SKF Automatic Lubricators
Automatic lubricators deliver safety, reliability and efficiency
Manual Lubrication vs. Automatic Lubrication
Performing manual lubrication tasks can be challenging due to the vast number of lubrication points throughout a factory. Also, most of these points have varying lubrication requirements. Utilising automatic lubricators is one solution that can improve worker safety and increase machine reliability.
Reduce the risks of failure
Over-greased: overheating, waste and pollution
Optimal lubrication
Under-greased: wear, premature repairs, high repair costs
[Graph Description: A line graph comparing manual and automatic lubrication levels over time. The red line (Manual lubrication) shows significant fluctuations between over-lubrication and under-lubrication. The blue line (Automatic lubrication) shows a stable, optimal lubrication level.]
Challenges associated with manual lubrication
Manual lubrication tasks can be complex and inconvenient, often requiring equipment shutdown. Manual lubrication on difficult-to-access lubrication points also can increase the possibility of worker injury and take your valuable human resources away from other tasks.
Improper manual lubrication can be a factor in creating additional challenges. Failure to lubricate every lubrication point regularly can have a negative effect on equipment reliability, production schedules and maintenance efficiency. Other results of improper manual lubrication can be lubricant waste, environmental issues, increased energy consumption and finished product spoilage due to contamination of lubricant.
Benefits of using automatic lubricators
A lubricator is designed to automatically supply a small quantity of clean grease or oil to a lubrication point on a regular basis, thus improving bearing performance. Key benefits of using an automatic lubricator are improved employee safety, increased machine reliability and optimized maintenance operations.
SKF SYSTEM 24 lubricators are suitable for a variety of applications but often are used on pumps, electric motors, fans, blowers, conveyors and chains. They can be adjusted to ensure that the correct quantity of lubricant is delivered to the lubrication point during a predetermined period of time. This provides a more accurate control of the amount of lubricant supplied, when compared to traditional manual lubrication techniques.
Improving Employee Safety
Use of SKF SYSTEM 24 lubricators can have a positive impact on workplace safety because technicians can spend less time in confined spaces, with safety cages or guards removed, and on rooftop or elevated lubrication tasks.
Lubrication point behind safety guards
Safety cages and guards are utilised for a reason – to protect workers and others from injury caused by moving parts. By reducing the amount of time these implements are not in place, SKF SYSTEM 24 lubricators increase safety and eliminate the need to manually lubricate difficult-to-access lubrication points.
Elevated lubrication point
Lubrication points on rooftops or other high elevations can create a significant challenge, and the safety implications are evident. Due to apprehension, these lubrication points often are not lubricated properly and equipment reliability suffers.
Manual handling of lubricants
Improper handling of loose lubricant can expose technicians to chemicals. By eliminating manual handling of lubricant, SKF SYSTEM 24 lubricators reduce the potential for chemical exposure of workers.
Machine Reliability
The importance of lubrication often is overlooked due to its underestimated impact on equipment total cost of ownership. However, machine reliability can be enhanced substantially with proper lubrication. As the leading supplier of bearings worldwide, SKF has conducted extensive research and determined that up to 50 percent of premature bearing failures are due to either improper lubrication practices or contamination.
Premature bearing failure
Approximately 36 percent of premature bearing failures are due to improper lubrication, such as too much, too little or the wrong type of lubricant. Another 14 percent of bearing failures occur because of contamination via poor seals or lubricant handling practices.
[Pie Chart Description: Causes of premature bearing failure: Fatigue 34%, Poor lubrication 36%, Poor fitting 16%, Contamination 14%.]
Clean, fresh lubricant
A continuous supply of clean, fresh grease or oil is essential when lubricating equipment. SKF SYSTEM 24 lubricators feature high quality SKF lubricants in a water- and dust-resistant design.
Positive pressure
Positive pressure prevents contaminants from entering the bearing through the seal. SKF SYSTEM 24 lubricators can provide fresh lubricant and purge seals of smaller-sized bearings operating at lower speeds, while larger bearings may benefit from a separate lubricator for lubrication and seal purging.
Missed lubrication points
With manual lubrication, it is difficult and time consuming to find every lubrication point. Use of SKF SYSTEM 24 lubricators helps to ensure that each point is receiving the proper amount of lubricant on a set schedule.
Supporting Effective Maintenance
The use of automatic lubricators can have a large impact on effective maintenance. The most significant benefits usually are found in the reduction of unplanned downtime, machine repair costs, labor and lubricant consumption.
[Bar Chart Description: Comparison of Manual vs. Automatic Lubrication costs for SKF SYSTEM 24. Automatic lubrication shows significant improvements (reductions) in SKF SYSTEM 24 investment, Lubricant consumption, Lubrication labour, Machine repair costs, Planned downtime, and Unplanned downtime.]
Improved machine reliability
Using an SKF SYSTEM 24 lubricator provides increased machine reliability and, therefore, reduces unplanned downtime.
Increased productivity
Because automatic lubricators deliver lubricant while the equipment is in operation, there is less scheduled downtime and more productivity.
Better use of personnel
Automatic lubrication enables workers to focus on more value-added tasks, such as machine inspection.
Lower cost of ownership
Improved equipment reliability and performance means lower machine repair costs.
SKF SYSTEM 24
Gas driven single point automatic lubricators: SKF LAGD series
The units are supplied ready-to-use straight from the box and filled with a wide range of high performance SKF lubricants. Tool-free activation and time-setting allow easy and accurate adjustment of lubrication flow.
- Flexible dispense rate from 1 to 12 months
- Stoppable or adjustable if required
- Intrinsic safety rating: ATEX approved for zone 0
- Transparent lubricant container allows visual inspection of dispense rate
- Compact size, permits installation in restrictive areas
- Greases and chain oils available
Typical applications
- Applications in restrictive and hazardous locations
- Bearing housing lubrication
- Electric motors
- Fans and pumps
- Conveyors
- Cranes
- Chains (oil)
- Elevators and escalators (oil)
[Diagram Description: Components of the LAGD series lubricator: Easy-grip top-cover (Specially designed top ring for an optimum grip), Toolless dial (Allows easy and accurate adjustment of flow rate), Gas cell (Detachable batteries for an environmentally friendly disposal), Piston (Special piston shape helps ensure optimum emptying of lubricator), Lubricant container (Transparent lubricant container allows visual inspection of dispense rate), SKF Lubricants (Filled with high quality SKF lubricants).]
Ordering details
| Grease | Description | Unit 60 ml | Unit 125 ml |
| LGWA 2 | High load, extreme pressure, wide temperature range | LAGD 60/WA2 | LAGD 125/WA2 |
| LGEM 2 | High viscosity bearing grease with solid lubricants | LAGD 60/EM2 | LAGD 125/EM2 |
| LGGB 2 | Biodegradable | – | LAGD 125/GB2 |
| LGHB 2 | High load, high temperature, high viscosity | LAGD 60/HB2 | LAGD 125/HB2 |
| LGHQ 2 | High load, high temperature, high viscosity | LAGD 60/HQ2 | LAGD 125/HQ2 |
| LGWM 2 | High loads, wide temperature | – | LAGD 125/WM2 |
| LGFG 2 | General purpose food grade (NSF H1) | LAGD 60/FG2 | LAGD 125/FG2 |
| LGFQ 2 | High load and wide temperature food grade (NSF H1) | – | LAGD 125/FQ2 |
| Chain oils 1) | |||
| LHMT 68 | Medium temperature | LAGD 60/HMT68 | LAGD 125/HMT68 |
| LHHT 250 | High temperature | – | LAGD 125/HT250 |
| LFFM 100 | General purpose food grade (NSF H1) | – | LAGD 125/FM100 |
| LFFT 220 | High temperature food grade (NSF H1) | – | LAGD 125/FT220 |
| Empty unit | Empty unit suitable for oil filling only | LAGD 60/U | LAGD 125/U |
1) Includes non-return valve
Technical data
| Designation | LAGD 60 and LAGD 125 | Intrinsically safe approval | II 1G Ex ia IIC T6 Ga II 1D Ex ia IIIC T200 85°C Da I M1 Ex ia I Ma |
| Grease capacity | LAGD 60: 60 ml (2 US fl. oz) LAGD 125: 125 ml (4.2 US fl. oz) | EC Type examination certificate | DEKRA 21ATEX0015 X |
| Nominal emptying time | Adjustable; 1-12 months | Protection class | IP 68 |
| Ambient temperature range | -20 to +60 °C (−5 to +140 °F) | Recommended storage temperature | 20 °C (70 °F) |
| Maximum operating pressure | 5 bar (75 psi) (at start-up) | Storage life of lubricator | 2 years |
| Drive mechanism | Gas cell producing inert gas | Weight | LAGD 60: approx 130 g (4.6 oz) LAGD 125: approx 200 g (7.1 oz) |
| Connection thread | R1/4 | Lubricant included | Lubricant included |
| Maximum feed line length with: grease oil | 300 mm (11.8 in.) 1 500 mm (59.1 in.) |
Note: If ambient temperature is constant between 40 °C and 60 °C (105 °F and 140 °F), do not select a setting of more than 6 months for optimum performance.
Electro-mechanical single point automatic lubricators: SKF TLSD series
The SKF TLSD series is the first choice when a simple and reliable automatic lubricator is required under variable temperatures, or when the application conditions (such as vibration, limited space or hazardous environments) require a remote mounting.
- Filled with SKF Lubricants especially developed for bearing applications
- Maximum discharge pressure of 5 bar over the whole dispensing period
- Transparent reservoir allows visual inspection
- The drive unit can be programmed to dispense lubricant in 1, 2, 3, 4, 6, 8, 9, 10 and 12 month settings
- The drive unit can be used with both cartridge versions by adjusting the 125/250 ml switch
- Traffic light LEDs are visual from all sides because of the presence of dual LEDs on the sides of the lubricator.
- Suitable for both direct and remote installation
- Complete sets are supplied ready to use, including drive unit, battery pack, cartridge with lubricant and support plate
- Cartridge sets include battery pack
Typical applications
- Critical applications where extreme reliability and additional monitoring is required
- Applications in restrictive and hazardous locations
- Applications requiring high volumes of lubricant
Multiple accessories are available for TLSD lubricators (see pages 14-15).
SKF DialSet helps to calculate the correct dispense rate (see page 16).
[Image Description: SKF TLSD series lubricators. One image shows the Drive unit - TLSD 1-DS with its electric drive and time setting wheel. Another shows a Cartridge set, e.g., LGWA 2/SD125, which is a replaceable canister filled with grease or oil and includes a battery pack. A Support plate is also mentioned.]
Cabled drive unit TLSD 1-DK
For applications that are occasionally in operation
An alternative to the battery powered drive unit is the cabled drive unit. This unit is cable connected to enable direct power supply and signal transfer. Supplied with plastic cap and support plate for grease lubrication. Lubricant cartridges are available separately.
- Possibility to lubricate only when the equipment is running
- Direct power supply
- Control and monitoring connection to the machine PLC
- For detailed information, see publication PUB MP/P8 19151 EN
[Image Description: The cabled drive unit TLSD 1-DK for the SKF SYSTEM 24 automatic lubricator.]
Ordering details
| Grease | Description | Complete unit 125 | Complete unit 250 | Cartridge set 125 | Cartridge set 250 |
| LGWA 2 | High load, extreme pressure, wide temperature range | TLSD 125/WA2 | TLSD 250/WA2 | LGWA 2/SD125 | LGWA 2/SD250 |
| LGEM 2 | High viscosity bearing grease with solid lubricants | TLSD 125/EM2 | TLSD 250/EM2 | LGEM 2/SD125 | LGEM 2/SD250 |
| LGHB 2 | High load, high temperature, high viscosity | TLSD 125/HB2 | TLSD 250/HB2 | LGHB 2/SD125 | LGHB 2/SD250 |
| LGHQ 2 | High performance, high temperature | TLSD 125/HQ2 | TLSD 250/HQ2 | LGHQ 2/SD125 | LGHQ 2/SD250 |
| LGFG 2 | General purpose food grade (NSF H1) | TLSD 125/FG2 | TLSD 250/FG2 | LGFG 2/SD125 | LGFG 2/SD250 |
| LGFQ 2 | High load and wide temperature food grade (NSF H1) | – | – | LGFQ 2/SD125 | LGFQ 2/SD250 |
| Chain oils | |||||
| LHMT 68 | Medium temperature oil | TLSD 125/HMT68 1) | TLSD 250/HMT68 1) | LHMT 68/SD125 2) | LHMT 68/SD250 2) |
| LFFM 100 | General purpose food grade (NSF H1) | – | – | LFFM 100/SD125 2) | LFFM 100/SD250 2) |
1) Includes support plate with non-return valve.
2) Support plate with non return valve (TLSD 1-SPV) can be ordered separately.
Technical data
| Designation | TLSD 125/... and TLSD 250/... | ||
| Grease capacity | TLSD 125: 125 ml (4.2 US fl. oz) TLSD 250: 250 ml (8.5 US fl. oz) | Protection class assembled lubricator | IP 65 |
| Emptying time | User adjustable: 1, 2, 3, 4, 6, 8, 9, 10 and 12 months | Battery pack TLSD 1-BAT | 4,5 V 2,7 Ah/Alkaline manganese |
| Lowest grease purge | TLSD 125: 0,3 ml (0.01 US fl. oz) per day TLSD 250: 0,7 ml (0.02 US fl. oz) per day | Recommended storage temperature | 20 °C (70 °F) |
| Highest grease purge | TLSD 125: 4,1 ml (0.13 US fl. oz) per day TLSD 250: 8,3 ml (0.28 US fl. oz) per day | Storage life of lubricator | 3 years 2) (2 years for food grade lubricants and oils) |
| Ambient temperature range TLSD 1-BAT | 0 to 50 °C (30 to 120 °F) | Total weight (incl. packaging) | TLSD 125: 635 g (22.5 oz) TLSD 250: 800 g (28.2 oz) |
| Maximum operating pressure | 5 bar (75 psi) | ||
| Drive mechanism | Electro mechanical | ||
| Connection thread | G 1/4 | ||
| Maximum feed line length with: grease oil | Up to 3 meters (10 ft) 1) Up to 5 meters (16 ft) |
| LED status indicators | TLSD 1-DS | TLSD 1-DK | |
| Green OK | each 30 sec | each 3 sec | |
| Yellow Warning, high back pressure | each 5 sec | each 1 sec | |
| Warning, low battery power | each 30 sec | – | |
| Warning, cartridge almost empty | – | each 3 sec | |
| Red Alarm, high back pressure | each 2 sec | each 1 sec | |
| Alarm, empty cartridge | each 5 sec | each 3 sec | |
| Alarm, error in lubricator | each 5 sec | each 5 sec |
1) The maximum feed line length is dependent on ambient temperature, grease type and back pressure created by the application.
2) Maximum storage life is 3 years from production date, which is printed on the side of the canister. The canister and battery pack may be used at 12 month setting even if activated 3 years from production date.
Electro-mechanical single point automatic lubricators: SKF TLMR series
The SKF Automatic Lubricant Dispenser – TLMR – is a single point automatic lubricator designed to supply grease to a single lubrication point. With a relatively high pressure of 30 bars, this lubricator can operate at long distances providing optimum results with difficult-to-reach and unsafe lubrication locations. With a wide temperature range and robust design, the TLMR lubricator is suitable for operating conditions with various levels of temperature and vibration.
- Filled with high quality SKF greases
- Temperature independent dispense rate
- Extended time setting up to 24 months
- Maximum discharge pressure of 30 bar over the whole dispensing period
- Available in two versions: TLMR 101 powered by batteries (standard Lithium AA type) and TLMR 201 powered by 12–24 V DC
- Available with non-refillable cartridges in two sizes: 120 and 380 ml
Typical applications
- Applications requiring high lubricant consumption
- Applications experiencing high vibration in operation
- Excellent water and dust protection makes TLMR suitable for general machinery applications and food processing machinery
- Excellent high temperature performance makes TLMR suitable for engine rooms and hot fan applications
- Excellent low temperature performance makes TLMR suitable for wind turbine applications
Multiple accessories are available for TLMR lubricators (see pages 14-15).
SKF DialSet helps to calculate the correct dispense rate (see page 16).
[Image Description: The SKF TLMR series automatic lubricant dispenser. It is shown mounted with a strong bracket. Another image highlights the ease of exchanging cartridges by screwing them in.]
Ordering details
| Grease | Description | TLMR 101 refill sets (cartridge and battery) | TLMR 201 cartridges | ||
| 120 ml | 380 ml | 120 ml | 380 ml | ||
| LGWA 2 | High load, extreme pressure, wide temperature range bearing grease | LGWA 2/MR120B | LGWA 2/MR380B | LGWA 2/MR120 | LGWA 2/MR380 |
| LGEV 2 | Extremely high viscosity bearing grease with solid lubricants | – | LGEV 2/MR380B | – | LGEV 2/MR380 |
| LGHB 2 | High load, high temperature, high viscosity bearing grease | – | LGHB 2/MR380B | – | LGHB 2/MR380 |
| LGHQ 2 | High performance, high temperature bearing grease | – | LGHQ 2/MR380B | – | LGHQ 2/MR380 |
| LGFG 2 | General purpose food grade (NSF H1) bearing grease | – | LGFG 2/MR380B | – | LGFG 2/MR380 |
| LGWM 1 | Extreme pressure, low temperature bearing grease | – | LGWM 1/MR380B | – | LGWM 1/MR380 |
| LGWM 2 | High load, wide temperature range bearing grease | – | LGWM 2/MR380B | – | LGWM 2/MR380 |
| LGEP 2 | Extreme pressure bearing grease | – | LGEP 2/MR380B | – | LGEP 2/MR380 |
| LGMT 3 | All purpose industrial and automotive bearinggrease | – | LGMT 3/MR380B | – | LGMT 3/MR380 |
| Complete sets | TLMR pump | |||
| TLMR 101/38WA2 | Lubricator with 380 ml cartridge filled with LGWA 2 grease, powered by batteries. | TLMR 101 | Lubricator powered by batteries | |
| TLMR 201/38WA2 | Lubricator with 380 ml cartridge filled with LGWA 2 grease, powered by 12–24 V DC | TLMR 201 | Lubricator powered by 12–24V DC, plug M12-A (not included) | |
Technical data
| Designation | TLMR 101 and TLMR 201 | Drive mechanism | Electro mechanical |
| Grease capacity | 120 ml (4.1 US fl. oz) 380 ml (12.8 US fl. oz) | Connection thread | G1/4 female |
| Emptying time | User adjustable: 1,2,3,6,9,12, 18, 24 months or purge | Maximum feed line length 1) | Up to 5 meters (16 ft) |
| Lowest setting | 120 ml cartridge: 0,16 ml (0.005 US fl. oz) per day 380 ml cartridge: 0,5 ml (0.016 US fl. oz) per day | LED status indicators | |
| Highest setting | 120 ml cartridge: 3,9 ml (0.13 US fl. oz) per day 380 ml cartridge: 12,5 ml (0.42 US fl. oz) per day | Green LED (every 8 sec) | OK |
| Purge | 31 ml (1 US fl. oz) per hour | Green and red LED (every 8 sec) | Almost empty |
| Ambient temperature range | –25 to +70 °C (−13 to +158 °F) | Red LED (every 8 sec) | Error |
| Maximum operating pressure | 30 bar (435 psi) | ||
| Protection class | IP 67 DIN EN 60529 DIN 40 050 Teil 9 | ||
| Power | TLMR 101: 4 AA Lithium batteries TLMR 201: 12–24 Volt DC via M12-A connection |
1) The maximum feed line length is dependent on ambient temperature, grease type and back pressure created by the application.
Ready-to-use centralised lubrication system
SKF TLMP series
The SKF MultiPoint Automatic Lubricator TLMP series is intended for reliable relubrication of multiple lubrication points. This sturdy automatic lubrication system is packaged as a complete kit, including the lubricator, required tubing and connectors. Designed to supply from one to eighteen lubrication points, the TLMP series features pluggable outlets and is easy to install and program via its keypad with LED display.
Featuring a reservoir capacity of nearly one litre, this versatile lubricator has a stirring paddle to prevent grease separation, making it suitable for more lubricants. With its high IP protection rating, the durable TLMP series is vibration resistant, withstands equipment washdowns and prevents contamination ingress. Also, the unit enables machine steering to temporarily disable lubrication by removing power.
TLMP series advantages
- Easy to install and program
- Complete kit
- Suitable for one to eighteen lubrication points
- Low-level and malfunction alarms; remote notification possible
- Machine steering by removing power
- Available in versions with different voltages
- Developed for industrial applications, as well as agricultural and off-road vehicles
[Image Description: The SKF TLMP series multi-point automatic lubricator. The text describes it as a complete kit for reliable relubrication of multiple points, with a large reservoir and robust design.]
[Diagram Description: Components of the TLMP series lubricator: Filter to avoid grease contamination from airborne particles, Stirring paddle to prevent grease separation, Durable, metal housing for long service life, Grease nipple, Pump element features maximum operating pressure of 205 bar (2 970 psi), LED display for simple programming, Divider block provides flexibility of using one to eight outlets, Cycle control sensor ensures lubricant is delivered to outlets, Alarm indicates when reservoir is empty or when outlet is blocked.]
[Diagram Description: Accessories for the TLMP series: Filler nipple (Replaces standard grease nipple for quicker lubricant replenishment using filler pump. LAGF 1-H) and Flexible hose with filler nipple (Replaces standard grease nipple for quicker lubricant replenishment using filler pump. LAGF 1-F).]
The TLMP series are supplied complete with the following items
| TLMP 1008 | TLMP 1018 | ||
| 1 x | 1 x | Pump | |
| 1 x | 1 x | Fitting material for the pump unit | |
| 2 x | 2 x | Electrical connectors | |
| 20 m (65 ft) | 50 m (164 ft) | plastic pipe Nylon, 6 x 1,5 mm | |
| 8 x | 18 x | Straight tube connectors for application G1/8 | |
| 8 x | 18 x | Tube connectors plugs | |
| 7 x | 17 x | Outlet closure plugs |
Technical data
| Designation | TLMP 1008 and TLMP 1018 | External steering | By disconnecting power supply |
| Number of lubrication outlets | TLMP 1008: 1–8 TLMP 1018: 1–18 | Ambient temperature | –25 to +70 °C (−13 to +160 °F) |
| Suitable grease consistency | NLGI 2, 3 | IP rating | IP 67 |
| Maximum pressure | 205 bar (2 970 psi) | Lubrication tubes | TLMP 1008: 20 m (65 ft), 6 x 1,5 mm, Nylon TLMP 1018: 50 m (164 ft), 6 x 1,5 mm, Nylon |
| Maximum distance length to lubrication point | 5 m (16 ft) | Weight | Approx. 6 kg (13 lb) |
| Dispense rate | 0,1 - 40 cm³/day (0.003 -1.35 US fl.oz/day) per outlet | Ordering details 8 outlets | |
| Output pump element | Approx. 0,2 cm³ (per cycle), approx. 1,7 cm³ (per minute) | TLMP 1008/24DC | 24 V DC (–20/+30%) |
| Reservoir size | 1 litre | TLMP 1008/120V | 120 V AC 60 Hz (±10%) |
| Useable reservoir volume | Approx. 0,5-0,9 litres (17-30 US fl.oz) | TLMP 1008/230V | 230 V AC 50 Hz (±10%) |
| Filling | Via hydraulic lubrication fitting R1/4 | Ordering details 18 outlets | |
| Installation position | Vertical (max deviation ±5°) | TLMP 1018/24DC | 24 V DC (–20/+30%) |
| Power Supply Connector | EN 175301-803 DIN 43650/A | TLMP 1018/120V | 120 V AC 60 Hz (±10%) |
| Alarms | blocked feed lines, empty reservoir internal and external | TLMP 1018/230V | 230 V AC 50 Hz (±10%) |
Accessories
A full range for enhanced versatility of SKF automatic lubricators
Connectors
| LAPA 45 | Angle connection 45° | |||
| LAPA 90 | Angle connection 90° | |||
| LAPE 35 | Extension 35 mm | |||
| LAPE 50 | Extension 50 mm | |||
| LAPF F1/4 | Tube connection female G1/4 | |||
| LAPF M1/8 S | Tube connection male G1/8 for 6 x 4 tube | |||
| LAPF M1/4 S | Tube connection male G1/4 for 6 x 4 tube | |||
| LAPF M1/8 | Tube connection male G1/8 | |||
| LAPF M1/4 | Tube connection male G1/4 | |||
| LAPF M1/4SW | Extra strong tube connection male G1/4 | |||
| LAPF M3/8 | Tube connection male G3/8 | |||
| LAPG 1/4 | Grease nipple G1/4 | |||
| LAPM 2 | Y-connection |
| LAPN 1/8 | Nipple G1/4–G1/8 | |||
| LAPN 1/4 | Nipple G1/4–G1/4 | |||
| LAPN 1/2 | Nipple G1/4–G1/2 | |||
| LAPN 1/4 UNF | Nipple G1/4–1/4 UNF | |||
| LAPN 3/8 | Nipple G1/4–G3/8 | |||
| LAPN 6 | Nipple G1/4 – M6 | |||
| LAPN 8 | Nipple G1/4 – M8 | |||
| LAPN 8x1 | Nipple G1/4–M8 x 1 | |||
| LAPN 10 | Nipple G1/4–M10 | |||
| LAPN 10x1 | Nipple G1/4–M10 x 1 | |||
| LAPN 12 | Nipple G1/4 – M12 | |||
| LAPN 12x1.5 | Nipple G1/4–M12 x 1,5 |
[Legend: SKF LAGD Series, SKF TLSD Series, SKF TLMR Series]
Non return valves (for oil applications)
| LAPV 1/4 | Non-return valve G1/4 | |
| LAPV 1/8 | Non-return valve G1/8 |
Brushes (for oil applications)
| LAPB 3x4E1 | Brush 30 x 40 mm | |
| LAPB 3x7E1 | Brush 30 x 60 mm | |
| LAPB 3x10E1 | Brush 30 x 100 mm | |
| LAPB 5-16E1 | Elevator brush, 5–16 mm gap | |
| LAPB 5-16/2K | Elevator kit for 5, 9 or 16 mm rail |
Mounting and protecting devices and extras
| LAPC 13 | Bracket | |
| LAPC 50 | Clamp | |
| LAPC 63 | Clamp | |
| LAPP 4 | Protection base | |
| LAPP 6 | Protection cap | |
| LAPT 1000 | Flexible tube, 1 000 mm long, 8 x 6 mm | |
| LAPT 5000 | Flexible tube, 5 000 mm long, 8 x 6 mm | |
| LAPT 1000S | Flexible tube, 1 000 mm long, 6 x 4 mm | |
| LAPT 5000S | Flexible tube, 5 000 mm long, 6 x 4 mm | |
| LAPT 1000SW | Extra strong flexible tube, 1 000 mm long, 8 x 6 mm | |
| LAPT 5000SW | Extra strong flexible tube, 5 000 mm long, 8 x 6 mm | |
| TLMR 201-1 | Cable plug M12x1 for TLMR 201, type M12-A | |
| TLSD 1-BATC | Lithium battery pack for TLSD 125/250 |
Quick tool for relubrication calculation
SKF DialSet
SKF DialSet has been designed to help you to set up your SKF automatic lubricators. After selecting the criteria and grease appropriate for your application, the program provides you with the correct settings for your SKF automatic lubricators. It also provides a quick and simple tool for relubrication intervals and quantity calculations.
- Allows quick calculation of the relubrication intervals based on the operating conditions of your application
- Calculations are based on SKF lubrication theories
- Calculated lubrication intervals depend on the properties of the selected grease, thereby minimising the risk of under- or overlubrication and optimising grease consumption
- Calculations take into account SKF automatic lubrication systems, grease dispense rates, thus facilitating the selection of the correct lubricator setting
- Recommended grease quantity depends on the grease replenishment position; side or W33 for optimum grease consumption
- Includes a complete list of the SKF SYSTEM 24 accessories
The program is accessible free-of-charge on dialset.skf.com
[Image Description: SKF DialSet relubrication calculation software interface shown on a laptop, tablet, and smartphone. A QR code is also visible.]
Visit skf.com | skf.com/lubrication | skf.com/mapro
SKF and SYSTEM 24 are registered trademarks of the SKF Group. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. App Store is a service mark of Apple Inc. registered in the US and other countries. Android and Google Play are trademarks of Google Inc.
SKF Group 2024. The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.
PUB MP/P8 17099/8 EN February 2024. Certain image(s) used under license from Shutterstock.com.
