Redtiger T700 User Manual
Version: V02
Email: support@redtigercam.com
Website: http://www.redtigercam.com
Phone: +188 8966 8028
Important Safety Information
Warning
Be careful when using your camera and its accessories. Always be cautious of your surroundings to avoid injuring yourself and others.
Make sure to follow all local laws including all privacy laws which may restrict recording in certain areas.
[Email Icon] [WhatsApp Icon] [Facebook Icon] [Line Icon]
Regulatory Information
IC Warning
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device must not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with IC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm from the radiator to your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
Déclaration de l'ISED Canada
Cet appareil contient des transmetteur(s)/récepteur(s) sans licence conformes aux normes RSS exemptes de licence d'Innovation, Sciences et Développement économique Canada. L'opération est sous réserve des deux conditions suivantes:
- Cet appareil ne peut pas causer d'interférences.
- Cet appareil doit accepter toute interférence, y compris celle susceptible de provoquer un fonctionnement indésirable de l'appareil.
Exposition aux rayonnements: Cet équipement est conforme aux limites d'exposition aux radiations du Canada pour un environnement non contrôlé. Pour maintenir la conformité avec les guides d'exposition RF d'IC, l'équipement doit être installé et actionné avec une distance minimale de 20cm entre le radiateur et votre corps. Cet appareil et ses antennes ne doivent pas être co-localisés ou utilisés en conjonction avec une autre antenne ou émetteur.
Maintenance
General Care
Do not directly plug and unplug the cable or SD card; please perform related operations after the camera is off.
Redtiger does not encourage connection with other hardwire kits. If necessary, ensure they are lower than 6V and higher than 3A.
Avoid prolonged exposure to direct sunlight. The camera may heat up during operation. Damage caused by high temperatures is covered by a 1-year free replacement warranty.
What's in the Box?
- T700 Mirror Dash Cam
- GPS Receiver
- Backup Camera Cable *1
- Car Charger *1
- 3M Sticker*1, Mount Bracket*1, Screws *4 (Inside of Vehicle)
- Backup Camera *1
- Straps *4
- User Manual*1
- Tool *1
- Cleaning Cloth *1
- Cable Straps*5
Mounting the Mirror
Step 1: Mount the Dash Cam
Pull out the lens of the T700 dash cam to match the rearview mirror of the vehicle.
Step 2: Secure the Dash Cam
Extend the straps around the back of the rear-view mirror and attach them to the bottom retaining hooks.
Step 3: Power Connection
Power on the dash cam using the included car charger. Do not use your own chargers.
Step 4: Test Functionality
Test the camera to ensure everything is working correctly.
Mounting the Rear Camera
Installation Location Recommendation
Redtiger recommends installing the rear camera outside the car, above the license plate. Installation inside the car may be affected by the windshield.
Installing Outside the Car
1. Tear off the 3M tape on the rear lens and paste it above the license plate.
Removing the Panel
Remove the inner panel of the trunk to expose the rear wiring compartment. Open the trunk and locate a sturdy inner panel covering the license plate area. Use a trim removal tool or thin device to pry it apart.
Routing the Cable
Use a trim removal tool to pop out tailgate trim, then run the cable from outside the car into the trunk.
Connecting Cables
Connect the rear camera's power cable to the extension cable. If you need to install a trigger cable to activate reversing guidelines, find the positive cable of the reversing lamp or consult a professional.
Installing Inside the Car
Step 1: Confirm Accessories
Verify you have: 1 mount bracket (2 black iron sheets), 4 screws (2 small, 2 large).
Step 2: Attach Bracket
Place an iron sheet over the rear camera, align with the hole, and screw it on.
Step 3: Secure Assembly
Join the two iron sheets together and tighten the screws.
Step 4: Final Mounting
Stick the bracket to the rear windshield using 3M glue.
Notes on Rear Camera Installation
Note:
- Installation outside the car provides a far better effect than inside.
- For RVs or pickup trucks, you can install the rear camera forward. Enable "Upside down of rear camera" and disable "Rear Cam" Mirror Image" in settings to adjust the image. A license plate bracket is also available upon request.
Mounting the GPS Module
How to Install the GPS
The GPS module has a front side that should face the sky. Tear off the protective paper to fix it.
Installation Location
Position 1: For optimal GPS signal reception, it is recommended to place the GPS module on the central console or near the edge of the front windshield, using double-sided tape after routing the wiring discreetly.
Redtiger recommends installing the GPS module at Position 1 for optimal use and convenience. Testing in other locations is also possible to find the most suitable spot.
Connecting and Activating GPS
(1) Install the GPS Antenna onto the camera. The GPS Antenna will begin searching for a GPS signal.
(2) Once the GPS is installed and a signal is received, the GPS icon will appear on the home screen, displaying direction and speed (requires "GPS Disp" to be enabled in settings).
Meet Your T700
Component Identification
| No. | Name | Description |
|---|---|---|
| 1 | Front Camera | Records the front view of the vehicle. |
| 2 | Power Supply Port | Connects to the car charger. |
| 3 | Rear Camera Port | Connects to the rear view camera. |
| 4 | MicroSD Card Slot | Insert a Micro SD card (maximum support 128GB). |
| 5 | GPS Port | Connects to the GPS receiver. |
| 6 | Fasteners | Use the included silicone straps. |
| 7 | Screen | 11-inch IPS touch screen. |
| 8 | Power Button | Short press to turn off the screen; long press to turn off the power. |
Power Options
1. Cig Charger
It is best to use the power cord that comes with the product or Redtiger's professional hardware kits.
2. Hardwire Kit
Note: Not included, needs to be purchased separately.
Setting Up Your Camera
On-Screen Interface Icons
The display shows:
- Speed & Driving Direction: Displays when GPS is connected.
- Screen Brightness Adjustment: Slide the bar left/right to adjust brightness.
- Settings: Touch to enter the menu.
- File Playback: Playback videos and photos.
- Start/Stop Recording: ? to begin or end recording.
- Front/Rear View Switch: Switch between front and rear camera views.
- Snapshot: ? to take a still image.
- Emergency Lock: Locks videos as event files, preventing overwriting by loop recording.
- Date & Time: Displays current date and time.
- Recording Status: Yellow flashing indicates Lock Recording.
- SD Card Status: Shows the status of the inserted SD card.
- Audio Record: Indicates if audio recording is active.
- Loop Time: Adjust loop recording duration (1 Min / 2 Min / 3 Min).
Adjusting View and Brightness
While recording, swipe the screen up and down to adjust the angle of view.
Swipe the screen left or right to switch between front view, rear view, or split-screen view.
Touch the touchscreen to display the brightness scrollbar at the upper center, then slide left or right to adjust brightness.
SD Card Installation
With the camera off, insert the SD card into the slot with the label facing the back. Eject the card by pressing it into the slot with your fingernail.
Wiring Setup
Connect your camera to a Cig charger using the included cable.
A micro SD card (sold separately) is required for saving videos and photos. Use a U3 Class 10 SD Card; otherwise, the camera may malfunction.
SD cards can degrade over time. If experiencing issues, try swapping to a new card.
Customizing Your T700
Power ON/OFF
When the engine starts (ACC on) with the cigar power adapter connected, the unit powers on automatically and displays the opening screen.
To turn off the power during startup, press and hold the power button. Briefly press it again to turn the unit on and display the opening screen.
Briefly press the power button to turn off the screen.
Menu Settings
After powering on the camera, press the ? to pause recording, then press the ⚙️ to enter the setup process.
Video Settings
| Function | Function Description | Function Options |
|---|---|---|
| Rear camera brightness adjustment | Adjust the brightness of the rear camera. | High/Middle/Low |
| Resolution | Adjust the video recording resolution. | 2160P+1080P, 1440P+1080P, 1080P+1080P |
| Movie Clip Time | Adjust the loop recording duration. | 1 minute / 2 minutes / 3 minutes |
| Sound Record | Turn On/Off audio recording. | On/Off |
System Settings
| Function | Function Description | Function Options |
|---|---|---|
| Time always on | When turned off, the time is not displayed in the recording interface. | On/Off |
| Language | Set the common language. Default is English. | English/Deutsch/Français/Italiano/Português/简体中文/繁體中文/日本語/한국인/Latviešu |
| Flicker | Adjusts for local power frequency. | 50Hz / 60Hz |
| Screen saver | Set the screen display status when recording. | Off: Screen always on. 1min/2min/3min: Automatically close the screen. |
Advanced Settings
| Function | Function Description | Function Options |
|---|---|---|
| G-Sensor sensitivity | Adjust the sensitivity of the G-sensor. Recommended setting: "Low". | Off/Low/Medium/High |
| Default booting display | Sets the initial display mode on the screen. | Split Screen / Front camera / Rear camera |
| Volume setting | Adjust the volume. | / |
| Clock Settings | No manual setting needed by default. If manual adjustment is required, turn off GPS for automatic time setting. | / |
Time and Speed Settings
| Function | Function Description | Function Options |
|---|---|---|
| Time style | Sets the time format. | 24H Time style / 12H Time style |
| Time zone | Set the time zone. | UTC -08:00 (Example) |
| Speed Unit | Set the vehicle speed display mode. | KM/H / MPH |
| Forced recording | Ensures recording starts automatically if you navigate away from the recording interface. | On/Off |
Recording Options
| Function | Function Description | Function Options |
|---|---|---|
| Locked video loop | Loop recording overwrites normal unlocked video. Enable this to also lock videos that are covered. | On/Off |
| Daylight Saving Time | Enable/disable Daylight Saving Time. | On/Off |
| Mirror flip of rear image | Flip the rear camera image horizontally. | On/Off |
| Upside down of rear image | Flip the rear camera image vertically (up and down). | On/Off |
Mirror Flip and Upside Down Image
The device allows flipping the rear camera image horizontally ("Mirror flip of rear image") and vertically ("Upside down of rear image") for optimal viewing.
System Management
| Function | Function Description | Function Options |
|---|---|---|
| Format SD-Card | This feature formats the inserted memory card, deleting all data. | OK/Cancel |
| Reset Setup | Resets all settings to default. | OK/Cancel |
| Show reversing line | Enable/disable the display of reversing guidelines. | On/Off |
| Reversing line | Adjust the reversing line position and angle. | / |
Reversing System Notes
Note:
If your car lacks a reversing system, connect the rear camera's red cable to the positive pole of your reversing lamp. If your car already has a reversing system, ignore the rear camera's red cable.
When shifting to "R" gear, the rear view will display with reversing lines for easier parking. Access "Reversing line" in settings to adjust the image and line angle. The viewing angle can also be adjusted during reversing. This function activates after connecting the rear camera's red wire to the reversing light's positive pole.
Information
| Function | Function Description | Function Options |
|---|---|---|
| GPS Information | Check GPS signal reception details (Number, Time, Longitude, Latitude). | / |
| Product Information | Check the product model and firmware version. | / |
Playback Mode
When the dash cam powers on, it starts recording automatically. Press the ? to pause recording and enter playback mode.
Playback Menu Options
- 1. Loop recording files: Access files recorded in loop mode.
- 2. Locked video files: Access files locked by the emergency recording function.
- 3. Snapshot files: Access captured still images.
- 4. Switch front/rear video list: ↔️ to switch between viewing front and rear camera file lists.
- 5. List of video files: View all recorded video files.
- 6. Play/Pause: Control video playback.
- 7. Delete specified file: Remove a selected file.
- 8. Lock/Unlock specified file: Manually lock or unlock a file.
- 9. View videos on fullscreen: Expand the video to full screen.
Caution
Front-view and rear-view videos are displayed in separate lists. Use the provided icon ↔️ to switch between them.
Redtiger Player (PC)
Download GPS Player
Download the GPS Player from the official website: https://www.redtigercam.com/pages/gps-player
Transferring Recordings
Transfer your recordings to a computer.
Drag and drop the files into the GPS Player application.
Using the GPS Player
The player allows you to view footage, track your route on a map, see speed and location data, and choose to view front or rear camera feeds.
You can watch front and rear footage simultaneously.
Customer Service
Words from Heart
Redtiger is committed to producing the best product quality and high-quality after-sales support, prioritizing customer safety.
The company believes its character is defined by its actions when products don't meet expectations. Redtiger offers a 1-month free return, a 1-year limited warranty, and lifetime technical support. Products are guaranteed free from defects in materials and workmanship from the date of purchase. Customers can also exchange a 1-year-old product at a discounted price by contacting them online.
Redtiger Customer Service Team is available to listen to advice and address any problems.
Contact Information
Email:
- Mirror Dash Cam: support@redtigercam.com
- Mini Dash Cam: help@redtigercam.com
- Business Cooperation or Others: contact@redtigercam.com
Customer Phone Service: +1 888 966 8028
Product Information
| Item | Details |
|---|---|
| Item Name | 11" Stream Media Dash Camera |
| Model | REDTIGER T700 |
| Screen Size | 11" IPS Touch Screen |
| Power Interface | Type C 5V/3A |
| Battery | Super Capacitor |
| Recording Resolution | Front Camera: 3840*2160P, 2560*1440P, 1920*1080P Rear Camera: 1920*1080P |
| Loop recording | 1/2/3 mins |
| Recording method | Normal Recording / Emergency Recording |
| Screen View | Front + Rearview / Front view / Rearview |
| Video Format | Video: TS; Still image: JPG |
| Memory Card | Micro SD card 32G ~ 256G |
| GPS | Yes |
| G-sensor | Yes |
| Audio | Support sound recording and playback |
| Operating Temperature | -4°F ~ 158°F |
About Us
In the era of automobile interconnection, every aspect of the driving experience is within reach.
Product and service are the foundation of Redtiger. The company has an expert research and development team of "self-driving experts".
Based on personal user needs, Redtiger uses technology to drive product innovation. In the future, Redtiger will continue to explore technological boundaries to open up a broader vision for driving.
