ScanGrip MULTIMATCH R

Product Overview

The ScanGrip MULTIMATCH R is a versatile work light designed for various professional and personal applications. It features adjustable brightness and color temperature (CCT), a CCT SCAN mode for continuous color temperature adjustment, and a built-in power bank with a USB outlet for charging mobile devices.

Key Features:

• Ultra high CRI+ COB LED
• Adjustable brightness: 1200 lm (100%), 900 lm (75%), 600 lm (50%), 300 lm (25%), 120 lm (10%)
• Adjustable CCT: 2500K - 6500K
• CCT SCAN mode for continuous color temperature adjustment
• CRI 96+
• Built-in power bank with USB outlet (5V, 1A, 5400mAh)
• Battery life: 3.5h (at 100% brightness), 10h (at 50% brightness)
• Operating temperature: -10°C to +40°C
• Impact resistance: IK07
• Water and dust protection: IP67
• Dimensions: 155x165x64mm
• Weight: 820g
• Includes charger (100-240V AC, 50-60Hz input; 5V DC, 2A output)

Visual Description of Product:

The ScanGrip MULTIMATCH R is a rectangular work light with a dark grey housing. The front features a large, circular COB LED panel surrounded by a red ring. Below the LED panel are four control buttons labeled A, B, C, and D. The light has an adjustable stand for positioning. On the back, there is a built-in power bank with a USB outlet for charging external devices. The product comes with a power adapter and USB cable.

Operation

Powering On/Off: Press button A.

Brightness and CCT Control:

• Press and hold button A to switch between brightness control and CCT Kelvin manual adjustment.
• Press button B to increase brightness/CCT Kelvin.
• Press button C to decrease brightness/CCT Kelvin.

CCT SCAN Mode:

• Press button D to activate CCT SCAN mode.
• Once activated, press the CCT SCAN button to select the desired CCT SCAN value. The color temperature will continuously increase from 2500K to 6500K and back in a loop.
• Press button D to pause CCT SCAN mode.
• Press and hold button D at any time to exit CCT SCAN mode.

Charging and Battery

• Use a USB charger rated for 5V, 2A.
• Always replace the battery with a new one of the same type and grade.
• Do not leave the battery flat; it may become over-discharged and unusable.
• The luminaire is only suitable for direct mounting on non-combustible surfaces.
• Charging should be done indoors only.

Powerbank Functionality

The built-in power bank provides a USB outlet for charging mobile devices. It has an output of 5V, 1A and a capacity of 5400mAh.

Safety Warnings

• Always respect applicable legislation for working with electrical equipment to reduce the risk of accidents.
• Avoid looking directly into the beam of light, as this can cause dazzling.
• Do not use the lamp near an open flame.
• The light source of this luminaire is not replaceable; when it reaches the end of its life, the entire luminaire must be replaced.
• Opening the lamp is not advisable, as it may compromise its water-tightness.
• Fire Hazard: Maintain a minimum distance of 0.1m from lighted objects.
• Dispose of electrical products responsibly at recycling facilities.
• Remove the battery before disposing of the device.
• Disconnect the device from the mains before removing the battery.
• Dispose of the battery safely.

Manufacturer's Warranty (Australia and New Zealand)

This ScanGrip product is guaranteed for two (2) years from the date of purchase. The guarantee is void if the product is misused, tampered with, or accidentally damaged. In case of a defect, ScanGrip will repair or replace the product or its defective parts, or offer partial compensation. This guarantee is in addition to other consumer rights and remedies available under Australian or New Zealand Consumer Law.

For warranty claims, return the product to the original place of purchase with your receipt, or visit www.scangrip.com to fill out a claim form.