Tala The Muse User Guide

Introduction

This guide provides essential information for the setup, operation, and care of your Tala The Muse portable lamp.

Preparation

Please read these instructions thoroughly before installation and keep them for future reference. Improper assembly can undermine the safety and longevity of the product.

Important Information & Warnings

Important Notes

• All packaging must be removed and the bulb carefully screwed in before turning the product on.
• The product is designed to work exclusively with the Tala 12V LED bulb provided. Using alternative bulbs may result in ineffective operation. For replacements, visit the Tala website or contact customer service.
• Avoid operating the product in temperatures above 35°C, as this can reduce lumen output and bulb lifespan.
• To reduce the risk of scratches or marking, ensure the bulb is fully housed within the glass case, except when changing the bulb.

Warnings

• The Muse is not suitable for recessed or enclosed fixtures or environments and should be displayed as instructed.
• Do not leave the product under direct sunlight while switched on.
• Ensure all fixings are tightly sealed to prevent internal components and surfaces from being exposed to water.

Product Details

SKUs

• SKU - FB-MUSE-PBL-PG-01
• SKU - FB-MUSE-PBL-PR-01
• SKU - FB-MUSE-PBL-CW-01
• SKU - FB-MUSE-PBL-HB-01
• SKU - MUSE-PBL-SB-01

Specifications

The Muse Lamp:

• Dimensions: Ø12.5 x 33.8cm / Ø5 x 13.3in
• IP Rating: IP44 (Suitable for Wet locations)
• Power Input: 5V/2A USB Type-C
• Wireless Charging: 5W
• Battery: Li-ion 13.2Ah 3.7V 48.8Wh
• Maximum Ambient Temperature: 35°C
• Compatibility: Use only with Tala The Muse 12V bulbs.

Included Bulb:

• Voltage: 12V
• Wattage: 6W
• Lumen Output: 400lm
• Base Type: E27
• Equivalent Wattage: 35W replacement
• Current: 0.5A
• Color Rendering Index (CRI): 97
• R9 Value: 95
• Color Temperature: 2000-2800K
• Dimensions: Ø6 x 11cm
• Flicker Rate: <1%

Certifications & Ratings:

• FCC Compliant (Class B digital device)
• ETL Listed
• CE Marked
• UKCA Marked
• IP44

Provided Components

The following items are included with your Tala The Muse:

• A: x1 The Muse luminaire
• B: x1 The Muse LED bulb in box
• C: x1 Flat-head screwdriver
• D: x1 USB Type-C Charging cable

Lamp Components

The Muse lamp consists of the following parts:

1. Handle
2. Lid
3. 12V LED bulb
4. Lampholder coil
5. Dimmer dial
6. Base
7. Battery charge level button
8. USB Type-C power input
9. Battery charge level Indicator lights

Initial Setup

1. Step 1: Remove Handle

   Release the two screws (marked 1a) on the lid using the provided flat-head screwdriver (B) and carefully remove the handle (1).

2. Step 2: Access Lamp Interior

   Lift off the lid (2) and carefully remove all packing material from inside the lamp, including the bulb box.

3. Step 3: Install Bulb

   Remove the bulb from its box and carefully screw it into the lampholder coil by turning the bulb clockwise. Ensure the bulb is aligned properly and do not overtighten. The glass enclosure can be removed after initial installation for easier access to the bulb and lampholder coil.

4. Step 4: Secure Bulb Contact

   Ensure the bulb is screwed in fully and that contact is made between the base of the bulb and the housing, without overtightening. Both the bulb and housing are safe to touch.

   Important Note on Tightening: Over-tightening or under-tightening the bulb can cause misalignment. If this occurs, make small adjustments until the bulb is straight and just touching the contact point.

5. Step 5: Reassemble Lid and Handle

   Return the lid and handle to their original positions and tighten the screws to secure the handle in place.

6. Step 6: Power On and Adjust Brightness

   To turn on the lamp, rotate the dimmer dial on the front of the lamp clockwise until the bulb lights up. Adjust the dimmer for your desired light output: dial up for a cooler white light, and dial down for a warmer, ambient colour temperature.

Charging The Muse

Option 1: Wired Charging

Insert the provided USB Type-C charging cable into the input port located at the back of the luminaire base and plug it into a USB Type-A adapter. For optimal charging, use the supplied 0.5m charging cable and a 2-Amp USB Type-A adapter.

Option 2: Wireless Charging

Place the assembled product flat on a compatible wireless charging pad. Ensure it is positioned in the centre of the pad for effective charging.

Charging Indicators: When charging correctly, the battery charge level indicator lights (8) will start blinking. Total charging time is approximately 8 hours when wired or 10 hours when wireless.

Battery Level Indicator

To check the current battery level:

• Press the button on the back of the lamp to display the battery level indicators on the front of the lamp.
• Press the button twice to turn the indicator lights off.

Indicator States:

• Blinking: Less than 10% Battery remaining ? (blinking)
• Solid: 25% Battery remaining ? (solid)
• Two lights illuminated: 50% Battery remaining ??
• Three lights illuminated: 75% Battery remaining ???
• Four lights illuminated: More than 75% Battery remaining ????

Tips to Prolong Battery Life

The Muse uses a Lithium-ion battery pack rated for 1000 full charge/discharge cycles. After this period, the battery capacity may begin to noticeably degrade.

• Once fully charged, please remove the lamp from the charger.
• Avoid allowing the battery to reach 0%. Recharge when the low-battery indicator begins to blink.
• When the lamp is not in use, store it with a battery charge between 25-50% (indicated by 1-2 lights).
• During charging, ensure The Muse is uncovered to prevent over-heating.
• Depending on the charger's power output, the lamp may not always reach 100% charge if the bulb is illuminated at the same time.

Care and Cleaning

We recommend cleaning the lamp with a soft, dry cloth. If necessary, further cleaning can be achieved with warm, soapy water. Do not use abrasive materials, alcohol, or other solvents, as these can damage the product's finish.

Extended use in wet or humid locations can cause condensation to form inside the glass tube. To address this, please follow the 'Initial Set-Up' steps to open the lid and allow condensation to evaporate. To prevent condensation, it is recommended that the lamp is not exposed to wet weather for prolonged periods, such as being left outdoors overnight.

Warranty and After-Care

This product comes with a two-year warranty. If you encounter a functional defect with the product during this period, please contact our customer service team at customerservice@tala.co.uk.

Compliance, Recycling, and Community

WEEE Symbol

The symbol ? indicates that electrical and electronic equipment (WEEE) should not be mixed with general household waste. For recovery and recycling, please take this product to a designated collection point where it will be accepted free of charge. Many retailers offer this service in-store. Disposing of this product correctly helps save valuable resources and prevents potential negative effects on human health and the environment.

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician for help. Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Join the Community

Connect with Tala:

• Instagram: @tala
• Facebook: talaHQ
• Pinterest: TalaLED
• Tag your photos: lighttoliveby

Contact Information

• Tala Energy Ltd
  25B Vyner Street, London, UK, E2 9DG
  hello@tala.co.uk
• Tala Europe B.V
  Bertus Aafjeshove 40, Nieuwegein 3437JN, Netherlands
• Tala North America, Inc.
  2 Research Place, Suite 300, Rockville, MD 20850, USA