Use the Allen wrench (F) to securely tighten the bolts.

Step 3: Attach Horizontal Mounting Brackets

Locate two to four horizontal mounting brackets (Q) and twenty-six bolts (G).
Ensure all necessary components are present before proceeding.

Step 4: Configure Brackets for Panels

Identify your specific panels to determine the correct method for attaching the horizontal mounting brackets (Q).
Refer to the diagrams and hand-tighten the bolts (G) in alignment with the red dots for your panel configuration.

Panel Configuration Notes:

MitoPRO+ and MitoPRO X: For configurations with MitoPRO 750+ and 1500+ or MitoPRO 750X and 1500X, always place the MitoPRO 1500+/X on top. Use at least 4 screws on each side for the MitoPRO 1500+/X and at least 3 screws on each side for the MitoPRO 750+/X.
MitoADAPT 3.0: Always place the MitoADAPT MAX 3.0 as the top panel and MitoADAPT MID 3.0 below. Use at least 3 screws on each side to attach brackets to the MitoADAPT MAX and MitoADAPT MID.

Step 5: Tighten Bolts

Using the Allen wrench (F), tighten the bolts (G) securely. Ensure they are snug but avoid over-tightening.

Step 6: Secure Panel with Knobs

This step may require two people: one to hold the panels and one to tighten the knobs.
Locate the four knobs (I).
Carefully position the panel beneath the horizontal poles, ensuring the attached horizontal mounting brackets are properly aligned.
Secure the panel by screwing in the four knobs (I) by hand until they are secure. Avoid over-tightening.

Support and Contact Information

For user manuals and instructional videos, visit: https://mitoredlight.com/pages/user-manual

For further questions, please contact Mito Red Light:

Email: info@mitoredlight.com
Phone: +1866-861-6486 (Monday - Friday, 9am - 5pm MST)
Mailing Address: Mito Red Light, LLC, 9319 N 94th Way, Suite 400 Scottsdale, AZ 85258

Follow Mito Red Light on Social Media:

Facebook: /mitoredlight
Instagram: /mitoredlightofficial
Twitter: @MitoRedLight
TikTok: @mitoredlightofficial

Document Updated: March 2025

	Mito Red Light Universal Stand User Manual: Assembly and Operation Guide Comprehensive user manual for the Mito Red Light Universal Stand. Provides detailed assembly instructions for vertical and horizontal mounting, parts list, product specifications, and important safety precautions for MitoPRO and MitoADAPT panels.
	MitoPRO X Series User Manual - Mito Red Light Comprehensive user manual for the MitoPRO X Series red light therapy devices from Mito Red Light. Covers setup, operation, safety, contraindications, FAQs, mobile app usage, installation, light therapy overview, warranty, and refund policies.
	Mito Red Light User Manual: Benefits, Safety, and Model Comparison Comprehensive user manual for Mito Red Light devices, covering getting started, benefits of red and near-infrared light therapy, contraindications, safety instructions, FAQs, model comparisons, warranty, and refund policy.
	Mito Red Light Product Manual: Safety, Specifications, and Policies Explore the Mito Red Light product manual, featuring comprehensive safety guidelines, detailed specifications for MitoPRO devices, maintenance instructions, warranty details, and refund policies for optimal user experience.
	MitoADAPT 3.0 User Manual: Comprehensive Guide to Light Therapy Device Operation and Benefits This user manual provides detailed instructions for the MitoADAPT 3.0 series of red and near-infrared light therapy devices. It covers setup, operation, mode selection, app integration, troubleshooting, safety guidelines, and an overview of light therapy principles.
	MitoPRO+ v2 Series User Manual \| Mito Red Light Therapy Comprehensive user manual for the MitoPRO+ v2 Series red light therapy device from Mito Red Light. Learn about setup, operation, safety, contraindications, warranty, and more.
	MitoPRO+ Series User Manual - Mito Red Light Comprehensive user manual for the MitoPRO+ Series red light therapy devices by Mito Red Light, covering setup, operation, safety, FAQs, contraindications, warranty, and light therapy overview.
	MitoPRO+ / MitoPRO X Floor Stand Assembly and Wall Mount Guide Comprehensive guide for assembling the MitoPRO+ and MitoPRO X floor stand from Mito Red Light. Includes step-by-step instructions for attaching wheels, mounting panels, and securing the unit to a wall for enhanced stability.