Philips Dynalite PAXBPA AntumbraButton User Interface Installation Instructions
Installation Instructions
Important Safety Information: Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
French: Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux.
German: Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren.
Spanish: Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras.
Italian: I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici.
Dutch: De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften.
Japanese: 装置を取り付ける際は、資格のある電気技師に依頼し、国および地域の電気および建設に関するすべての法令に従ってください。
Chinese: 根据国家/地区及当地的电气与建筑规范和法规,该设备必须由有资质的电工进行安装。
Arabic: يجب تركيب الأجهزة من قبل فني كهربائي مؤهل وفقا لكافة قوانين ولوائح التركيب الكهربائي المحلي والوطني.
Mounting and Wiring Diagram
[Diagram showing wall box preparation with dimensions: minimum 300mm (11.81 in) clearance]
[Diagram showing mounting plate and button assembly]
[Diagram showing the PAXBPA unit and its dimensions: 116 mm (4.56 in) height, 84 mm (3.30 in) width]
[Diagram showing the back of the unit with connection terminals and dimensions: 75 mm (2.95 in) width, 36 mm (1.41 in) depth]
[Diagram illustrating wiring connections for power, data (RS-485 DyNet), and ground. Shows wire gauge compatibility: 0.3-2.5mm² (22-12 AWG) and torque setting: 0.4 Nm (3.5 Lb-in)]
[Diagram showing the unit being mounted into the wall box with screws]
[Diagram illustrating the connection of RS-485 DyNet cables to the unit]
[Diagram showing multiple PAXBPA units installed together]
Electrical Specifications and Compliance
Power Requirements: SELV/Class 2 (UL)
Voltage/Current: 12 V, 20 mA; 24 V, 35 mA
Maximum Current: ≤ 2 A
Torque Setting: 1.0 Nm (8.8 Lb-in) for mounting screws
IEC Overvoltage Category: III
Operating Temperature: -5° C (23° F) to 50° C (122° F)
Operating Humidity: ≤ 90%
IEC Pollution Degree: II
FCC Compliance Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications not approved by the manufacturer of this device could void the user's authority to operate this device.
This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B).
Installation of a home and building automation and control system shall comply with HD 60364-4-41. The temperature limits and current-carrying capacities for the communication wires specified in HD 384.5.523 shall not be exceeded.
Do not connect inputs to mains.
Disconnect power before connecting or separating modules.
General Information
© 2021 Signify Holding. All rights reserved. Specifications are subject to change without notice.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.
For more information, visit: www.lighting.philips.com/dynalite
