Product Overview
The ArcSource Outdoor 4 MC is a Cree MC-E RGBW multichip based high-powered multicolored LED fixture. The unit is suitable for large-scale applications as well as individual illuminating needs.
1. Attention
Consider the respective national norms during installation.
- Do not install the unit near naked flames.
- Avoid using the unit in locations subject to possible impacts.
- Do not attempt to dismantle or modify the unit.
- Do not install the module in a badly ventilated location.
Avoid looking directly into the LED light beam at close range!
Immunity of the equipment is designed for electromagnetic environments E1, E2, E3 according to the standard EN55103-2 ed.2 Electromagnetic compatibility. This is a product family standard for audio, video, audiovisual, and entertainment lighting control apparatus for professional use. Part 2: Immunity.
The installation company should check levels of possible interferences above the tested levels E1, E2, E3 given by this standard (e.g., transmitters in the surrounding area) before installing the equipment.
Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia equipment – Emission Requirements according to class B.
2. Installation
The ArcSource Outdoor 4 MC can be arranged in any position or orientation. Three holes of diameter 4.3mm in the ArcSource Outdoor's base serve for mounting on a non-flammable surface. The light head can be adjusted against the base in a range of 120°.
CAUTION! Avoid looking directly into the LED light beam at close range!
CE: The ArcSource Outdoor units should be connected to the ArcPower drivers stated in technical specifications. Refer to their user manuals for full details of mains power requirements and DMX operation.
The maximum possible number of LED modules connected to one LED output of the ArcPower driver is mentioned in the table below:
| Max. number of connected modules | ArcPower drivers |
|---|---|
| 12 | ArcPower Rack Mount, DRS, ArcPower 48 Outdoor, ArcPower 192 Outdoor |
| 6 | ArcPower 24 outdoor |
Use a cable splitter if more than one LED module needs to be connected to one LED output of the ArcPower driver. The connection cable between the ArcPower and the splitter is a standard RJ45 patch cable category 5 wired 1:1.
US: The ArcSource Outdoor unit must be connected to a power source of type LVLE according to the specifications stated in the chapter "Technical specifications".
The enclosed adapter stand (with M5x45 screw) allows placing the light head to a higher position.
Diagram Description: A diagram shows the ArcSource Outdoor 4 MC fixture with an adapter stand attached, illustrating how it elevates the unit. The diagram includes a plus symbol (+) and an adapter component.
3. Connection
ArcSource Outdoor 4 MC
Diagram Description: A diagram shows the rear view of the ArcSource Outdoor 4 MC fixture with a Chogori connector. A table lists the pin functions (1-8) and corresponding wire colors (Red-, White+, White-, Blue-, Blue+, Green-, Green+, Red+).
Adapter cable Chogori -Chogori (not a standard part of delivery)
Diagram Description: A diagram shows an adapter cable with Chogori connectors on both ends. The left end is a female Chogori connector (08BFFA-SL8001) and the right end is a male Chogori connector (08BMMA-SL8001). Tables for both connectors list pin functions (1-8) and corresponding wire colors (e.g., Red -, Grey; White +, Pink). The diagram shows rear views of both connectors.
Adapter cable Chogori -RJ45, for indoor use only (not a standard part of delivery)
Diagram Description: A diagram shows an adapter cable with a female Chogori connector (08BFFA-SL8001) on the left and an RJ45 connector on the right. Tables for both connectors list pin functions (1-8) and corresponding wire colors (e.g., Chogori: Red -, Blue/white; RJ45: Red +, Orange/white). The diagram shows rear views of both connectors. An arrow indicates connection to an ArcPower unit.
Connection to the ArcPower driver
Diagram Description: A diagram illustrates the connection between the ArcSource Outdoor 4 MC fixture and an ArcPower driver using a cable. Labels indicate "CE: ArcPower driver" and "US: Power source LVLE".
4. Technical Specifications
| LED Device: | Cree MC-E multichip |
| Available beam angles: | 7°, 13°, 20°, 30°, 40°, 60°, 90°, 7° x 30°, 30° x 7°, 7° x 60°, 60° x 7°, 35° x 70°, 70° x 35°, 10° x 90°, 90° x 10° |
| Colour variants: | RGBW, RGBA, WW |
| Max. Current per Colour: | 700 mA |
| Max. Power Consumption: | 10 W @ 700 mA (6 W @ 350 mA) |
| Recommended Power Supplies (CE): | ArcPower Rack Unit, ArcPower 24 Outdoor, ArcPower 48 Outdoor, ArcPower 192 Outdoor, DRS |
| Recommended Power Supplies (US): | Power source LVLE type only |
| Projected Lumen Maintenance: | L90B10 >90,000 hrs, Ta = 25°C / 77°F |
| Cooling System: | convection |
| Operating Ambient Temperature: | -20 °C / +45 °C (-4 °F / +113 °F) |
| Operating Temperature: | +75 °C @ Ambient +45 °C (+167 °F @ Ambient +113 °F) |
| Housing: | aluminium |
| Weight: | 0.43 kg / 0.95 lbs |
| Mounting: | via 3 holes in the base |
| Connection: | Cable LiYY 8xAWG22 UL Style 2517/CSA O.D. 6.70mm, length=50 cm; Chogori CGRBDU-08BMMA-SL8001 (connector, male) |
| Protection factor (CE): | IP 67 |
| Protection factor (US): | Suitable for wet locations |
5. Accessories
- 1x Connector Chogori CGRBDU-08BFFA-SL8001 (female), IP=67
- 1x Adapter stand (Part Number 19730251)
- 1x Screw M5x45
- 1x Allen key 4
- 1x Splitter (Part Number 13050690)
6. Optional Accessories
- Adapter cable CGRBDU-08BFFA/ CGRBDU-08BMMA, Length 3m (Part Number 13051960), IP=67
- Adapter cable CGRBDU-08BFFA/RJ45, Length 0.25m (Part Number 13051966), for indoor use only
- T-connector Chogori 8-pin (Part Number 13051938), IP=67
- Land spike 1 ASO 4 MC 100mm (Part Number 10980178)
- Land spike 2 ASO 4 MC 100mm (Part Number 10980179)
- Land spike 1 ASO 4 MC 500mm (Part Number 10980180)
- Land spike 2 ASO 4 MC 500mm (Part Number 10980181)
- Land spike 3 ASO 4 MC 500mm (Part Number 10980183)
- Top hat ArcSource Outdoor 4 MC (Part Number 10980273)
- Half top hat ArcSource Outdoor 4 MC (Part Number 10980253)
7. Dimensions (mm)
Diagram Description: A series of diagrams illustrate the dimensions of the ArcSource Outdoor 4 MC fixture.
Main Fixture Dimensions:
Diagram Description: Two side views of the fixture are shown. The left view shows a height of 145mm, with the base at 73mm and the top at 64mm from the base. The total width is 90mm. The right view shows a slightly different configuration with a height of 115mm and base at 42mm. Both views show a base diameter of Ø 62mm and a rear connector.
Top View and Adjustment Range:
Diagram Description: A top view of the fixture's base shows a diameter of Ø 62mm. An arc indicates a 120° adjustment range for the light head. Another dimension shows Ø 44mm. A hole diameter of Ø 4.3mm is also indicated.
Fixture with Half Top Hat:
Diagram Description: Front and side views of the fixture equipped with a half top hat. The side view shows a width of 72mm and a height of 70mm from the mounting point. The front view shows a width of 41mm and the Anolis logo.
Fixture with Top Hat:
Diagram Description: Front and side views of the fixture equipped with a full top hat. The side view shows a width of 72mm and a height of 70mm from the mounting point. The front view shows a width of 41mm and the Anolis logo.
8. Installing the ArcSource Outdoor 4 MC onto a land spike
Diagram Description: A series of diagrams illustrate the assembly of the ArcSource Outdoor 4 MC onto various land spike configurations. Each diagram shows numbered parts corresponding to the installation steps.
Land spike 1 ASO 4 MC 100mm / Land spike 2 ASO 4 MC 100mm
- Hammer the sharp part (1) of the land spike into the ground (hammer the center of the sharp part, not the edge).
- Screw the threaded bar (2) into the sharp part (1) and secure it with the socket head M5x5 (3).
- Put the cover (4) on the threaded bar (2).
- Put the pipe 36.5mm (5) on the threaded bar (2).
- Put the cable holder (6) on the threaded bar (2).
- For Land spike 1 ASO 4 MC 100mm only: Screw the nut (7) on the threaded bar (2).
- For Land spike 1 ASO 4 MC 100mm only: Screw the ArcSource Outdoor 4 MC onto the nut (7) using the socket head M5x14 screws.
- For Land spike 1 ASO 4 MC 100mm only: Pass the cable through the cable holder (6).
- For Land spike 2 ASO 4 MC 100mm only: Put the pipe 42mm (6) on the threaded bar (2).
- For Land spike 2 ASO 4 MC 100mm only: Put the ArcSources holder (8) on the threaded bar (2).
- For Land spike 2 ASO 4 MC 100mm only: Screw the nut (9) on the threaded bar (2).
- For Land spike 2 ASO 4 MC 100mm only: Screw both ArcSource Outdoor 4 MC units onto the ArcSources holder (8) using the socket head M5x14 screws.
- For Land spike 2 ASO 4 MC 100mm only: Pass the cable through the cable holder (6).
Land spike 1 ASO 4 MC 500mm / Land spike 2 ASO 4 MC 500mm
- Hammer the sharp part (1) of the land spike into the ground (hammer the center of the sharp part, not the edge).
- Screw the threaded bar (2) into the sharp part (1) and secure it with the socket head M5x5 (3).
- Put the cover (4) on the threaded bar (2).
- Put the pipe 36.5mm (5) on the threaded bar (2).
- Put the cable holder (6) on the threaded bar (2).
- Put the pipe 198mm (7) on the threaded bar (2).
- Put the cable holder (6) on the threaded bar (2).
- Put the pipe 198mm (7) on the threaded bar (2).
- For Land spike 1 ASO 4 MC 500mm only: Put the cable holder (6) on the threaded bar (2).
- For Land spike 1 ASO 4 MC 500mm only: Screw the nut (8) on the threaded bar (2).
- For Land spike 1 ASO 4 MC 500mm only: Screw the ArcSource Outdoor 4 MC onto the nut (8) using the socket head M5x14 screws.
- For Land spike 1 ASO 4 MC 500mm only: Pass the cable through the cable holders (6).
- For Land spike 2 ASO 4 MC 500mm only: Put the ArcSources holder (8) on the threaded bar (2).
- For Land spike 2 ASO 4 MC 500mm only: Screw the nut (9) on the threaded bar (2).
- For Land spike 2 ASO 4 MC 500mm only: Screw both ArcSource Outdoor 4 MC units onto the ArcSources holder (8) using the socket head M5x14 screws.
- For Land spike 2 ASO 4 MC 500mm only: Pass the cable through the cable holders (6).
9. Installing the top hat (half top hat)
Diagram Description: Diagrams show the process of attaching a top hat or half top hat to the ArcSource Outdoor 4 MC fixture. Numbered parts are indicated.
- Unscrew the Allen head screw (1) from the ArcSource Outdoor 4 MC housing.
- Insert the distance part (4) into the housing of the ArcSource Outdoor 4 MC and place the top hat (5) or half top hat (5) on the housing (6).
- Screw the Allen head screw (1) back to the housing with a spring washer (2) and flat washer (3). The small hook (7), which secures the top hat (or half top hat) to the housing, must be placed between the distance part (4) and the flat washer (3). Check that the Allen head screw is fully tightened.
Diagram Description: Two illustrations show the attachment of a top hat and a half top hat. The first shows the fixture with components labeled 1, 2, 3, 4, and 6, with a top hat labeled 5 being attached. The second shows a similar setup for a half top hat. A hook (7) is also depicted.
