Fanttik NEX K2 Ultra Brushless Cordless Drill

1. Safety Warnings

• Avoid moisture, dust, and drops.
• Do not store the product in extreme temperature environments.
• Stay alert, watch what you are doing, and use common sense when operating. Do not operate while you are tired or under the influence of drugs, alcohol, or medication.
• This product is not a toy and should not be used by children under 12 years old.
• This product has a built-in battery; do not throw it into fire and ensure it is recycled according to local laws and regulations.
• Do not dismantle the machine yourself. Have your power tool serviced by a qualified repair person or contact Fanttik customer support for advice.

2. Package Contents

Illustration showing the contents of the package.

• Cordless drill x 1
• Screwdriver bits x 10
• All-in-One Storage stand x 1
• Wood drill bits x 5
• Metal drill bits x 5
• Storage bag x 1
• USB-C charging cable x 1
• User Manual x 1
• Quick start guide x 1

3. Product Overview

Diagram of the Fanttik NEX K2 Ultra cordless drill and its storage stand, with numbered parts.

Key Components

• 1. Keyless chuck
• 2. LED work light
• 3. Side display
• 4. Side button
• 5. Variable speed trigger
• 6. Torque/Speed control knob
• 7. Main display
• 8. Function button
• 9. Type-C charging port
• 10. All-in-One storage stand
• 11. 360° swivel arm
• 12. Push-open bit storage compartment

4. Operation and Functions

Installing and Removing a Bit

Illustration showing a drill bit being inserted into the chuck.

Install

Rotate the chuck sleeve counterclockwise sufficiently to accept the desired screwdriver bit or drill bit. Insert the bit deep into the chuck and tighten securely by grasping and rotating the chuck sleeve clockwise until firmly in place.

Remove

Hold the tool with one hand and rotate the chuck sleeve counterclockwise to loosen the chuck, then remove the bit.

Variable Speed Trigger

Close-up illustration of the variable speed trigger.

Press the trigger to turn on the device. The Variable Speed Trigger controls the motor speed. The farther the trigger is depressed, the higher the working speed.

Side Button (Direction and Child/Transportation Safety Button)

Sequence of illustrations showing the side button's function: locking the motor (lock symbol), unlocking the motor, and switching rotation direction (forward/reverse arrow symbols).

• Press and hold the Side Button for two seconds to lock the tool motor for child safety or transportation safety. A lock symbol ? appears on the Side Display.
• In motor lock mode, press and hold the Side Button for two seconds to unlock the motor.
• In unlock mode, briefly press the Side Button to switch the motor's rotate direction. A corresponding forward ➡️ or reverse ⬅️ arrow symbol will appear on the Side Display.

TapSwitch™ One Press Gear Shift & Working Modes

Illustration of the function button and a circular icon representing gear modes.

The tool has two regular modes: screwdriver mode and drill mode. Short press the Function Button to switch between them. When pressed, the device will automatically shift gears, producing an audible gear-shifting sound. (Occasionally, the gear may shift two or three times, which is normal.) Avoid pressing the button repeatedly; wait for the device to finish shifting gears before switching modes.

Working Modes & UI

In screwdriver mode: A screw symbol and the current torque setting appear on the display. The maximum torque can be adjusted from 1 to 30 N·m (8.9 to 265 in-lb) by rotating the Torque/Speed Control Knob. Available torque settings are 1, 2, 3... 18, 19, 20, and 30 (a total of 21 torque settings). The speed is controlled by the Variable Speed Trigger, with a maximum unloaded speed of 500 RPM.

In drill mode: A drill bit symbol and the maximum speed limit will appear on the display. The knob adjusts the maximum speed limit, with settings of 500, 800, and 1250 RPM. You can select a lower speed limit for drilling hard materials or large holes, and a higher speed limit for drilling soft materials or small holes.

Illustrations of the main display showing different speed settings in Screwdriver Mode (010 Nm, 015 Nm, 020 Nm, 030 Nm) and Drill Mode (500 RPM, 800 RPM, 1250 RPM).

AutoAssist Function

Illustrations of the main display showing 'AU' symbol for Screwdriver AutoAssist and Drill AutoAssist.

The tool features AutoAssist. Long press the Function Button for 2 seconds to activate this function, and long press again to deactivate it. When activated, 'AU' and a corresponding symbol (e.g., screw or drill bit) will appear on the display to indicate whether you are in screwdriver Auto Assist mode or drill Auto Assist mode. You can switch between the two Auto Assist modes by short pressing the Function Button.

In screwdriver AutoAssist mode, the tool automatically halts when the screw is fully tightened, ensuring precise screw driving without over-tightening. (The final effect may be affected by different types of wood and sizes of self-tapping screws. It is also possible that the feature may be triggered during screw driving. A recommended condition is driving M4 x 30mm self-tapping screws into pine wood).

In drill AutoAssist mode, the tool automatically adjusts the maximum power output.

LED Work Light

Illustration showing the LED work light at the front of the drill.

The LED work light automatically turns on when the Variable Speed Trigger is pressed. The LED light remains on for 10 seconds after the trigger is released.

5. Power Indicator & Battery Charging

Power Indicator

Illustration of the drill's display showing the battery level indicator.

The battery symbol on the display shows the current battery level. When it is empty, charge the tool promptly. During charging, the green arc bar and battery symbol flash. Once fully charged, the battery symbol and green arc bar remain solid.

Battery Charging

Illustration showing the Type-C charging port on the drill.

This tool is equipped with a universal Type-C charging port and includes a USB charging cable. A charger is not included; please use a 5V charger for charging. The screwdriver supports a maximum charging input of 10W (5V/2A).

6. Specifications

Table listing the technical specifications of the Fanttik NEX K2 Ultra Brushless Cordless Drill.

7. Bit Specifications

Screwdriver Bit Specifications and Type

• Bit Shank: 1/4-inch (6.3mm) hex shank
• Bit Length: 2" (50mm)
• Phillips: PH1, PH2
• Slotted: SL4.0, SL6.0
• Hex: H4, H5, H6
• Tamper-Resistant Torx: TR15, TR20, TR25

Drill Bit Type

• Wood drill bit: 1/8", 5/32", 13/64", 15/64", 5/16"
• Metal drill bit: 5/64", 1/8", 5/32", 13/64", 15/64"

8. Warranty Card

Your Warranty Includes

• Your product is covered for 12 months against manufacturing defects.

How to Return Your Fanttik Product

• Email Fanttik customer support at support@fanttik.com with your order number.
• Fanttik will email you a prepaid return shipping label.
• Tear off the 'Return Details' page, fill it out, and include it inside your return package.
• Use the provided label to ship your package back to Fanttik.
• Once shipped, email Fanttik. They will expedite your replacement or solution.

Return Details

Complete this section and include it in your package for faster processing: