Product Overview
This document provides the user manual for the VEVOR Retractable Patio Awning, Model SDA200120.
Model: SDA200120
Product Description: A retractable patio awning designed to provide shade and reduce glare.
General Guidelines & Mounting Notes
General Guidelines
- Please read these tips carefully and use the product correctly.
- If gifting the product, please keep these tips and send them to the receiver.
- For brevity, not all possible scenarios and installation details are described. For more information, please contact VEVOR.
Mounting Notes
- Ensure all parts are complete and intact before assembly.
- Mount the product on a level and firm ground.
- Verify the wall is suitable for mounting before installation.
- In windy weather, retract or dismantle the product. Recommended for use in wind speeds below force 2.
- Ensure the product is securely fixed between the ceiling and the floor and does not come loose.
- Keep people clear of the product's range when it is extended or retracted.
- If mounting on a balcony, secure it with a rope to prevent falling.
- It is strictly forbidden to hang any objects on the product.
- The product's service life, especially plastic parts, depends on weather conditions; check the product regularly for good condition.
- When unpacking, use scissors with rounded corners to avoid damaging the fabric.
- Two people are recommended for mounting this product.
Warnings
- Do not use in bad weather conditions (e.g., rain, snow, frost).
- The product is not suitable for protection against rain, snow, or wind.
- Always use the product on a flat and level surface.
- Keep away from fire sources. Do not start a fire or barbecue in or around the product.
- This product is intended to protect the area below it from solar radiation and reduce reflections. Remove accumulated water or snow promptly to avoid frame overload.
- Do not place items on or lean on the product.
- Clean with a damp cloth and a neutral cleaner.
- Ensure the product is completely dry before storing to ensure service life.
- Keep small parts away from children during unpacking.
- Do not alter the design or configuration of the frame or safety devices, as this may result in a hazard.
Specifications
| Model | SDA200120 |
| Product Size | 78×47in |
| Color | Black |
Components
The following components are included:
- A1 (Φ37) × 1
- A2 (Φ37) × 1
- A3 (Φ35) × 2
- D1 (Φ25) × 1
- D2 (Φ25) × 1
- J × 1 (Awning Fabric)
- I × 1 (Roller Tube)
- Q × 12 (Screws/Fasteners)
- T1 × 2
- T2 × 2
- T3 × 2
- U × 2
- H × 2
- G × 4
- F × 2
- E × 1
- B1 × 2
- B2 × 2
- B3 × 2
- C1 × 2
- C2 × 2
- L × 1
- P × 1
- R × 2
- S × 1
- O × 1
- N × 2
- M × 2
- K × 2
Assembly Instructions
Step 1: Assemble Roller Tube
Connect tubes A1, A3, and A2 using fasteners (Q). The diagram shows A1 and A2 being joined by A3, with fasteners inserted.
Components used: A1×1, A2×1, A3×2, Q×8.
Step 2: Attach Fabric to Roller
Attach the awning fabric (J) to the roller tube (I). The diagram shows the fabric edge being inserted into a groove on the roller tube.
Components used: J×1, I×1.
Step 3: Insert Roller into Fabric Sleeve
Insert the assembled roller tube (A) into the sleeve of the awning fabric (J). The diagram shows tube A being slid into the fabric.
Components used: A×1 (assembled from A1, A2, A3), J×1.
Step 4: Prepare Awning Bar
Attach tubes D1 and D2 to tube D. Fasteners are inserted into the ends of D1 and D2 before connecting them to D.
Components used: D1×1, D2×1.
Step 5: Attach Awning Bar to Fabric
Attach the awning bar (D) to the bottom edge of the awning fabric (J). The diagram shows the fabric edge being secured to tube D.
Components used: D×1 (assembled from D1, D2), J×1.
Step 6: Attach Roller Assembly to Awning Bar
Connect the roller assembly (with fabric J) to the awning bar (D). Fasteners (Q) and component (L) are used to secure the roller to the awning bar.
Components used: J×1, D×1, Q×4, P×1, L×1.
Step 7: Assemble Support Brackets (Part 1)
Assemble the support bracket components. This involves connecting U, H, T1, T2, T3, and G. The diagram shows these parts being fitted together.
Components used: U×2, H×2, T1×2, T2×2, T3×2, G×4.
Step 8: Assemble Support Poles
Connect the main support poles B1 and B2. Attach component R to a pole. Attach C1 and C2 to B2. Attach E to B3. Attach S to B3. Attach O to a pole.
Components used: B1×2, B2×2, R×2, C1×2, C2×2, E×1, B3×2, S×1, O×1.
Step 9: Assemble Top Brackets
Assemble the top mounting brackets using components G, F, and B3. The diagram shows these parts being fitted together.
Components used: G×4, F×2, B3×2.
Step 10: Attach Roller End Caps
Attach components M, N, P, and O to the ends of the roller assembly. The diagram shows these parts being fitted onto the roller ends.
Components used: M×2, N×2, P×1, O×1.
Step 11: Attach Support Poles to Awning
Connect the support poles (with attached brackets) to the awning roller and awning bar. The diagram shows the poles being attached to the awning structure using components L, S, N, M, C, and K.
Components used: L×1, S×1, N×2, M×2, C×1, K×2.
Step 12: Final Mounting
Mount the assembled awning to the desired location (e.g., a house wall or balcony). The diagram shows the awning installed on a house.
Manufacturer and Importer Information
Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREET EASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
EU Representative: SHUNSHUN GmbH, Römeräcker 9 Z2021,76351 Linkenheim-Hochstetten, Germany
UK Representative: Pooledas Group Ltd, Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Made In: China
Contact Us â Official VEVOR Support
