ACTIVESHOP Glow MX6 / MX3 Lamp User Manual

Importer Information

Importer: ACTIVESHOP Sp. z o.o.
Graniczna 8b, building DC 2a
54-610 Wrocław, Poland
www.activeshop.com.pl

Technical Data

HD-M6X Lamp Construction and Assembly

1. Assembling the Lamp Stand: Screw the lower part of the stand (Part D) into the base. Then, screw the upper part of the stand (Part C) into the lower part (Part D).

Diagram Description: Shows the base of the lamp stand labeled 'Podstawa'. Part D is screwed into the base. Part C is screwed into Part D. The lamp is shown at the top. Arrows indicate assembly steps.

2. Attaching the Lamp to the Stand:

• Loosen the fixing screw.
• Pull part B out of part C.
• Rotate part A with part B.
• Insert part B into part C.
• Tighten the fixing screw.
• Connect the power supply cables.

Diagram Description: Illustrates the lamp head and arm assembly. Steps shown include loosening a screw, pulling out part B from part C, rotating part A with part B, inserting part B into part C, tightening a screw, and connecting power cables.

Note: The lamp stand is positioned on the stand base, ensuring lamp stability.

HD-M3X Lamp Construction and Assembly

1. Screw the lamp into the upper part of the tilted stand.

2. Connect the cable to the special guide holders.

3. Attach the lamp stand to the mounting bracket.

4. Connecting the lamp to the stand

5. Connect the power cable to the power source.

Diagram Description: Shows the lamp arm ('Uchylne ramię'), the stand ('Statyw'), and a mounting bracket ('Uchwyt mocujący'). It indicates screwing the lamp into the stand, routing cables, and attaching the stand to the bracket.

Note: The tightness of the pivoting arm connections can be adjusted with the Allen key. After prolonged or intensive use of the lamp arm, excessive joint looseness may occur. Improve connection tightness by tightening the fixing screws.

Caution! Do not overtighten the screws. If the fixing screws are overtightened, there is a risk of damaging the lamp arm.

HD-M3X/HD-M6X Lamp Operation

Diagram Description: Shows the lamp control panel with buttons.

The control panel includes:

• Power button ('Przycisk włącz wyłącz')
• Brightness Up/Down buttons ('Zwiększ jasność' / 'Zmniejsz jasność')
• Light Mode Change button ('Zmiana tryby świecenia') / Warm/Cold Color button ('Ciepła/Zimna barwa' - optional)

Note: The remote control is not mandatory in the lamp set (some models do not include a remote control).

Note: The light mode change button on the lamp control panel is not mandatory (some models do not have this button).

SAFETY MEASURES

1. The device is professional equipment intended for use in cosmetic operations. Using the device only under the guidance of qualified cosmetic personnel helps avoid unwanted effects during treatment.
2. The device must not be disassembled or attempted to be used for other purposes not specified in these instructions. All maintenance and repair work may only be carried out by an authorized service technician (ACTIVESHOP SP. Z O.O. company).
3. Do not install or use the device near liquids, in damp places, or with wet hands – so that liquids do not get into the device.
4. Immediately disconnect the device from the socket and contact the authorized service center provided by ACTIVESHOP SP. Z O.O.) in the following cases: (a) liquid has entered the device, (b) the device emits an unusual smell, smoke, or makes unusual noises, (c) the power cord is damaged, (d) the device has tipped over or its casing is damaged.
5. Do not place any objects on the cables. Do not install the device in places where someone might step on the power cable.
6. For safety reasons, unplug the power cord from the socket each time you finish working with the device.
7. Do not insert anything into the device openings. If a foreign object enters an opening, unplug the cable and contact the distributor or manufacturer.
8. Do not place the device on an unstable trolley, shelf, or vehicle. The device may be damaged if it falls.
9. To ensure a fixed device lifespan, it is recommended to observe a one-minute interval before pressing the power button again (between switching on and off).
10. The power supply must comply with the specifications indicated on the nameplate. Otherwise, there is a risk of device malfunction, damage, or even burnout.

CAUTION:

1. If the power cord is damaged or other malfunctions occur, contact the authorized service center to avoid danger.
2. This device may be used by children aged 8 and over, and persons with reduced physical and mental capabilities, as well as with insufficient experience and knowledge of the device, provided that supervision is provided or instructions for safe use of the device are given, so that the associated risks are understood.
3. The equipment is not intended for play with children. Do not let children play with the device.
4. Do not leave the device unattended if children or persons without sufficient knowledge of its use are nearby.
5. This electrical device is not a toy. Improper use or contact with the electrical device can endanger health or cause death, therefore the device must be used and stored out of reach of children.

DEVICE DISPOSAL

Dispose of used electrical devices, accessories, and packaging at recycling centers in accordance with environmental protection principles. Electrical devices must not be disposed of in household waste containers. Follow the regulations for the disposal of this type of equipment. To protect the environment in accordance with Directive 2012/19/EU on waste electrical and electronic equipment.

Waste electrical and electronic equipment must be collected separately and taken to collection points for waste electrical and electronic equipment.

Used and old devices contain fully recyclable components, so they must be sent for recycling. Therefore, they must be handed over to the respective collection points, as well as ACTIVESHOP SP. Z O.O.

STORAGE AND TRANSPORTATION

The device must be transported at a temperature from (-) 20 °C to (+) 50 °C only in its original packaging. The device should be stored in a well-ventilated room where relative humidity does not exceed 75%. Working temperature from (+) 10 °C to (+) 40 °C.

During storage and transportation, the device must not be thrown or dropped, subjected to mechanical shocks, or atmospheric influences.