ASUS ROG STRIX B650E-E GAMING WIFI Motherboard

Introduction

This guide provides essential steps for installing and setting up your ASUS ROG STRIX B650E-E GAMING WIFI motherboard.

Motherboard Layout

The motherboard is ATX form factor (30.5cm x 24.4cm). Key features include:

• AM5 CPU socket
• Four DDR5 DIMM slots (labeled DIMM_A1, DIMM_A2, DIMM_B1, DIMM_B2)
• Multiple M.2 slots for NVMe SSDs (supporting various lengths like 2242, 2260, 2280, 22110)
• PCIe slots (including PCIEX16_1, PCIEX16_2, PCIEX16_3 for graphics cards and other expansion cards)
• SATA 6Gb/s ports (SATA6G_E1/2, SATA6G_E3/4)
• 24-pin ATX power connector (ATX_PWR)
• 8-pin CPU power connectors (ATX_12V_1, ATX_12V_2)
• CPU and chassis fan headers (CPU_FAN, CPU_OPT, AIO_PUMP, CHA_FAN1-5)
• RGB headers
• System panel connector header
• USB headers
• Wi-Fi M.2 slot
• BIOS FlashBack™ button and LED
• Q-Code diagnostic LEDs
• Boot device LEDs (VGA, BOOT, DRAM, CPU)
• Super I/O chip
• Audio header
• TPM header
• Temperature sensor headers (T_SENSOR)

Step 1: Install the CPU

CPU Installation:

1. Open the CPU socket lever by pushing it down and then to the side.
2. Align the CPU's triangle mark ▲ with the corresponding triangle mark on the socket.
3. Gently place the CPU into the socket. Do not force it.
4. Close the CPU socket lever by pushing it back into its original position.

Note: Remove only the screws and the retention module. Do not remove the plate on the bottom.

Step 2: Install the CPU Fan

Mount the CPU cooler according to its specific instructions. Ensure proper alignment and secure attachment to the motherboard. Connect the fan cable to the CPU_FAN header.

Step 3: Install Memory Modules

Open the clips on the DIMM slots (e.g., DIMM_A1, DIMM_A2). Align the notch on the memory module with the notch in the slot. Push down firmly on both ends of the module until the clips snap into place. Refer to the motherboard manual for optimal dual-channel or multi-channel configurations.

Step 4: Install Storage Devices

To install M.2 storage devices, align the M.2 drive with the slot and secure it with the provided screw. Refer to the motherboard manual for specific slot locations and installation details.

Step 5: Install Expansion Cards

Open the retention clip on the desired PCIe slot (e.g., PCIEX16_1). Remove the corresponding slot cover(s) from the back of the PC case. Align the expansion card with the slot and push down firmly until it is seated and the clip locks.

Step 6: Connect System Panel Connectors

Connect the small cables from your PC case's front panel (e.g., Power Switch ⚡, Reset Switch, HDD LED, Power LED) to the corresponding pins on the system panel header on the motherboard. Refer to the motherboard manual for precise pin assignments.

Step 7: Install ATX Power Connectors

Connect the main 24-pin ATX power supply connector (? ATX_PWR) to the motherboard. Connect the 8-pin CPU power connector (? ATX_12V_1 or ATX_12V_2) from the power supply to the corresponding socket on the motherboard.

Step 8: Connect Input/Output Devices

Connect your peripherals to the rear I/O panel. This typically includes display outputs (HDMI, DisplayPort), USB ports, Ethernet port, and audio jacks. Also, connect internal devices like front panel USB headers and audio headers to their respective connectors on the motherboard.

Step 9: Power On and Install OS/Drivers

Connect your monitor, keyboard, and mouse. Power on the system. Access the BIOS/UEFI by pressing the designated key (usually DEL or F2) during boot. Configure boot order and install your operating system from a USB drive or other media. After OS installation, install the necessary motherboard drivers from the ASUS support website.

Notices

Australia Statement Notice

From 1 January 2012 updated warranties apply to all ASUS products, consistent with the Australian Consumer Law. For the latest product warranty details please visit https://www.asus.com/support/. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

If you require assistance please call ASUS Customer Service 1300 2787 88 or visit us at https://www.asus.com/support/.

India RoHS

This product complies with the "India E-Waste (Management) Rules, 2016" and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1% by weight in homogenous materials and 0.01 % by weight in homogenous materials for cadmium, except for the exemptions listed in Schedule II of the Rule.

Türkiye RoHS

AEEE Yönetmeliğine Uygundur

HDMI Trademark Notice

The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.